In brief
The minimum pitch depends on which clay tile is on the roof. In Marley's published table, its Canterbury needs 40 degrees, Ashdowne 35, Hawkins 30, Acme Single Camber 30 and the Lincoln pantile 15. These are product names, not regions. The figure is a floor set by the maker, and the tile's own data sheet is the one to follow. Natural slate has a limit of its own, and stone tiles are judged roof by roof on site.
Why each clay tile has its own minimum
Pitch is the steepness of a roof, given in degrees above the horizontal. A steep roof gets rid of rain quickly. A shallow one lets water linger on the surface and gives a gust the chance to shove it sideways under the laps, so each tile has a lowest angle at which it is expected to keep the weather out.
That angle depends on the tile's shape and on how it overlaps its neighbours. A flat plain tile is laid in many overlapping courses, so every tile sits beneath two or three others, and it wants a steep slope to shed water fast. A pantile has a curved profile that channels the water, so it can sit on a flatter roof.
That is why a single answer would mislead. A roof of old hand-made plain clay tiles and a roof of modern pantiles can stand in the same street and need quite different minimum slopes. The tile is the starting point, so before we talk about repair or replacement we identify the covering, then take the slope readings on site and note each one.
Marley's published figures for clay
The table sets out the minimum pitch Marley publishes for its clay tiles. Marley's own advice is to read the product data sheet of the tile you actually have.
| Marley clay tile | Minimum pitch |
|---|---|
| Canterbury | 40 degrees |
| Ashdowne | 35 degrees |
| Hawkins | 30 degrees |
| Acme Single Camber | 30 degrees |
| Lincoln (pantile) | 15 degrees |
The names are product names and say nothing about where a tile was made. Herefordshire has a clay history of its own: in the county's building stone atlas, clay from the Raglan mudstones is named as the raw material of Herefordshire's brick, tile and pipeworks trades, which it calls famous. An old tile on a local roof may come from a works that no longer exists, so it may have no data sheet at all, and the roof has to be read from its slope, its laps and its condition. Reading the table is simple enough: the lower the number, the shallower the roof the tile can serve, and a pantile can go where a plain tile cannot. A tile with a high number is simply not made for a low roof.
How slate and stone differ, and how long clay lasts
Natural slate follows its own rule, which is not a clay one. Cupa, the slate producer, reports that BS 5534:2014+A2:2018 indicates a minimum of 20 degrees for natural slate on a project with moderate exposure, a slate 500 mm long and a 115 mm overlap, and that no hook fixing belongs below 25 degrees. Those conditions are part of the figure. For the full picture across coverings, see roof pitch limits for tiles and slates.
Stone tilestones are another matter, and each roof is judged on site, with the quarry consulted where a stone has to be matched, since a quarry can say what it can supply and how soon.
Clay lasts well. Marley reports that the BRE set a minimum life expectancy of 60 years for clay roof tiles, while HomeBuilding gives clay tiles 60 to 80 years. Treat both as typical ranges and not as promises. How long clay tiles last goes into what shortens that. For patch repairs, Checkatrade's June 2026 guide gives clay tile repairs at £110 to £160 per m², excluding VAT, for areas up to 3 m².
When the pitch decides the job
Pitch matters most when a covering is being changed. A tile laid below its minimum is a covering that will let water in, however good the workmanship, so before any re-cover we measure the slope and choose a tile that suits it, and we show you the readings. If the existing pitch is too shallow for the tile you would like, the answer is a different tile, not a hope that it will cope.
The rules for a re-roof split by nation.
- England: the Planning Portal sets its re-roofing bar at under 25 per cent of the total building envelope plus under 50 per cent of the roof affected, while a new covering weighing 15 per cent or more extra brings in approval too.
- Wales: gov.wales expects Building Regulations approval in most situations, and it picks slate swapped for tiles to illustrate a change of material.
Where clay is the choice, and the house suits it, clay plain tiles in Herefordshire describes the traditional option, and the pitched roofing page has the rest of the range.
