01432 610152 Get a quote Call 01432 610152

Roofers in Bream

Verges, chimneys and flashings on Bream's cottage roofs, repaired from the ridge down.

Tell us the symptom and we will find the cause, show you photographs, then write the total price.

Get a free quoteCall 01432 610152

Where Bream roofs give way

  • Older cottages with weathered clay tile roofs and brick chimneys behind a flint wall
    Worn verge mortarCrumbled verge bedding lets rain behind the edge tiles and into the gable.
  • Slate roofs and chimney stacks along a red brick Victorian terrace
    Chimney lead that has splitA split flashing beside a brick stack sends rain down the flue wall.
  • Newer homes with grey concrete tile roofs along a curving estate road
    A listed inn in the villageRoof work on a listed inn needs consent before any tile moves.

Bream in the border country

Bream on a street map, with a dashed circle around the town and the nearest towns we cover. Tiles © Esri; map data © Esri, HERE, Garmin, OpenStreetMap contributors.

Bream roofs, verge to listed inn

Three checks on a Bream roof: the gable verge, the chimney and the listed walls

We work along a Bream roof from the gable edge to the chimney, then out to the listed buildings nearby, keeping to the English rules and naming what the council has to be asked first.

A drawn cut-away section through a Herefordshire border house: the front of the main roof is cut open to show the rafters, underlay, battens and slates, beside a black-and-white timber-framed gable. Numbered, from the ridge down: 1 Gable verge; 2 Chimney and lead; 3 Listed walls.

Fig. 1 Bream section: gable verge, chimney with lead, and a listed wall, numbered 1 to 3.

Callout 1 of 3

Verges and shared walls on paired cottages

Our survey starts at the gable end. The Victoria County History of Gloucestershire (1996) records that "Between 1840 and 1880 some cottages, several of them in pairs, were built on the former encroachments around Bream's Eaves". A page of history cannot tell us what covers a given Bream house today, but the shape of a pair is familiar: a verge, the sloping edge of the roof beside a gable wall, closes each end, and the two roofs meet along the wall between them.

The verge is read first. We check whether the covering's edge has crept past the wall, whether the bedding mortar has crumbled and whether edge tiles rock when pressed. Where a verge has an undercloak, the strip of slate or board beneath the edge tiles, we check that too. Mortar can still be used. BS 8612 is the specification for dry-fix verge and ridge systems, which hold the edge with clips and screws, and Marley notes that installing to BS 5534 is not a legal requirement while the 2015 amendments ended reliance on mortar alone. Which method suits a given house depends on its tiles and its age, so the choice is made on the roof, not from a catalogue.

Next comes the abutment, where one roof runs up against the wall of the house beside it. Lead flashing is let into that wall and dressed down over the covering. Cutting into a wall the neighbour may share brings in the Party Wall etc. Act 1996, whose s2(2)(j) gives a building owner the right "to cut into the wall of an adjoining owner's building in order to insert a flashing or other weather-proofing of a wall erected against that wall". The owner serves the notice. A neighbour may consent in writing (s3(3)(a)); silence for 14 days counts as dissent (s5), and surveyors are appointed only then (s10). Any dispute under the Act in Bream is for a party wall surveyor; building control plays no part.

Up in the loft, we examine the wall plate, the timber the rafters sit on, and the rafter ends near the gable, because daylight or staining there shows a verge leaking before any ceiling does. Photographs of each corner go in the report. Re-covering both halves of a pair is covered on our pitched roofing page.

A loose edge tile

Does one loose verge tile mean the whole verge must come off?

Not always. A few loose edge tiles can be rebedded or refixed. If bedding has gone right along the edge, or the undercloak beneath has rotted, the whole verge is better done at once, and the photographs show which case you have.

A verge is the first place a gable roof tells you it is tired.

Fig. 2 The verge, drawn close

Callout 2 of 3

Brick chimneys, lead flashings and the breast inside

A chimney stands clear of the slope with every face exposed, so it ages faster than the roof around it. On a Bream stack we check the pointing, which is the mortar between the bricks, the flaunching, a sloping cap of mortar around the pot bases, and the pots themselves. Brick faces that flake let water into the stack, so every face gets a photograph for your report. Where lead has split or lifted, it comes out; sealant over the top is no cure.

Lead is the material where the stack joins the covering. A flashing is a lead strip tucked into a joint and lapped over the tiles; soakers are little folded sheets worked in under each course of the covering; the back gutter is the tray behind the stack that turns water round it. Royston Lead's table pairs thickness with use: Code 3 is "Recommended for lead soakers only", while Codes 4, 5 and 6 are listed for flashings. MyJobQuote says correctly fitted lead flashing "can last for over 80 years", a hedge and not a promise, so when lead fails early we look for the cause, such as movement in the stack, before we renew it.

Inside the house, a brown stain on a chimney breast, or damp plaster that comes and goes with the weather, tells us the fault may sit in the stack. We trace it from the loft upward and photograph the line it follows, so you can see where the water travelled before any price is written.

Removing a chimney breast is distinct from repairing the stack. The Planning Portal states that approval under the building regulations is always needed to remove a chimney breast, which forms part of the fabric that holds the house up. If the breast is built into a wall you share with the next house, s2(2)(g) of the Party Wall etc. Act 1996 covers cutting it away, and the notice must be served at least two months ahead of the first day on site (s3(2)(a)). Our chimney repairs page covers rebuilding, repointing and capping.

Words used at a Bream stack

Flaunching
The sloped mortar collar that holds the pots in place
Soaker
A small folded piece of lead slipped under each course
Back gutter
The lead tray behind a stack that turns water round it
Pointing
The mortar face of the joints between bricks
Flashing
A lead strip let into a joint and lapped over tiles
Fig. 3 Chimneys, drawn close

Callout 3 of 3

The New Inn, the cenotaph and nearby Pillowell

Last comes the wall, and with it the question of listing. The New Inn is listed Grade II (list entry 1213848, first listed 12 December 1953), and Bream Cenotaph is listed Grade II (list entry 1443965, first listed 14 March 2017). The same 1996 history says the cenotaph went up in the early 1920s at the road junction known in 1788 as St. Ann's Cross. It carries no roof, so it touches a roof job only if a ladder or scaffold has to stand beside it. For a listed building, LBCA 1990 s7 asks for consent before works that affect its architectural or historic character, and permitted development rights continue beside that duty, so Forest of Dean District Council is asked first. Our listed and heritage roofing page sets out how we work on protected roofs.

On a listed roof the first job is to record what is there. Photographs of every slope, the ridge, the verges and the lead go to the council with the proposal, so the officer can see what the new work would replace. Any tile that is still whole is refixed where it can be, and anything new is chosen to sit beside them in size, colour and fixing.

Pillowell Conservation Area, designated by Forest of Dean District Council, lies a short way from Bream. Whether any conservation area reaches your street is for the council's list to say, and our planning guide for roof windows sets out what a conservation area changes. Ask Forest of Dean District Council whether an Article 4 direction is in force on your road too, because a direction can take named permitted development rights away.

Building control is Forest of Dean District Council Building Control, on 01594 812315, or a registered building control approver. If scaffold must occupy the carriageway or footway, the licence comes under the Highways Act 1980 s169, with Gloucestershire County Council as the highway authority. We arrange the licence with our scaffolder; its lead time means the date is agreed at the survey.

What sets the price of a Bream roof job

Access
Whether scaffold must stand on the road or on private ground
Covering
Tile or slate, and how much of it can be reused
Lead
How much flashing is needed, and the code it calls for
Consents
Listing, a conservation area, or neither

One written total price, never itemised.

Bream roofs: verges, chimneys and listed walls

How is the verge on a Bream gable end held down?

Edge tiles can be bedded in mortar or held by dry-fix units that clip and screw down, a method BS 8612 specifies. Marley points out that BS 5534 is not a legal requirement, though the 2015 amendments ruled out leaving mortar as the sole fixing. Which route suits a house depends on its tiles and the state of the old bedding, so we look at the gable from the ladder and from inside the loft.

Do the listed New Inn and cenotaph affect roof work elsewhere in Bream?

Not directly, because listing attaches to the building named in the entry. The New Inn is Grade II (list entry 1213848) and Bream Cenotaph is Grade II (list entry 1443965), so roof work on either goes through consent under LBCA 1990 s7. A house nearby is a different case unless it is itself listed, and Forest of Dean District Council can check an address against the list. Scaffold and access near a protected building still need care.

Which conservation area is near Bream, and does it reach my street?

Pillowell Conservation Area is the one Forest of Dean District Council has near Bream. Whether it, or any other, takes in a given street is a question for the council's conservation area list and map, so check your own address before you alter anything the street can see. Forest of Dean District Council also knows whether an Article 4 direction is in force, and a direction can remove named permitted development rights from a defined area.

Does taking out a Bream chimney breast need building control?

Yes. The Planning Portal states that approval under the building regulations is always needed to remove a chimney breast. Where the wall is one you share with a neighbour, the Party Wall etc. Act 1996 also applies: the notice has to be served at least two months before a breast is cut away (s2(2)(g), s3(2)(a)). Forest of Dean District Council Building Control, on 01594 812315, or a registered building control approver deals with the approval.

What does scaffold on a Bream road involve?

Putting scaffold on the public highway means holding a scaffold licence (Highways Act 1980 s169). Gloucestershire County Council's list from 1 April 2025 gives £145 for a minimum of 28 days, then £36 per 7 days to extend, and asks for notice of twelve calendar days or more. We arrange the licence with our scaffolder, and the scaffold travels inside the single price we put in writing.

What lifespan can lead flashing reach on a Bream chimney?

MyJobQuote says correctly installed lead flashing "can last for over 80 years", which is a hedged claim and no promise. Royston Lead's table lists Code 3 as "Recommended for lead soakers only" and Codes 4, 5 and 6 for flashings, so thickness matters as much as age. A flashing that fails early points to movement in the stack or to poor dressing, and we look for that cause before renewing the lead.

Start your Bream survey at the verge

Describe the verge, flashing or chimney that worries you, and our survey will lead to a price in writing.

10-year workmanship guarantee, in writing