01432 610152 Get a quote Call 01432 610152

Roofers in Coalway

Tile, stack and eaves repairs in Coalway, with re-roofs when a repair would not hold.

Coalway is 24.3 road miles south of central Hereford; we start at the ridge, photograph the faults and write one total price.

Get a free quoteCall 01432 610152

Coalway roofs: tiles, stacks and eaves

  • Older cottages with weathered clay tile roofs and brick chimneys behind a flint wall
    Slipped or cracked tilesLoose tiles let rain reach the battens, and a stain inside can follow.
  • Slate roofs and chimney stacks along a red brick Victorian terrace
    Stacks that carry the weatherEvery face of a stack is exposed, so pointing, flaunching and lead wear together.
  • Newer homes with grey concrete tile roofs along a curving estate road
    Eaves, soffits and guttersFascia, soffit and gutter sit together, so a fault in one affects the others.

Coalway at a glance

Coalway on a street map, with a dashed circle around the town and the nearest towns we cover. Tiles © Esri; map data © Esri, HERE, Garmin, OpenStreetMap contributors.

Tile, stack and eaves, in survey order

What we look at on a Coalway roof, from the slope to the eaves

Three stops make up a Coalway survey: the slope, where tiles slip and battens tire, next the chimney stack with its lead flashings, and finally the eaves, where roof, wall and the nearby conservation areas come into the picture.

A drawn cut-away section through a Herefordshire border house: the front of the main roof is cut open to show the rafters, underlay, battens and slates, beside a black-and-white timber-framed gable. Numbered, from the ridge down: 1 Tiled slope; 2 Stack; 3 Eaves line.

Fig. 1 A Coalway roof in section: slope, stack and eaves, marked 1 to 3.

Callout 1 of 3

Slipped tiles, tired battens and the underlay beneath

The slope is the biggest part of any roof and the part you can see best from the road, so small faults show up here first. A tile slips when the nail or peg holding it gives up, or when the batten under it has gone soft. Finding out which takes two views: one from outside, running an eye along the courses for gaps and dropped lines, and one from the loft with a torch, hunting for daylight, damp patches and darkened timber on the underside of the covering.

Battens are the slim timbers the tiles hang from, and the underlay is the sheet laid over the rafters beneath them. If the underlay has split, a perfectly good covering can still let moisture through. Where only a handful of tiles have moved, we lift the course, check the battens, fix new ones where they are needed and lay the tiles back, with matching replacements for any that have cracked. New tiles beside weathered ones look odd from the road, so we try for a close match in colour and texture before anything is ordered.

A whole-slope re-cover is a different job. The old tiles come off and are sorted, so that sound ones can go back; the battens and underlay are renewed; and the rafters are examined while they are bare, because that is the one moment when every timber can be seen. Only then does the new covering go on, course by course from the eaves up.

Knowing when to stop repairing is part of the job. Marley says roof tiles "are expected to last for around 60 years", while HomeBuilding puts plain concrete tiles at "40-50 years", so for concrete we name both sources and judge your own roof by its condition, not by the calendar. For clay, Marley reports that the BRE determined a minimum life expectancy of 60 years. Pitch matters when a new covering is chosen, too: Marley's product data gives minimum pitches that run from 12.5 degrees for one concrete tile to 40 degrees for the Canterbury, a clay tile, so a covering must suit the slope it goes on.

By the Planning Portal's test for England, a re-cover needs no application as a rule while it touches less than 25 per cent of the building envelope and less than 50 per cent of the roof. Our roof repairs page covers the smaller jobs, and every loose tile we find is photographed from the roof and again from the loft, which lets you see the fault with your own eyes.

A tiled slope, layer by layer

Tiles
Hang from the battens by nails, pegs or clips
Battens
Slim timbers, replaced where they have softened
Underlay
The sheet beneath the battens, checked from the loft
Rafters
The load-bearing timbers, looked at for damp and movement

Seen from the loft, a slipped tile can announce itself with a thin line of daylight.

Fig. 2 The slopes, drawn close

Callout 2 of 3

A Coalway chimney stack, face by face

A stack stands clear of the slope. Rain and wind arrive from all sides, and each face wears a little differently. We study the masonry first: joints that have sunk back from the surface, cracks that run across several courses, units that have started to crumble. Then the top, where the flaunching, a sloped collar of mortar, holds the pots and sends water outward. Nobody sees that from the ground, so we take pictures of all four faces and of the flaunching for the report.

Lead bridges the gap where the stack leaves the roof. Each flashing is a lead strip chased into a mortar joint and laid down over the tiles. Soakers, which are little folded pieces, tuck under each course at the sides. On the high side of each stack there is also a lead tray called the back gutter. Royston Lead's table lists Codes 4, 5 and 6 for flashings and describes Code 3 as "Recommended for lead soakers only". MyJobQuote says that correctly installed lead flashing "can last for over 80 years", so lead in good order stays, while a split or raised piece gets renewed.

What happens next depends on what the survey shows. Joints that have opened are raked out and refilled; a stack with a few failed units gets those units replaced; one that leans or has cracked right through may need its top courses rebuilt. Each choice is shown to you in photographs before the price is written, and rebuilding is offered only when repointing would not hold.

Removing a stack altogether is a larger job than mending one. The Planning Portal states that "Building regulations approval will always apply when removing chimney breasts as they are part of the building's structure." Where the breast is on a party wall with the neighbour, the Party Wall etc. Act 1996 puts the duty on the building owner, who must serve a notice allowing the neighbour at least two months' notice ahead of cutting. A neighbour who has not replied after 14 days is treated as dissenting, and only then are surveyors appointed. Questions on that go to a party wall surveyor, not building control.

For rebuilding, repointing and capping a stack we have a longer explanation on our chimney repairs page.

Checked on a Coalway stack

  • Joints that have sunk or opened
  • Brick or stone faces that crumble
  • Flaunching cracked around the pots
  • Flashings and soakers where lead meets the slope
  • Pots leaning or loose in their bed
Fig. 3 Chimneys, drawn close

Callout 3 of 3

Eaves, soffits and the conservation areas nearby

Where the roof ends and the wall begins, the tiles overhang a gutter, the fascia board carries that gutter and the soffit closes the gap beneath. A fault in one part tends to spread to the next, so we check them together. Marley's figure for ventilating a cold roof beneath an HR underlay (which is not vapour-permeable) is "25mm along the length of the eaves for pitches of 15° or less; 10mm along the length of the eaves for pitches of more than 15°", which is why a soffit sealed shut can cause trouble in the loft.

Gutters have a rule of thumb from Brett Martin: a fall of "1mm for every 600mm". A run that holds a puddle or drips at its joints has dropped out of line, and its brackets need setting again before the board behind it takes the damp.

Soffits need care for another reason. The HSE says owners should treat a building from before 2000, or one refurbished before then, as though asbestos is present, and its list of locations includes AIB white soffit panels under the eaves. Most removal of asbestos insulating board falls under licensed work, and the job is passed to a firm that holds the licence, never done by us. We look first and do not disturb a board we suspect.

The closest entry on Historic England's list is Whitehill Farmhouse, Grade II (list entry 1299280, first listed 14 December 1983), a short way out of the village. Clearwell Conservation Area and Coleford Conservation Area are the nearest named areas, and Forest of Dean District Council holds their boundaries, so check its conservation area list for your street and check whether an Article 4 direction applies with Forest of Dean District Council. Roof windows and dormers come with planning conditions that our planning guide for roof windows sets out.

Building control is Forest of Dean District Council's own team, on 01594 812315, or a registered building control approver if you would rather use one. Fascias, soffits and gutters are the subject of our guttering, soffits and fascias page, which covers replacement as well as repair.

What shapes a Coalway quote

Access
Ladders, a tower or scaffold, and whether the highway is involved
Condition
How much timber and lead lie beneath the faults
Covering
Matching tiles for a repair, or a new covering
Extent
A patch, a single slope or the whole roof

One written total price, never itemised.

Coalway roof questions answered

What makes roof tiles slip on a Coalway house?

A tile slips when the nail or peg holding it fails, when the batten under it has softened, or when the course around it has moved. We find which by looking along the courses from outside and by torch from the loft, where daylight or darkened timber gives the cause away. Photographs of the loose tiles and the battens beneath them go with your report, so the repair matches what actually failed.

Are the Clearwell and Coleford conservation areas close enough to matter for a Coalway roof?

Clearwell Conservation Area and Coleford Conservation Area are the nearest named areas, and both are Forest of Dean District Council's designations. Whether your own address falls inside either is for Forest of Dean District Council to say, so check its conservation area list. Ask the council too whether an Article 4 direction applies; one can withdraw permitted development rights across a defined area.

Can a Coalway roof be re-covered in a heavier material?

Yes, after a check. The Planning Portal says Building Regulations approval is needed once a new covering raises the loading on the roof by 15 per cent or more. Building Regulations, not planning, is where that question sits. Before anything is ordered we would want to see the rafters and hear from your building control body or a registered building control approver.

What does a Which? survey say replacing a few broken tiles costs?

In a Which? survey from November 2025, swapping one to six cracked or absent standard tiles came in at £75 to £400, excluding VAT. That is a UK-wide range, not a price for Coalway. Ours is a single total once the roof has been looked at, with scaffold included, sent in writing together with photographs of the tiles concerned and the timber beneath.

Could the soffits on my Coalway house contain asbestos?

If the house was built or refurbished before 2000, HSE guidance is to presume there is asbestos in it, and the HSE's list of locations includes AIB white soffit panels under the eaves. Most removal of asbestos insulating board falls under licensed work, which we pass to a licensed firm. We survey the soffit first and will not disturb a board we suspect.

How does a scaffold licence work on a Coalway road?

Before scaffold can stand on the highway, section 169 of the Highways Act 1980 requires a licence. Gloucestershire County Council lists its scaffolding licence at £145 for a minimum of 28 days, plus £36 for each extra 7 days, and asks for at least twelve calendar days' notice. We arrange the licence with our scaffolder, and scaffold is part of the written total. Allow for that notice period when you pick a start date with us.

Arrange a Coalway roof survey

Write or call with what the roof is doing, and we will survey it, photograph the faults and send one written total price.

10-year workmanship guarantee, in writing