A tiled or slated roof needs a weathertight top edge. The ridge runs along the apex, the hips run down the sloping corners where the roof is hipped, and the verges close the roof along each gable. All three stand in the open, take the weather from every direction, and rely on small pieces held in place by mortar or by fixings.
When one of them fails, the signs can be plain from the garden. A ridge tile sits crooked, a length of pointing has dropped into the gutter, a cap is missing after a gale, or a verge tile has lifted at the gable. Left alone, a gap at the top lets rain onto the timbers below and into the loft.
The sections that follow explain what each part is, how a mortar ridge is rebedded, when dry-fixing is the better repair, how verges are put right, what published sources say about cost and which rules govern the work in England and in Wales. For other repairs to a roof, see our roof repairs page.
Ridge, hips and verges: the lines at the top
The names are worth knowing, because a quote for ridge tile repairs may cover any or all of them.
| Part | Where it is | What holds it |
|---|---|---|
| Ridge | The apex, where the two main slopes meet | Ridge tiles on a bed of mortar, or dry-fixed with fittings |
| Hip | A sloping corner, where the roof is hipped | Hip tiles, fixed in the same two ways |
| Verge | The sloping edge beside a gable wall | Edge tiles pointed in mortar, or dry-verge units fixed down |
Start with this: none of these parts is covered by the roof's main waterproofing, the underlay beneath the tiles. They are the cap on a seal, and they have to shed water themselves. Beneath a mortar ridge sits a bed of mortar, which is the bedding, and beneath that the tops of the last courses of tiles.
The second is that they fail for different reasons. A ridge cracks as the roof moves, a hip loosens at its foot, and a verge suffers where wind lifts the edge of the roof. A repair that fits one may not suit another, so a survey looks at each separately. A ridge that looks fine from the road can hide cracked bedding along the far side, which is why the check includes the line as well as the tiles.
Storm damage can show here, as blown or lifted tiles along the apex, and our guide to a ridge tile blown off covers that case.
Rebedding a mortar ridge
Rebedding means taking the ridge tiles off, clearing the old mortar, and laying them again on a fresh bed. It is the repair for a ridge whose pointing has cracked, whose tiles have loosened or whose mortar has crumbled away. The usual sequence is:
- Lift the ridge tiles and set them aside, keeping any that are sound.
- Scrape off the old mortar and clear loose debris from the top courses.
- Lay a fresh bed and set the tiles along a straight line.
- Point the joints and clear the roof of mortar droppings.
On a rebedded ridge, mortar is not left to do the job on its own. Marley says that "Installing to BS 5534 isn't required by law", and that since the 2015 amendments, mortar "could no longer be relied upon as the only means of securing the roof covering". Mortar is not banned. The repair adds mechanical fixing to the bedding so that a ridge tile does not depend on mortar alone.
The standard in question is BS 5534:2014+A2:2018, which is current.
Fallen pointing in the gutter, a ridge tile that rocks when pressed and daylight at a joint are the common signs that rebedding is due. If you can see a crooked ridge from the road, it is better dealt with before the next gale loosens a whole length. The Marley note on fixing requirements explains the standard in more detail.
The dry ridge fold: when dry-fixing is the repair
A dry ridge replaces the mortar bed with mechanical fixings, so the ridge tiles are held by fittings and not by mortar alone. BS 8612 covers dry-fix, and a dry verge works on the same principle at the gable, with edge units fixed down in place of a mortar bed.
For a repair, the table sets out the differences between them:
| Question | Mortar bedding | Dry-fixing |
|---|---|---|
| What holds the tile | A mortar bed, plus fixings | Fittings fixed to the roof |
| How it fails | Cracks and crumbles | A fitting works loose or a piece breaks |
| What the repair is | Rebed and re-point | Replace the piece or refix the line |
Where only a short stretch of an existing mortar ridge has failed, rebedding that stretch can be the repair. Where the mortar has failed along the whole length, or the same stretch keeps coming loose, converting to dry-fix is a repair option worth pricing, because it removes the part that keeps failing.
Appearance counts. A dry ridge looks different from a mortar one, which matters on an older or listed house, and our guide to repairing roofs on older Hereford homes deals with matching. Our post on dry ridge or mortar on Hereford roofs sets out the comparison further. Whichever is chosen, the system's own data sheet decides the fixings, and you can ask to see it. A dry system that is fitted to its data sheet, with the fixings it names, is what the standard has in mind.
Verges: pointing, edge tiles and the gable
The verge is the roof's edge along a gable wall. The edge tiles overhang or sit on the gable, and the gap beneath them is closed with mortar or with a dry-verge unit. It is an exposed line, because the wind meets the edge of the roof there before it meets anything else.
The faults to look for from the ground are:
- mortar that has cracked, shrunk or fallen away from under the edge tiles
- edge tiles that have shifted, lifted or slipped towards the gutter
- dry-verge units that have lifted or lost a fixing
- streaking on the gable wall below, from rain that has run down its face
Repairs follow the fault. Cracked pointing is raked out and made good, loose tiles are rebedded or refixed, and a broken unit is replaced. If the edge tiles are sound but the mortar has failed, the work stays small. If the verge timbers behind the tiles have rotted, they have to be dealt with before anything is laid back.
A gable is a high place to work from, and a ladder is a poor platform for a run of edge tiles. A tower or scaffold is the likely access, and our guide to ladders, towers or scaffold explains the options.
Where a verge meets a higher wall, the lead that seals the joint is part of the same repair. Mortar for any pointing is matched to the existing work in colour, so a repaired verge blends in when seen from the lane.
What a ridge or verge repair costs
Ridge and verge work varies with the length, the height and the method, so a published range is a guide and never a price. The figures below come from other publishers' UK surveys.
- Which? (November 2025 survey, ex VAT) gives £80 to £300 for one new ridge tile along the top of the roof.
- MyJobQuote, on a page dated 1 October 2026, says the average ridge tile replacement in 2026 costs between £225 and £550.
- Checkatrade (June 2026, ex VAT) puts ridge tile repairs at £50 to £70 per metre, which is a rate, not a total.
The three figures differ because they measure different jobs: one new tile, a replacement and a rate per metre. They should not be added together or multiplied out.
What sets the price of a ridge or verge repair:
- the length of ridge, hip or verge that has failed
- whether the tiles are rebedded in mortar or converted to dry-fix
- how many tiles are cracked and need replacing, rather than reusing
- how high the roof stands and the access it needs
- the state of the timber beneath the tiles
You are shown photographs of each fault before work starts, and the price is one total in writing. It is worth checking that any quote you compare says whether VAT and the scaffold are included. Photographs of the finished ridge and verge go to you as well, so the result can be compared with what was there before. A ridge repair that comes up inside a larger job, such as a re-roof, is priced within that job's single total.
England and Wales: what applies to ridge and verge work
Repairing a ridge or verge is small work, but a few rules apply in England and in Wales, and they differ.
- In England, the Planning Portal says no Building Regulations application is normally needed where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" are affected, so a ridge repair sits well inside it. Re-covering the whole roof does not.
- In Wales, the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval." For work beyond a ridge or verge repair, ask the council's building control service or a registered building control approver.
- A listed house must have consent ahead of any work altering its special character: under section 7 of the 1990 Act in England, and under sections 88 and 89 of the Historic Environment (Wales) Act 2023 in Wales.
Ridges and verges are also where wildlife settles. Section 1 of the Wildlife and Countryside Act 1981 targets the person who intentionally harms a nest that birds are using or building. Bat roosts are protected too, and GOV.UK includes roof repair in its list of work that may disturb bats. A bat licence is a matter for Natural England in England and for Natural Resources Wales in Wales. A nest or a bat found as a ridge tile comes off pauses the job until the next step is clear, and you are told what was found.
