01432 610152 Get a quote Call 01432 610152

BS 8612

What does BS 8612 cover?

BS 8612 is the British Standard for dry-fix. It deals with ridge, hip and verge fittings that are held by fixings and not bedded in wet mortar.

In brief

BS 8612 covers dry-fix systems for the edges and high points of a pitched roof: ridge, hip and verge. Dry-fix means the capping pieces are held on by mechanical fittings, with no reliance on a mortar bed. BSI lists BS 8612 as current. It sits beside BS 5534, which covers slating and tiling generally. Marley notes that installing to BS 5534 "isn't required by law", so the standards guide the work without being statute.

What dry-fix means at the top of a roof

Look at the very top of a pitched roof and you will see the ridge, the line of capping pieces where the two slopes meet. A hip is the same kind of line, but it slopes down an external corner on a roof with four faces, and a verge is the edge that follows the slope at a gable end. All three are exposed edges, and the wind pulls hardest on them.

The old way was to bed each piece in mortar and point the joints. Dry-fix swaps the bed for fittings that screw, clip or bolt the pieces down, with vented or sealed strips to close the gaps, so there is no wet mortar left to crack and drop out. BS 8612 is the specification those systems are made and fitted against.

Not every ridge needs the change. A mortar ridge that is sound and secured with a mechanical fixing is still a valid piece of roofing. Dry-fix is one route among others, and the choice turns on the tile, the pitch, how open the site is and the look the house calls for. A border cottage with an irregular line of clay ridge tiles is a different brief from a 1990s estate roof in interlocking concrete.

How BS 8612 sits beside BS 5534

Two British Standards come up together on tiled roofs, and they are easy to confuse.

  • BS 5534:2014+A2:2018 covers slating and tiling as a whole, as a code of practice: battens, underlay, nails and clips, and how the covering is held on. BSI lists it as current.
  • BS 8612 is the dry-fix specification for ridge, hip and verge systems. BSI lists that as current too.

Marley, the tile maker, says the 2015 amendments to BS 5534 made it clear that mortar "could no longer be relied upon as the only means of securing the roof covering". That is not a ban on mortar. It means a ridge, hip or verge needs a mechanical fixing as well, and a dry-fix system built to BS 8612 supplies one as part of the kit.

Neither standard is BS 6229:2025, which belongs to flat roofs with flexible waterproof coverings. On a house with a pitched main roof and a flat extension, each roof is therefore judged against a different document, and a survey should keep the two apart.

Questions worth putting to any roofer

A quote for ridge work should say what is going on the roof, not just that something is. Here is what to ask, and we put each answer in writing with the price.

  • Is the ridge being bedded in mortar with a mechanical fixing, or fitted as a dry-fix system?
  • If dry-fix, is the system made for the tile that is already on your roof, and what colour will the fittings show from the street?
  • How are the ends dealt with where the ridge meets a chimney, a verge or a hip?
  • At the verge, will it be a dry verge unit, or mortar with a fixing behind it?
  • Are the old pieces being reused, or replaced with new ones?

Answers differ between a plain tile roof and an interlocking one, because the ridge piece has to suit the tile beneath it. A system chosen from a catalogue without looking at the roof is a guess. For the verge side of this, read what a dry verge is and the dry verge systems guide.

What it costs and which rules apply

Two named guides give ridge figures. From its November 2025 Trusted Traders survey, Which? puts a new ridge tile at £80 to £300, excluding VAT. MyJobQuote gives an average of £225 to £550 for ridge tile replacement. Both are general ridge numbers. A dry system adds fittings, and the length of run sets the total, which reaches you as a single written sum after the survey.

A ridge or verge job may not count as re-roofing alone, but the border changes the rules, and listing or a protected area adds more.

  • England: the Planning Portal asks whether less than 25 per cent of the total building envelope is affected, and less than 50 per cent of the roof, before saying an application is normally unnecessary.
  • Wales: gov.wales begins its re-roofing guidance by saying approval under the Building Regulations will be needed in most situations, and under GPDO 1995 Class C.2(a) the appearance of new materials must so far as practicable match the existing.

For the wider work on the same roof, the pitched roofing page sets out where each job begins.

Related questions

Is a mortar ridge out of date now?

No. Marley says mortar can no longer be the sole fixing, which is another matter. A sound ridge with a mechanical fixing meets the same aim as a dry-fix one. Whichever route you choose, we photograph the ridge before the work and afterwards, which gives you a record of each stage.

Can BS 8612 fittings be added to an existing roof?

In principle, yes: a dry-fix system can replace a mortar ridge on a roof already built, provided it suits the tile. We check the tile type and the pitch on site and tell you if a system is the wrong match. The old bedding is cleared first and the waste is taken away.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing