01432 610152 Get a quote Call 01432 610152

Dry verge

What is a dry verge?

A dry verge closes the sloping edge of a gable roof with fixed fittings instead of a line of mortar. Nothing wet has to set, crack or fall out.

In brief

A dry verge is the finish along the rising edge of a gable roof when it is done with fittings screwed or clipped to the roof, not with a bed of mortar. The fittings hold the last tiles down and close the gap between tile and gable wall. BS 8612 covers dry-fix systems, for ridge, hip and verge alike. A dry verge has no mortar to crack, but it shows differently from a mortar one, and that matters on an older or protected house.

The verge, and what dry takes away

Where a house has a gable, the end wall climbs to a point beneath the roof instead of stopping at an eave. Along that wall the tiles finish at the verge, running up the slope on each side of the peak. It is exposed to wind from underneath as well as above, and it has to be sealed against rain without being tied so rigidly that it cannot move.

A traditional verge is made by bringing the last tiles a little past the wall, then bedding and pointing them in mortar along the wall's top edge. The mortar does two jobs at once: it fills the gap and holds the tiles down. When it cracks or crumbles, it does both jobs worse, and loosened pieces can fall to the ground. Our answer on mortar falling from a verge covers that failure.

A dry verge separates the two jobs. Fittings do the holding and a trim does the sealing, so there is no mortar to fail. The word dry simply means no wet trade is used to fix the edge.

How a dry verge is fixed

The parts differ from maker to maker, but the principle is common.

  • A verge unit, a cap or trim piece made to follow the edge, which covers the end of the tiles and the top of the wall
  • Mechanical fixings, screws or clips, driven into the batten ends or the structure below, so the unit does not depend on mortar
  • End closures that finish the unit at the ridge and at the eaves

BS 8612 is the British Standard for these systems, and BSI lists it as current. Marley, the tile maker, says the 2015 amendments to BS 5534 made it clear that mortar "could no longer be relied upon as the only means of securing the roof covering", which is why every verge, wet or dry, now needs a mechanical fixing in some form.

The detail we start from is the verge itself, because it sits on the skyline we check first. We photograph how the last course is held and what the wall below is doing, and a system is matched to the tile rather than picked from a brochure. The longer explanation is in the dry verge systems guide.

Dry or mortar: how the two compare

Neither is right for every roof. The comparison below sets out how they differ in practice.

A dry verge beside a mortar verge
PointDry vergeMortar verge
Holding the tilesMechanical fixingsMortar bed, with a fixing added
CrackingNo mortar to crackJoints open as the roof moves
AppearanceA plastic or metal trim lineThe traditional pointed edge
RepairReplace a unit or fixingRake out and repoint

The look is the real question on an old house, and it is easy to settle on the day by holding a sample trim against the existing edge before anything is ordered. A dry verge trim is a modern line along the edge, and on a cottage whose character is its irregular mortar, it can look out of place. On a newer roof it can be the cleaner answer. A mortar verge with a proper mechanical fixing behind it is still sound practice, and on a roof where the gable wall itself needs attention, repointing the verge at the same visit can be the sensible way to do it. We say which suits your edge once we have seen it.

What the law asks in England and in Wales

Changing the verge changes the outline of the roof, and the rules for that vary with the house and with where it stands. A new fitting along the edge is visible from the road, and consent follows what the building is.

  • England: the Planning (Listed Buildings and Conservation Areas) Act 1990 section 7 means works affecting a listed building need consent, so a dry verge on a listed house is put to the council first. England's Class C has no condition on matching materials.
  • Wales: the Historic Environment (Wales) Act 2023 sections 88 and 89 apply to listed buildings, and under GPDO 1995 Class C.2(a) the appearance of materials must so far as practicable match the existing, which a different verge trim could break.

On re-roofing, the Planning Portal asks, for England, whether less than 25 per cent of the total building envelope and less than 50 per cent of the roof is affected. For Wales, gov.wales says re-roofing needs approval under the Building Regulations in most situations. A verge alone is a small part of any roof, and we check with the council's building control service or a registered building control approver where it is unclear.

The pitched roofing page covers the wider roof.

Related questions

Will a dry verge look different from my current one?

Yes, it will. A trim or cap runs along the edge instead of a pointed mortar line. The effect depends on the system and its colour, which is chosen to suit your tile. On a listed or character house, we show the proposed fitting first and ask the council whether it is acceptable.

Does a dry verge mean I never need to look at the edge again?

No. No mortar remains to crack, but fittings and fixings are checked like any other part of the skyline. A survey every so often looks at the units, the fixings and the wall top beneath. Water running down the gable wall can still damage the masonry under a perfect trim.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing