01432 610152 Get a quote Call 01432 610152

Foam removal process

How spray foam comes out of a Herefordshire roof, stage by stage

Removing spray foam is a sequence, not one big scrape. These are the stages we follow under a foam-lined roof, in the order they happen, and what you will see at each.

Horizon Roofing Hereford 9 min read

Spray foam is a liquid when it goes on and a solid when the job is finished, and it sets against everything it touches: rafters, battens, the back of the tiles, the underlay. Taking it off means working from the loft side, one slope at a time, and deciding at each step how much the roof beneath will stand.

The order matters more than any single tool. If the foam is lifted before anyone has looked at the roof, damage that was already there gets blamed on the removal, and damage the removal causes goes unnoticed. If the roof is made good before the timbers are seen, the repair covers up the evidence.

So we follow six stages: survey, preparing the loft, lifting the foam, inspecting what it covered, making good, and clearing up. The sections below take them in turn, with the points where England and Wales differ and a look at what third parties say removal costs. The wider job is set out on our spray foam removal page.

Stage one: a survey that starts at the hatch

Before anything is touched, we find out what we are dealing with. From the loft hatch and with a strong lamp we look at the foam surface, its thickness where the hatch and pipe runs show a cut edge, and where it stops at the eaves. We note whether the covering above is tile, slate or stone tilestone, whether there is an underlay, and whether the roof has a chimney stack, valley or roof window that foam has filled around. Details such as these decide where lifting can start and where it must be slow.

The most useful question at this stage is which kind of foam it is. The Energy Saving Trust names closed-cell and open-cell as the two main kinds, and they do not lift the same way. Our guide to open-cell and closed-cell foam explains the difference, and it helps you work out which one you have.

We also look outside. A walk around the house, a check of the ridge, verges, valleys and gutters, and photographs from the ground give us a record of the roof before the loft work begins. You then see the pictures, and afterwards you receive a single written total for the work.

What the survey cannot do is see behind the foam. Anything it covers stays unseen until it is lifted, so we say plainly in the survey what we have not been able to look at, and we say what we will do if something turns up.

Stage two: protecting the house and opening up the loft

Foam removal makes dust and offcuts, and a loft is a tight space. Before lifting begins, the work area is cleared of stored boxes and anything loose, and we lay sheeting over the floor and the hatch route. Wherever the joists are not boarded, we put down boards to stand on, because the ceiling below will not carry a person.

Lighting comes next. The loft is poorly lit at the best of times, and foam hides the places where we want to see clearly, so we bring temporary lamps. Any electrical cables that run along the rafters are noted before cutting starts, since a blade near a cable is a hazard rather than a nuisance.

Whether the work is done from inside only or also from outside depends on the covering. A roof with sound tiles that are bonded to foam may need a few lifted from outside so the foam can be reached from both sides. Scaffold, if it goes up, sits inside the quote. For a tower on the public road, the scaffold licence is the one thing here that we arrange with our scaffolder.

You will be asked to do three things before we start:

  • clear the space around the hatch
  • move cars away from the drive or the kerb in front of the house if scaffold is going up
  • tell us about anything fragile or stored in the loft that you want us to leave alone
  • let us know if the loft has a water tank, a flue or a boarded section, since each changes how we get around

Stage three: lifting open-cell and closed-cell foam

This is the stage everyone pictures, and it is the one that varies most. The two kinds of foam behave differently once they are set, so they are taken off differently.

How the two kinds of foam come off
FoamCharacter once setHow it is lifted
Open-cellSoft and spongyCut back from the rafters, then peeled and scraped from the covering side
Closed-cellFirm and rigidCut into sections and lifted away piece by piece

In both cases we work slowly near the underlay or the back of the tiles, because that is where the foam is most firmly stuck and where a hurried pull can tear a sheet or lift a tile. Each rafter bay is done in turn and the offcuts are bagged as we go, so the loft does not fill with loose foam.

Where foam has been sprayed onto felt or a membrane, expect the sheet to come away in places. We explain that in a separate guide to spray foam on felt and breathable membranes. Where it was sprayed onto bare tile backs, the concern is the tiles themselves, and a separate answer deals with removing foam without damaging them.

No one can promise that every tile or slate will survive the lift. What we can do is photograph any that break, tell you, and match replacements to the rest of the roof.

Stage four: reading the timbers the foam covered

Once a rafter bay is clear, the timber is visible for the first time since the foam went on. This is the moment the survey could not reach, and it is the reason we photograph before anything else is done.

The Energy Saving Trust notes that spraying onto the roof's underside partially seals the timber, but that the "risk should be much lower with an open-cell foam". We take that as a reason to look, not as a verdict either way. For each rafter and batten we check:

  • colour, because dark or grey patches mark wet timber
  • surface softness, tested with a probe at the ends and where the timber meets the wall plate
  • fixing nails, which rust where moisture has been present
  • staining on the back of the underlay or the tiles
  • any signs of insects or fungal growth

The findings go in three groups. Timber that is sound is left alone. Timber that is damp but sound is left to dry once the loft can breathe again. Timber that is soft or broken comes out, and new timber goes in alongside the old, which keeps the repair as small as the damage allows.

Every group is photographed before and after, and you see the whole set, labelled by rafter bay so that you can match each picture to a place in your loft. If the timber is worse than the survey could show, we stop and tell you before carrying on, and any change to the plan is agreed with you in writing before it goes ahead.

Stage five: making good, ventilating and insulating again

With the foam gone and the timbers read, the roof is put back in order. Slipped or broken tiles are replaced, torn underlay is renewed, split battens are swapped, and the loft is given ventilation again. Then the insulation goes back, sized for your side of the border. Our guides to roof repairs after foam removal and re-insulating after foam removal go into each in turn.

Approvals follow the nation the house stands in. Work that stays inside the loft is a different matter from work that lifts the covering, and building control, either the council or a registered building control approver, tells you which you have.

  • England: the Planning Portal says Building Regulations approval applies where a roof is re-covered with something 15 per cent or more heavier, and describes the lighter case as one where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" are affected.
  • Wales: the Welsh Government begins from "In most situations" for re-roofing, then gives a lighter case for small repairs on its roof page, which do not normally need an application.

Part L, the energy rule, applies to a renovated roof on both sides. In England, Approved Document L 2021 sets the roof figures in its tables for existing elements; in Wales, the Welsh edition does the same with its own numbers. A newer edition takes effect in England on 24 March 2027 and in Wales on 4 March 2027.

Stage six: clearing up, and what guides say it costs

The last stage is the one you see afterwards. Foam offcuts and any rubble are bagged and carried out, the loft is swept, sheeting is lifted and the site is left tidy. The waste leaves with us.

Costs depend on the job, so figures here come from published guides, not from us, and each is a typical UK range rather than a quote. MyJobQuote gives £40 per m² as the average cost of spray foam removal, and around £3,200 for a three-bed detached house. Checkatrade's July 2026 guide quotes £50 to £75 per m² for open-cell removal and around £80 to £100 per m² for closed-cell, and lands on around £3,200 for its own three-bedroom detached example. Those per-m² figures describe different jobs, so neither gives a sum you can apply to your own roof.

What sets the price on a given house:

  • which foam it is, since closed-cell is the harder to lift
  • the area covered and how thickly it was sprayed
  • whether the foam is stuck to felt, a membrane or the tile backs
  • how much timber, underlay and covering needs replacing once it is open
  • the access, including whether scaffold is needed

When two firms quote, look for a line on VAT and on scaffold in each, or the two totals will not be a fair pair.

The survey ends with a single written total, and a separate answer on spray foam removal cost goes further on the numbers. If you are selling or remortgaging, note that in March 2023 RICS reported concern spreading in parts of the mortgage market, with equity release named as one example, so ask your own lender early, before a buyer or a remortgage forces the issue.

Taking foam out: questions and answers

Can foam be taken off from inside the loft alone?

Much of the work happens from the loft side, with rafters, battens and underlay reached from below. Where the foam is bonded to tile backs, a few tiles may need lifting from outside to free it. The survey decides which, and the scaffold stays within the price you are given.

Will I see what is found under the foam?

Yes. Each rafter bay is photographed as it is cleared, and timber that is sound, damp or soft is recorded in groups. You receive the full set. If the timber is worse than the survey could show, we stop and agree any change with you in writing first.

Does removal always include new insulation?

The roof needs insulating again once the foam is gone, so the job is planned with that in mind. What goes back depends on how the roof is made and on the Part L figures for your side of the border, which differ between the two nations.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing