01432 610152 Get a quote Call 01432 610152

Lead on slate

Lead details on a slate roof: soakers, valleys and abutments

On a slate roof the lead keeps weather out at every wall, chimney and valley. This guide covers soakers, valley gutters and abutment flashings, and the lead code each takes.

Horizon Roofing Hereford 9 min read

Slate sheds water by overlap: each course lies over the head of the one below. Across an open slope that is all a roof needs. Trouble starts where the slope stops, at a chimney stack, the flank of a neighbouring house, a dormer cheek or the fold between two roofs. Slate cannot be wrapped round a corner or tucked into a wall, so the junction is handed to a softer metal. On slate that metal has long been lead.

This guide follows three lead details: soakers, valley gutters and abutment flashings. For each it says what the detail is, where it hides, which sheet thickness suits it, how it fails and what mending it takes. A last section covers cost, and the approval questions that arise in England and in Wales once lead work becomes part of a re-slate.

It sits under our slate roofing page, and the metal itself has a section of its own at lead roofing.

Where slate stops and lead starts

Think of the roof as two systems. Across the open slope the slates do the work by overlap, one course shading the next. At the edges a second system takes over, and it has to cope with three kinds of meeting: slate against masonry, slate against slate at an angle, and slate against a stack that stands up through the slope.

Lead is chosen because it can be beaten flat against stone, folded over an edge and then left alone. Its weakness is thermal movement. Sheet lead swells in the sun and contracts in frost, and a piece that cannot slide a little will eventually split along its fold. Good leadwork is therefore laid in modest lengths with room to move, and its fixings are few and placed on purpose.

The three lead details on a slate roof
DetailWhere it sitsIts job
SoakerUnder the slates, beside a wallSends water back out over the slates
Abutment flashingStepped into the wall aboveCovers the top edge of the soaker
Valley gutterBetween two slopesDrains both slopes to the eaves

Each detail is checked from two sides. From the loft, a stain on a timber shows which wall or valley is leaking. From the roof, the lead itself can be seen, handled and photographed. Slate roofs can have one junction in poor order and the rest sound, so the survey notes them one at a time and does not give the whole roof a single verdict.

Soakers: the lead you cannot see

A soaker is a plain piece of lead sheet bent into an L. One leg lies flat on the batten under a slate. The other leg stands against the wall or chimney. There is a soaker for every course, cut to the size of the slate it serves, so each one is hidden by the slate above it.

Nothing of this shows from the ground. Rain that gets past the wall flashing runs down the standing leg, drops onto the slate below and carries on down the slope. If a soaker is missing, split or too short, the rain has nowhere to go but behind the slates. A slate roof can look perfect from the garden while a wall inside is slowly soaking.

Royston Lead's brochure lists Code 3 as "Recommended for lead soakers only", and Code 4 as suitable for soakers as well. The only way to see which was fitted is to lift the slates beside the wall, which is also the only way to replace one. When the slates are up, we check:

  • that every course has a soaker, with none missing where an old repair was made
  • that each soaker is whole, with no split along its fold
  • that the standing leg is tall enough to sit behind the flashing above
  • whether mastic or bitumen has been smeared on in place of new lead
  • that the slates are numbered and sound enough to go back

Our guide to lead soakers under tiles and slates covers the fitting in more detail.

Valley gutters between two slopes

A valley gutter is the one place on a slate roof that is drained by metal and not by the slates. The lead lies on boards in the fold between two slopes. The slates on each side are cut to a straight line along it, leaving a channel of bare lead that carries the water down to the gutter at the eaves. Royston Lead lists Codes 4, 5, 6, 7 and 8 for this use, so the choice runs from lighter sheet to the heaviest and follows the roof the valley has to drain.

Everything that falls on both slopes lands in the same channel. A small fault therefore does more harm than it would on an open slope, and a split can soak a broad patch of ceiling whose stain sits well away from it. Cut slates beside the lead matter as much as the lead: if they are chipped or short, water is thrown across the channel and under the opposite edge.

On a valley we look for:

  • splits or hairline cracks along the fold of the lead
  • sheet that has slumped down the boards, leaving the top edge bare
  • edge slates that are cracked, short or cut unevenly
  • moss, slate grit and leaves packed into the channel
  • mastic or bitumen smeared over earlier repairs

Our guide to lead valley gutters follows the build-up layer by layer, and the one on why a lead valley leaks works through the faults.

Abutments, chimneys and stepped flashings

Where a slate roof runs up to a wall, that wall may be a neighbour's gable, the flank of an extension or the side of a chimney stack. The soakers stand against it. Above them sits the stepped flashing, lead cut in stair-steps that follow the brick or stone courses, pushed into a groove cut along the mortar joint and pointed over. The soaker takes the water off the slates. The flashing covers the soaker's top edge, so water cannot run behind it.

A chimney adds one more piece. A back gutter is a small gutter of lead set behind the stack, so that water is led round it and cannot bank up against the brickwork. Where the stack is stone and its joints have worn back, they need repointing before new lead can be tucked in, so we look at the masonry before the lead is ordered.

At the front of a chimney the flashing changes shape. There it is an apron, a sheet that lies over the slates below the stack and is lapped onto them, while on each side the stepped lead climbs the slope with the courses. Renewing a stepped flashing follows a set order:

  1. The slates beside the wall are lifted and numbered.
  2. The soakers are checked, and any split or missing one is replaced.
  3. The old flashing is cut out and the joint is raked clear.
  4. The new lead is tucked in, pointed and dressed down.
  5. The slates go back in their numbered order.

See also step, apron and cover flashings and the back gutter behind a chimney.

Reading the lead code

Sheet lead is sold by code, and the code is a thickness. Royston Lead's cast-lead brochure gives each code a colour and a list of jobs. Its use letters run from soakers to dormers, and the table below spells them out.

Lead codes from Royston Lead's brochure
CodeThicknessColourListed uses
31.32 mmGreenSoakers only
41.80 mmBlueSoakers, flashings, valleys, dormers
52.24 mmRedFlashings, valleys, box gutters, dormers
62.65 mmBlackFlashings, valleys, box gutters, dormers

The pattern is simple. A soaker is small and sits under a slate, so it takes the thinnest sheet on the list. A valley gathers two slopes and takes the thicker codes, and a flashing that must be dressed into stone sits in between. Codes 7 and 8 are listed for valleys, box gutters and dormers. Lead is outside the flat-roof standard BS 6229:2025, which covers membranes, so lead on a slate roof is judged by its code and its laying and not by that standard, and a flat-roof fall figure does not apply to a pitched valley.

On lifespan, MyJobQuote's lead page makes a hedged claim: correctly installed flashing "can last for over 80 years". It is a statement about flashing, and it says nothing about the slates around it. Slates and lead age at their own rates, so a sound flashing can outlive the slates beside it, and the other way round. Neither figure is a promise, and the survey judges the lead in front of us.

Repair, price and approval in England and Wales

Lead repairs on slate range from one soaker to a whole elevation. Access matters, because a chimney flashing may need a scaffold or a roof ladder set up on the slope, and that is worked out at the survey. Where the slates are sound, only the courses beside the detail are lifted and relaid. Where the edge slates are cracked or nail-sick, the job turns into a partial re-slate, and the photographs of both show which it is.

For a sense of scale, MyJobQuote's 2026 guide gives around £200 for patching a chimney lead flashing and around £570 for replacing it. It puts full leadwork at between £350 and £920, and notes that the total swings mainly with the need for scaffold. These are national figures from a single cost guide, with no link to any one Herefordshire roof. Your own price is a single written total that follows the survey, and the quote states what is and is not included.

Replacing lead is a repair. Re-covering a slope as well brings in an approval question, and the answer depends on which country the property is in:

  • In England, the Planning Portal says no Building Regulations application is normally needed where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" is affected.
  • In Wales, the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval."

Before a larger lead job starts we ask the council's building control team, or a registered building control approver, which answer applies. The full process is in our guide to re-slating a roof.

Lead on slate: your questions

Do new soakers mean the whole slope has to be re-slated?

No. Soakers lie under the slates along the wall or chimney, so only the courses beside the detail are lifted, numbered and relaid. If those slates are cracked or nail-sick, you are shown the evidence and why they should go. Sound slates are put back where they came from.

How do I tell soaker trouble from a slipped slate?

Damp that sits beside a wall, chimney or party wall points to the soakers and flashing. A slipped slate can be anywhere on the slope, sometimes with an open gap visible from the garden. Photographs from the loft and the roof settle which it is before any work is agreed.

Who decides whether lead work needs approval where I live?

Building control at your council, or a registered building control approver. A repair is one question, and re-covering a large part of the slope is another. The test differs between England and Wales, so we ask building control before any larger job begins, and say which answer we were given.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing