Where a tiled roof finishes against a gable wall, the slope ends in a verge. Nothing below it carries rain away, as a gutter does at the eaves, and it takes the weather side-on instead of from above like the ridge. Traditionally the last tiles are bedded in mortar over an undercloak, a strip of board, slate or fibre cement that holds the edge of the covering a little proud of the wall face. Mortar can crack and loosen as the years go by, so a verge is one of the first places we study from the ground.
A dry verge is the alternative. A cap or end tile is held to the roof with clips, screws or nails, and no wet mortar is needed to keep it there. Dry-fix parts are made to a published specification, BS 8612, and they sit beside the older fixing standard for tiles, BS 5534.
The sections below cover each part and its job, the two standards, how to read the verge you already have, what changes on an older house, and how the law differs between England and Wales. The wider range of tiled-roof work sits on our pitched roofing page.
What sits along the edge of a gable roof
A verge looks like one line from the road, but it is built from several layers, and a fault in any one of them shows up as the same loose edge. Before looking at clips and caps it helps to name what they replace or sit on.
| Part | What it is | Its job |
|---|---|---|
| Gable wall | The top of the end wall under the roof | Carries the verge and the rafter ends beside it |
| Undercloak | A strip of board, slate or fibre cement under the last tiles | Sets a straight edge and keeps tiles from tipping |
| Verge tile or cap | The finishing piece along the slope edge | Closes the gap between the covering and the wall |
| Fixing | Mortar in the old method, clips or screws in a dry system | Holds the edge against lift and slip |
The undercloak is the layer people forget, because it is hidden once the verge is finished. It decides how straight the edge runs and whether rain that gets under the cap drains back onto the roof or runs into the gable wall. A tired undercloak is a good reason to open the verge up, whatever system goes back on top.
A dry system changes only the fixing and the finishing piece. The wall, the rafters and the undercloak stay as they were, unless the survey finds one of them damaged, in which case we photograph it and show you before the price is set.
How clips and caps hold the edge
In a dry-fix verge each cap or end tile is secured mechanically to the batten or to the tile beside it, so the grip does not depend on a mortar bed bonding to the tile underneath. The details differ between makers, which is why the system chosen has to suit the tile it sits beside, but the sequence on the roof follows the same logic.
- Check and, where needed, renew the undercloak and the batten ends along the edge.
- Lay the verge-edge tiles to the line, with the cut edge or the made-for-purpose end tile facing the wall.
- Fix each cap or end piece with the clip, screw or nail the maker specifies, so it cannot lift in a gust or slide down the slope.
- Finish the junction with the ridge or the eaves course so the edge reads as one continuous line.
Where the verge meets a ridge, the two systems have to be made to work together. A dry ridge and a dry verge from the same maker are designed to meet, and a mortar ridge can meet a dry verge, but the join needs thought at the survey, not on the day. Our guide to what a dry verge is covers the vocabulary.
Because clips and screws can be reached, a dry verge can be inspected and a single cap replaced without lifting a run of bedding. That is a point of design, not a promise about how long any system will last, and the life of the clips is a question for the system's own maker.
What BS 8612 and BS 5534 say
Two standards sit behind the work. BS 5534 is the code that governs slating and tiling, including how the covering is fixed, and the edition in force is BS 5534:2014+A2:2018. BS 8612 is the specification for dry-fix, and the version listed by the British Standards Institution is current. Neither one is a statute.
Marley, the tile maker, says "Installing to BS 5534 isn't required by law". It also says the 2015 amendments to BS 5534 "made it clear that mortar could no longer be relied upon as the only means of securing the roof covering". That is a statement about relying on mortar alone, and it does not ban mortar. A verge bedded in mortar and also fixed mechanically is a normal way to build one, and a verge fixed with clips and no bedding at all is the dry route.
| Standard | What it covers |
|---|---|
| BS 5534:2014+A2:2018 | Slating and tiling, including fixing |
| BS 8612 | Dry-fix ridge, hip and verge parts, as a specification |
In plain terms, BS 5534 asks how the covering is held on, and BS 8612 gives the dry-fix way to a held-on edge. When we write a quote for a verge, it names which of the two routes is proposed, the tile it suits and what is being renewed under it, which lets you set it beside another firm's quote on equal terms. Our guide to what BS 8612 covers takes the dry-fix standard further.
Reading a verge from the ground
A first view needs no ladder. Stand at the far side of the garden, or across the road if it is safe and legal to stop there, and look along the gable edge, ideally with binoculars. The line should be straight, with the edge tiles sitting evenly and no daylight under them.
What a worn mortar verge can show:
- cracks that run along the mortar where it meets the tile
- a lip of mortar that has dropped onto the path or the lean-to below
- a dark line of damp on the gable wall under the edge
- an edge tile that sits lower than its neighbours, or has tipped outwards
- moss or a green stain where water has been held against the edge
What a dry verge can show:
- a cap that has lifted or slid out of line
- a clip or screw head visible where it should be covered
- a missing cap, with the undercloak showing
Either way, treat mortar on the ground as evidence. It tells you the verge has been losing material, and our guide to mortar falling from a verge explains what to do next. Do not walk on a roof to look closer. On a survey we climb with the right fall protection and photograph the edge close up, so the pictures show you what the ground view could not, and a loose cap or lifted tile is recorded with its position on the gable.
Older houses and stone-tiled verges
A dry verge is made to suit modern concrete and clay tiles in standard profiles. An older house needs more care, because the verge there was built for a different covering.
Stone roofs in Herefordshire are traditionally laid with local sandstone tilestones, and the stone atlas published by the county puts the St Maughans sandstones, with active permissions to work them in the Golden Valley area, at the head of its list of sources. In SPAB's description, Welsh slate and stone roofs "are predominantly double-lapped". A double-lapped stone verge has its own way of finishing the edge, with the stones cut and laid to suit the building, and a factory cap made for a concrete interlocking tile would sit wrongly on it. Where tilestones need replacing, SPAB advises that "Claims of unavailability or long delivery times should always be checked with the quarries".
On a house framed in timber, the black-and-white kind, the roof edge can sit close to old carpentry, and the verge may be where an old gable meets a later extension. The repair then follows how the house was put together, and a standard kit is only used where the covering is a standard tile. A stone-tiled verge is judged on the stones and the gable in front of us, so that work is described here in plain terms.
For clay plain tiles and concrete interlocking tiles, a dry verge can be fitted to the product the maker names. We survey the verge first and then say whether dry-fix suits it, or whether the existing detail should be repaired in the same style.
Approvals for a verge change, England and Wales
Changing a mortar verge for a dry one is part of re-covering, and the rules depend on where the house stands. They are the owner's to check, with our help at the survey.
- In England, the Planning Portal says no Building Regulations application is normally needed where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" is affected.
- In Wales, the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval."
- In England, Class C of the General Permitted Development Order 2015 takes in any other alteration to the roof of a house, and a house can normally be re-covered as permitted development.
- In Wales, Class C.2(a) of the 1995 Order says the appearance of materials must "so far as practicable match" the existing house, so a verge in a different style needs a check with the council.
Consent is needed as well for a listed house where the work touches its character: in England under section 7 of the Planning (Listed Buildings and Conservation Areas) Act 1990, and in Wales under sections 88 and 89 of the Historic Environment (Wales) Act 2023. In a conservation area, ask the council before altering how the roof edge looks, and ask whether an Article 4 direction applies to the house.
Whatever firm quotes, look on any quote for a statement of whether VAT and scaffold are included. A gable scaffold that takes up the footway needs a licence under the Highways Act 1980, and we arrange the licence with our scaffolder.
