01432 610152 Get a quote Call 01432 610152

Condensation

Spray foam and condensation risk in a roof

Foam is sold as a way to stop warm air escaping, yet it changes where moisture ends up. Here is how condensation forms in a foam-lined roof and what a survey looks for.

Horizon Roofing Hereford 9 min read

Condensation happens when warm, damp air meets a surface cold enough to turn that moisture into water. A house makes plenty of damp air: cooking, washing, drying clothes and breathing all add to it. In a traditional loft, some of that air drifts upwards, and the cold roof structure and a flow of outside air through the eaves carry it away before it does harm.

Spray foam changes the arrangement. The foam is applied directly against the roof covering or its underlay, so the timbers behind it sit in a space with little or no air movement, and the foam itself may stop moisture passing through. Whether that matters depends on the type of foam, how well it was applied, what sits behind it and how much damp air the house produces.

This guide explains how condensation forms in a foam-lined roof, how closed-cell and open-cell foam differ on moisture, what the ventilation standards say, how to read the warning signs, and what a survey measures. It is one of our guides within spray foam removal.

How condensation forms under a roof covering

The air in a warm room holds invisible water vapour. When that air reaches something cold, such as the back of a tile, a metal fixing or a corner of timber, the vapour can condense into droplets. The cold surface does not have to be wet from outside. The water arrives from inside the house.

An ordinary pitched roof with a loft is designed to cope. Air enters at the eaves, the underlay either lets vapour through or sits above an air gap, and the loft stays close to outdoor temperature. The timber stays cooler than the house but dry enough to be safe, because any vapour that reaches it is carried off before it settles.

You can spot the signs from inside the loft:

  • beads of water on the back of the covering or on nail tips
  • dark spotting or a white bloom on rafters and battens
  • damp patches in the insulation or around the hatch on a cold morning
  • a musty smell that does not clear

None of these proves a leak, and rain coming in looks different, tending to leave a stain below one particular point. Our guide to telling condensation from a roof leak covers the diagnosis from the repairs side. Cold weather makes the effect stronger, which is why winter mornings give the clearest evidence. What matters here is that the moisture comes from living in the house, so work on the outside of the roof cannot cure it alone.

Closed-cell and open-cell foam handle moisture differently

The Energy Saving Trust, in advice last updated on 26 October 2026, separates spray foam into two families. Where moisture is concerned, the difference between them is what counts.

What the Energy Saving Trust says about the two foams
FoamMoisture behaviour
Closed-cellNot vapour permeable, which it names as the main drawback
Open-cellThe more vapour permeable of the pair

On the timbers themselves, the Trust says foam sprayed straight onto the roof partially seals the timber, and that the resulting risk "should be much lower" with open-cell foam. Those words are hedged. They say the risk should be lower, not that it is nil, and they do not claim that rot has occurred in any particular roof.

The two outcomes are easy to picture. If moisture cannot pass through the foam, it has to stay in the air of the house or find another route out. If moisture can pass slowly through open-cell foam, it may reach the cold side and condense there, where the foam cannot dry it. Which of those happens in a given roof depends on construction details no leaflet can settle. Neither type is a substitute for a sound roof build, and neither removes the need to look at how the house makes and sheds damp air. Our guides to open-cell or closed-cell spray foam and whether open-cell foam is breathable look at each type in turn, and the survey guide shows how the type is identified.

What the ventilation standards ask for

Ventilation is the traditional answer to condensation in a cold roof, and the standards deal with it directly. BS 5250 is the code of practice on moisture in buildings, and it stays current while a review is under way. Approved Document C for England, dated 2013, meets the condensation requirement by pointing to Clause 8.4 of BS 5250:2002 and to BS EN ISO 13788:2002.

Marley, the tile maker, gives eaves openings where the cold roof has a high-resistance underlay, known as HR, which passes no vapour:

  • an opening of 25mm for pitches up to 15 degrees
  • an opening of 10mm for pitches above 15 degrees

For an air-permeable (LR) underlay under a well-sealed ceiling, Marley counts the 3mm of normal eaves construction as enough fortuitous ventilation, so long as the third-party certification terms are met in full.

Foam laid directly against the covering takes away the eaves gap and the air space those figures assume. That does not make a foam roof wrong, but it does mean a cold-roof figure cannot be carried across to it. A foamed roof is a different system, and whoever specified it should be able to show why it works. Where nobody can, a survey is the way to find out what the timbers are doing. We cover ventilation after the foam is out in our guide to loft ventilation after foam removal.

Signs that a foam-lined roof has a moisture problem

You cannot see the timbers behind the foam, so the evidence is indirect. What a surveyor looks for is a pattern: marks in one place suggest a local fault, while the same marks along the whole roof suggest moisture that has nowhere to go.

Inside the house, check ceilings and top-floor walls for mould, peeling paint or damp patches that return each winter. Check windows in the rooms below the roof for streaming condensation, which can show that the house itself is holding damp air.

In the roof void, the useful things to look for are:

  • foam that has lifted, cracked or pulled away from rafters
  • dark staining on any timber still exposed, such as the wall plate or the ends of rafters
  • damp or discoloured plasterboard where a ceiling meets the foam
  • rusty or stained fixings that pass through the foam

On the outside, slipped tiles, blocked gutters and failed flashings can produce a leak that looks like condensation, so those have to be ruled out first. A foam-lined roof that does leak is harder to diagnose because the foam hides the route that water takes. Whether any of this leads to rot is another matter, set by how long the timber stays damp. Take photographs on a fixed date each month through the winter, from the same spot, so that a change is plain to see on screen and not left to memory.

Cutting the damp air at its source

Whatever the roof is made of, less damp air in the house means less to condense. Some of that is within your control and costs little.

  • run the extractor fan in the kitchen while cooking and for a while afterwards
  • use the bathroom fan during and after showers, and check that it vents outside and not into the loft
  • dry washing outdoors or in a room with a window open where you can
  • keep furniture a little way from external walls so air can move
  • fit a vented tumble dryer hose to the outside, not a room

A fan that discharges into the roof void is a particular worry in a foamed roof. Warm, wet air blown into a space with little ventilation can condense on the first chilly timber in its path. During a survey we follow the duct from the ceiling and note where it ends.

These measures reduce the load but do not replace a sound roof build. If the foam is closed-cell and the roof has shown staining on exposed timber, the house may still be holding more moisture than the structure can shed. Cheaper steps first, then a decision about the foam on the evidence, is a sensible order, and we will tell you if a fan is all the house needs. It also keeps you from paying for work that a fan and a changed habit would have made unnecessary.

What a survey measures and what it cannot

A condensation survey on a foam-lined roof has three parts. The first is outside: the covering, ridge, verges, valleys, flashings and gutters, photographed, so that a leak is ruled in or out. The second is inside the house, looking at how damp air is produced and whether the extractor fans vent outdoors. The third is the roof void, where we photograph the foam, note its type and its condition, and take moisture readings at points we can reach.

There is a limit to this. A meter on the surface of the foam does not measure the timber under it. Readings taken at the wall plate, at rafter ends or through a small agreed opening are better evidence than a surface reading, and an opening is made only with your agreement, in a place that can be put right afterwards.

The outcome is one of three findings. The roof may be sound and the foam can stay. The roof may need extra ventilation or a change to how the house handles damp air. Or the foam may need to come out so the timbers can be inspected and the roof re-insulated. Whichever it is, the photographs come to you with a written total for whatever we advise. Our guide to surveying a foam-lined roof sets out the inspection in more detail.

If the answer is removal and new insulation, the target for the roof depends on the country. In England, AD L 2021 Table 4.3 sets 0.16 for a renovated roof, with 0.35 as the threshold, until AD L 2026 takes over on 24 March 2027. In Wales, Table 11.1 of the Welsh AD L gives 0.16, and not worse than 0.35 where 0.16 is not feasible, with a new edition from 4 March 2027.

Foam and condensation: your questions

Does closed-cell foam always cause condensation?

No. The Energy Saving Trust names a lack of vapour permeability as the chief drawback of closed-cell foam, which is a different thing from certain damp. Whether moisture builds up depends on how much damp air the house makes, how the foam was applied and what sits behind it. A survey reads those details on your own roof.

Can I stop condensation by adding vents to a foam-lined roof?

Not by vents alone. Cold-roof ventilation figures assume an air gap that foam applied against the covering removes. Better extraction in kitchens and bathrooms can reduce the damp air, and a survey will tell you whether the roof build also needs changing, and by how much.

How do I tell condensation from a leak in a foam roof?

A leak tends to leave a mark below one point and appears after rain. Condensation tends to appear along the roof in cold weather, including dry days. Because the foam hides the route of any water, we check the outside of the roof first to rule a leak in or out.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing