01432 610152 Get a quote Call 01432 610152

Pitch limits

Roof pitch limits for tiles and slates, product by product

Each tile and slate range has a lowest slope it may be laid on. This guide sets out Marley's published minimums product by product, then the slate conditions, and where to look for your own.

Horizon Roofing Hereford 9 min read

Pitch means how steeply a roof rises, counted in degrees above flat. A steep slope drops rain off the covering quickly. A shallow one holds it, lets wind push it up the laps and gives it longer to find a gap. That is why each covering comes with a lowest pitch below which it should not be laid, and why a new covering cannot simply be chosen for its looks.

Marley puts the reason in one line: every tile and slate has a minimum roof pitch "in order to protect the roof from water penetration". The figure is set by the maker for each product, so it changes from one range to the next. Two tiles that look alike from the garden can have limits many degrees apart.

We start every re-roofing survey by measuring the existing pitch and naming the covering on it. The sections below give Marley's figures for its clay and concrete ranges, the sentence Cupa publishes for natural slate, and what to do when your roof carries something that is in neither table. They cover both sides of the border, and the one place where the rules differ is marked England or Wales in the sentence. The wider picture is on our pitched roofing page.

What a minimum pitch is protecting

On a tiled or slated roof the covering is not watertight on its own. Rain is shed by each course lapping over the one below it, and by the slope carrying it away before it creeps sideways or upwards. Lower the slope and the overlap has to work harder. The maker tests a product, decides the lowest angle at which it still sheds water, and publishes that as its minimum pitch.

Marley adds that some tiles and slates "incorporate design features allowing them to be laid at a low minimum pitch", and that low pitches can be found on extensions where the angle of the roof is limited by obstructions such as second floor windows. A shallower extension roof therefore needs a covering with a low figure of its own, not a copy of the main roof's tile.

Three things are worth keeping apart when you read any pitch table:

  • the pitch of the rafters, which is the angle of the structure under the covering
  • the minimum for the product, which is the maker's figure
  • the extra conditions on that figure, such as the length of the slope, the lap or how exposed the site is

A roof can meet the first two and still fail the third. A table in a brochure or on a web page is a summary, and the sheet for the exact product is the document that carries the conditions. We therefore ask for the data sheet, never only the table, and we put the product name and its figure next to the measured pitch in the survey notes.

That written comparison is also what you see in the photographs we take of the roof, so the figure and the slope sit side by side on paper before any price is given.

Marley clay tiles, product by product

Marley's table gives five clay products. The names are product names, not regions, so a tile called Canterbury says nothing about where it was made or where it suits.

Marley clay tiles: minimum pitch as published
ProductMinimum pitch
Canterbury40°
Ashdowne35°
Hawkins30°
Acme Single Camber30°
Lincoln (a pantile)15°

A pantile is a clay tile with an S-shaped profile that laps sideways into its neighbour. Lincoln is the one product in this range with a figure of 15 degrees, well below the other four, which sit between 30 and 40.

The spread matters on a re-roof. A house at 32 degrees can take Hawkins or Acme Single Camber, but not Ashdowne or Canterbury. Choosing a tile for its colour first and checking the slope afterwards is how a roof ends up with a covering that sits below its limit, and the mistake only shows once the first winter has tested the laps.

These five are Marley's alone. Other makers publish their own tables, and the figures are not interchangeable: a similar-looking clay tile from another maker needs its own data sheet read. Where the old tiles are already on the roof and only a few have failed, the question is different, because matching the existing tile may matter more than choosing a new range. Our guide to what pitch clay tiles need deals with the clay question on its own.

Marley concrete tiles, product by product

Marley lists eleven concrete products, and the range of limits is wider than for clay. Where Marley writes "(Smooth)" beside a figure, the figure is for that finish, so read the data sheet to see which one your tile is.

Marley concrete tiles: minimum pitch as published
ProductMinimum pitch
Plain35°
Edgemere17.5°
Modern / Duo17.5° (Smooth)
Double Roman22.5° (Smooth)
Mendip15° (smooth)
Mendip 12.512.5°
Ludlow Major22.5° (Smooth)
Ludlow Plus22.5°
Wessex15°
Anglia25° (Smooth)
Ashmore22.5°

Two products show how far apart the numbers sit, and that is why a brochure photograph cannot stand in for the figure. Marley's Plain concrete tile asks for 35 degrees, close to the steepest clay figure above. Mendip 12.5 goes down to 12.5. A roof that suits one is far too shallow for the other, even though both are concrete.

Read the table as a shortlist rather than a menu. A roof at 20 degrees rules out Plain, Anglia and the 22.5 degree products, but leaves Edgemere, Modern / Duo, both Mendips and Wessex available on pitch alone. Weight, appearance and the tile already on the house then narrow that further, and the fixing method for the chosen tile has to suit the slope as well. Ludlow is a product name here. Our guide to what pitch concrete tiles need covers the same figures for owners who only want the concrete answer.

Natural slate: one sentence with conditions

Slate does not work from a product list in the same way, because the limit depends on how the slates are laid. Cupa, a slate supplier, publishes the sentence we work from: BS 5534:2014+A2:2018 "also indicates that the minimum roof pitch for natural slate is 20 degrees in the case of a project situated in an area with moderate exposure and with a slate 500mm long and a 115mm overlap".

Read that slowly, because every clause is a condition:

  • 20 degrees applies at moderate exposure, not on every site
  • the slate is 500 mm long, and a shorter slate changes the answer
  • the overlap, called the head lap, is 115 mm

Cupa also says the head lap comes from the pitch, wind uplift and exposure to driving rain, and that on lower pitches and more exposed sites wider slates are used and the lap is increased. It adds that hook fixings, which hold a slate by a hook over the batten instead of a nail, cannot be used on any pitch under 25 degrees.

For stone tiles and tilestones, the sandstone slates of Herefordshire's traditional stone roofs, no minimum pitch appears in either maker's table. SPAB, which advises on traditional buildings, notes that traditional Welsh slate and stone roofs are "predominantly double-lapped", so the supplier's advice and the existing roof's own history are the guide. If one stone is cracked, our guide to swapping one cracked tile may help.

Measuring your own pitch from the ground or the loft

You do not need to go on the roof to get a usable figure. Two safe routes:

  1. In the loft, hold a spirit level or a phone with an angle app against the side of a rafter and read the angle off the screen.
  2. From the ground, stand square to the gable end and compare the slope of the gable's top edge against a plumb line or the phone held at arm's length.

A pitch can also be checked with a tape. Measure the horizontal run and the vertical rise of the slope and compare them. The rise for each metre of run grows quickly with the angle:

Rise for each metre of horizontal run
PitchRise per metre of run
15°about 0.27 m
22.5°about 0.41 m
30°about 0.58 m
40°about 0.84 m

Take the reading on the rafter, not on the tile surface, because a thick slate or tile can sit slightly differently on the batten. Take two or three readings along the slope, because older roofs sag, and a slope that reads 30 degrees at the eaves can read less near the middle.

With the angle and the maker's name, the data sheet tells you whether a product is allowed on that slope. If the maker is unknown, we compare the shape and fixing of what is on the roof against the ranges before naming a replacement, and we tell you when the maker cannot be identified from the roof alone. Where it is a close call, the lower-risk choice is the tile with the larger margin over the measured pitch.

When a new covering brings other rules in

Changing the covering from one product to another can trigger rules beyond pitch. The border matters here, so each rule below carries its side.

  • In England, the Planning Portal gives a trigger for Building Regulations approval: a change of covering that leaves the roof heavier "by 15 per cent or more". Approved Document A, in paragraph 4.4, calls an increase of "more than 15%" a significant change in roof loading. This is a Building Regulations matter, not planning permission.
  • In Wales, the Welsh Government says that re-roofing "In most situations, this work will need Building Regulations approval", and that changing to a different material, "for example, slate to tiles", means approval under the Building Regulations "is likely to be needed" to look at the structure, the fire safety and the energy performance of the building.

A change from slate to tile can raise the weight question, and it is also a pitch case, because the tile's minimum may be higher than the slate's. A roof at 20 degrees can carry slate in the right conditions, but it cannot carry Marley's Plain tile at 35 or Anglia at 25.

Where the answer is not clear, we ask building control for the side of the border the house sits on, either the council or a registered building control approver, before pricing. The written price is one total and follows the survey, so the pitch and the covering are settled before a quote is.

Pitch limits: questions answered from the data sheets

Can I use a tile below its published minimum pitch?

Not as a way round the limit. The figure is the maker's lowest angle for that product, and the data sheet can add conditions on top. If the slope is below it, the choice is a product with a lower figure, or a change to the roof structure. We check the sheet before a tile is named.

Why is the pitch of a Hereford extension lower than the main roof?

Marley notes that low pitches can be found on extensions because obstructions such as second floor windows limit the angle. A shallower extension roof therefore needs a covering with a low published minimum, not a copy of the main roof's tile. We measure both slopes before we choose.

Does a steeper roof always allow any covering?

No. Pitch is one condition among several. Weight, fixing to BS 5534, the exposure of the site and, for slate, length and head lap all apply. A steep roof clears the pitch test for most products, but it still has to carry the new covering and hold it down.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing