Every pitched roof has a ridge, the high line where its two sloping sides join, and the ridge tiles are the curved or angled tiles that cap that join. For a long time they were bedded on mortar, a mix of sand and cement laid in a bed under each tile. Dry ridge systems fix the tiles mechanically instead, with a batten, clips or screws and a strip that closes the gap, and no mortar bed.
People in Hereford, Leominster and Kington ask which is better, and a fair answer has to start by saying that mortar is not banned. Marley, a tile maker, makes that point plainly, and so does the wording of the standards. The change is that mortar on its own can no longer be treated as what holds the ridge on.
This guide takes the two finishes in turn, then the standards, then the fold that a dry ridge strip makes over the top of the roof, then how a mortar ridge fails and what hips and verges share with it, and ends on published costs. A re-roofing rule that changes at the border is labelled with the country it covers. Our pitched roofing service covers all of it.
Two ways of finishing the top of a roof
A mortar ridge has each ridge tile bedded in mortar along the crown of the roof, and the joints between the tiles are pointed. It looks solid and is repaired by rebedding. Hip tiles, which cap the sloping outside corner between two roof planes, can be finished the same way.
A dry ridge replaces the bed with fixings. A batten is fixed along the ridge, the ridge tiles are held down onto it with clips or screws, and a strip is laid under them to close the gap and keep the weather out. Makers' systems differ, so the exact parts depend on the product chosen and on its data sheet.
| Point | Mortar-bedded ridge | Dry ridge |
|---|---|---|
| How the tiles are held | Bedded in mortar, with mechanical fixings added | Fixed down to a batten with clips or screws |
| What closes the gap | The mortar bed and pointing | A strip laid under the ridge tiles |
| What repair means | Rebedding and repointing | Refixing tiles and replacing the strip |
| Standard it refers to | BS 5534 for mechanical fixing | BS 8612 for dry-fix |
On a Herefordshire roof of clay or concrete tiles, either finish can be right. The choice depends on the tile and on the state of the ridge timber beneath. A Hereford roof may also have hips and a verge or two to deal with at the same time.
What BS 5534 and BS 8612 say
BS 5534:2014+A2:2018 is the current edition of that standard, and BS 8612 covers dry-fix systems. On whether BS 5534 is the law, Marley says "Installing to BS 5534 isn't required by law".
What the standard did change is how ridges are fixed. Marley adds that the 2015 amendments made it clear that mortar could not any longer be the sole means of securing a roof covering. That is a statement about fixing, and not a ban. A bedded ridge that is also fixed mechanically still sits comfortably with it, and so does a dry system that follows its maker's data sheet.
Three points follow for an owner:
- A roofer who re-beds a ridge in mortar alone, with nothing mechanical holding the tiles, is working in the way the standard moved away from.
- A roofer who calls a mortar ridge illegal is overstating the rule, since BS 5534 is not law.
- A roofer who says a dry system must be used should be asked to show the standard or the maker's data sheet that says so.
BS 5534 is not the only document in play. The tile maker's data sheet matters as much as the standard on a given tile, so we read it before choosing either finish, and we ask the same of anyone else who quotes. Our guide to what BS 5534 means for the tiles on your roof covers it at greater length.
The dry ridge fold, and what to ask of it
The fold is the part of a dry ridge that people do not see. In a dry ridge, a strip that some makers supply as a roll is laid along the crown of the roof and folded over the ridge, so that each side lies down onto the top courses of tiles. The ridge tiles sit above it and are fixed through to the batten. The fold closes the gap between the two slopes while letting the tiles move a little, and because it lies under the ridge tiles it is the last thing anyone sees once the job is finished.
Because the fold is hidden, the quality of the work is judged by what was done before the tiles went on. These are the points worth asking about:
- Is the batten fixed to a sound ridge board or the rafter ends, and not to rotten timber?
- Does the strip lie flat on the top courses, with its edges clear of the gutter line of the ridge tiles?
- Are the fixings the ones the maker names for that system, at the spacing it gives?
- Does the roof beneath still have its ventilation, so the system is not closing an airway?
- Are the end tiles at the gable fixed, and how?
Photographs matter here. A ridge is high and out of sight, and a roofer who takes pictures before and after gives you a way to check what is now hidden under the tiles.
Systems differ from maker to maker, so we follow the data sheet for the chosen product and the standards that apply, and we say which ones in the written price.
How a mortar ridge fails, and what you can see
You can spot most ridge trouble from the lawn or the pavement, with a phone camera at full zoom. Look out for these signs:
- A line of crumbs or grit on the ground, in the gutter or on a flat roof below, which may be mortar from the bed
- Gaps or dark lines between ridge tiles where pointing has dropped out
- A ridge tile that has slipped, tilted or sits at a different height from its neighbour
- A ridge that is no longer in a straight line along the skyline
- Daylight or damp in the loft near the ridge board
After a gale, a tile on the lawn is an obvious sign, and a ridge that looks normal from below can still have loose tiles. If you suspect storm damage, our guide to ridge and verge repairs explains the rebedding and the dry-fix repair.
The fix depends on what has gone wrong. Loose pointing may need only repointing. Tiles that have lost their bed need rebedding and a mechanical fixing so that the repair meets the standard. A ridge whose timber has rotted needs the timber seen to first. A roof with a failed ridge and a tired underlay is the case that tips a repair into a bigger job.
We climb to the ridge safely with the right access, photograph each problem and give you pictures of your own roof. Repairing wins on value if the remainder of the covering is in good order.
Hips, verges and what a re-roof sets off
The ridge is one of three places where mortar traditionally closes the top of a roof. The others are hips and verges. A verge is the sloping roof edge that runs up beside a gable wall, and a traditional verge is bedded and pointed in mortar. Dry verge systems replace that mortar with clips and a cap, and Herefordshire gable ends, whether on a timber-framed house or a brick-built semi, meet the same question. Our guide to dry verge systems on gable ends sets out the parts.
A re-roof can include the ridge, the hips and the verges, and what a re-roof sets off varies with the country:
- For England, the Planning Portal normally asks for no application when a re-roof touches under 25 per cent of the building envelope and under 50 per cent of the roof.
- The Portal adds that a covering which "increases the weight of the roof covering by 15 per cent or more" needs approval, again in England.
- For a Welsh address the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval."
For a Welsh address, including Monmouthshire and Powys, we ask the council's building control team or a registered building control approver before starting. For an English address in Herefordshire, Herefordshire Council Building Control is on 01432 261938.
Mending a ridge by itself counts as repair and not as a re-roof. A listed or period roof in either country may need consent whatever the thresholds, and for that we send you to our listed and heritage roofing service.
What a ridge costs, as published
Three published sources give figures for ridge work. They are national, dated and not specific to Herefordshire.
Checkatrade's roof repair rates (June 2026, excluding VAT) list ridge tile repairs at £50 to £70 per metre. The unit is the metre, and we do not turn that rate into a total here, because a ridge's length depends on the house. A hip adds its own length. A long terrace and a small bungalow differ a great deal, and so do a roof with one hip and a roof with four.
| Job | Figure as published | Source and date |
|---|---|---|
| A new ridge tile | £80-£300 | Which?, November 2025, excluding VAT |
| Ridge tile replacement | Between £225 and £550 on average | MyJobQuote, October 2026 |
What moves the total on a real roof is a short list, and none of it can be seen from the ground. The length of the ridge and the hips, how far the roof is off the ground, whether the old bed has to be cleaned out, the tile type, and the state of the timber under the ridge all matter. A roof that needs a scaffold costs more to reach, and the single written total allows for whatever scaffold is needed.
After a survey you are given one written total, with the photographs behind it, and when the work ends the site is cleared and the old mortar and broken tiles have gone.
