A roof survey is mostly looking. We look at the covering, the ridge and verges, the valleys and flashings, the gutters, and then at the roof from the loft. On a conventional roof the loft view gives the most information, because the rafters, battens, underlay and wall plate are all in sight. Water marks, rot, rusted nails and daylight tell the story.
Spray foam takes most of that view away. The foam is bonded to the surface it covers, and what lies behind it stays out of sight until the foam is cut back. So a survey of a foam-lined roof is a different exercise: part inspection, part inference, and part clear list of what could not be reached.
This guide takes those three parts in order. It covers the outside, the loft, the measurements that can be taken, the points where a survey runs out, what third-party sources say surveys cost, and the England and Wales rules that follow if the foam comes out. It belongs with our other work on spray foam removal.
Starting outside, where nothing is hidden
The foam sits inside, but the covering outside is fully visible, and it tells you a good deal. We begin at the skyline, with the ridge line, the edges of the gables, the chimney and its flashings, and the internal gutters formed where two slopes meet. A faulty ridge or flashing lets water into a foam-lined roof as readily as any other, and once the water is behind the foam it has no obvious way out.
From there we work down the slopes, looking for tiles or slates that have slipped, cracked or gone, then check the eaves, the gutters and the downpipes. Photographs are taken at each stage, so you see for yourself what the roof looks like from above. We note the gutters and downpipes too, because water that overflows at the eaves can soak a wall plate and give a damp reading inside unrelated to the foam.
This outside survey matters for a second reason. If the covering is sound, damp found inside is more likely to be moisture from the house than water from the weather, which changes the diagnosis. Our guide to spray foam and condensation follows that thread.
The outside survey also shows how the covering is held on. On older roofs the nails and the mortar bedding matter. Marley says that since the 2015 amendments, mortar "could no longer be relied upon as the only means of securing the roof covering", which is worth knowing when a ridge or verge is being assessed. Loose or crumbling bedding on a ridge also gives a way for water to get behind the foam, and it is the sort of defect that a survey from the ground alone can miss.
In the loft: what the foam surface shows
Inside, the foam surface is the evidence. We photograph it from several points and note where it starts and stops, because foam that halts short of the eaves or the wall plate leaves a different situation from foam that runs all the way down.
| What we see | What it can suggest |
|---|---|
| Soft, sponge-like foam | Open-cell, the more vapour permeable type |
| Hard, dense foam | Closed-cell, which does not pass vapour |
| Cracks or gaps at edges | Movement, or foam that has shrunk or lifted |
| Staining at the eaves | Moisture reaching timber that is still visible |
| Foam over the underlay | A sheet that may be bonded to the foam |
The first two rows rest on the Energy Saving Trust's description of the two types. A surveyor identifies the type by touch and sight, which is a good indicator but not a laboratory result, so the written summary words it as likely rather than certain.
Some roofs carry foam over only part of the void, for example above a loft conversion. In that case the survey also records the boundary between foamed and unfoamed roof, since that is where condensation and timber problems can most easily develop. Where the foam meets a chimney breast or a party wall, we look for gaps in the seal. Light showing through a gap means air can pass, and air that passes carries moisture with it. We also note whether the loft hatch was sealed with foam, since a hatch that has been sprayed shut is hard to open and harder to inspect.
Measuring what can be measured
A survey that stops at looking misses the timbers, so we add readings. A moisture meter gives a number for the damp in a piece of timber, and a thermal camera can show cold or warm patches, but both have limits on a foam-lined roof. They read the surface or a short distance below it. They do not report on a rafter buried in dense foam.
Where the readings are most useful is at the edges of the foam. These are the exposed ends of rafters, the wall plate, any timber around a chimney breast, and the timbers in the gable. Marks or high readings there are evidence of what could be happening further up, and they help decide whether the foam can stay.
The roof also has a build-up under the covering, and part of that is the underlay. Marley notes that a roof under HR underlay, the high-resistance kind, needs the eaves openings it specifies: 25mm for pitches of 15 degrees or less, and 10mm above that. Whether that opening survives under foam is something we check at the eaves, where the foam meets the wall.
Everything is recorded with photographs and short notes, and you receive a written summary of each reading and where it was taken, so a later survey can repeat the same points and show whether anything has changed. A single set of readings is a snapshot. Readings taken in winter and again in summer say more about a roof than one visit can, and a second visit is suggested only where it would add real information.
What cannot be seen without lifting the foam
There is a hard limit, and it is better stated than hidden. Without removing foam, nobody can see the faces of rafters and battens behind it, the condition of the underlay, the state of the nail fixings, or the back of the covering. A survey can narrow the questions, but it cannot answer them from the surface.
If a doubt is serious enough, there is a middle step. We can cut a small window in the foam, in a spot that is simple to make good such as near the eaves, and look at the timber and underlay behind it. You decide whether that happens. The window gives a direct sample from one point and tells you whether the foam is stuck hard to the timber, whether it has pulled away, and what the wood looks like. One window is not the whole roof, and the written summary says so. The foam is made good afterwards, and the opening is photographed before and after so you have a record of what was done.
The alternative is full removal, which shows everything. Our guide to how spray foam is removed sets out the stages, and the guide on what spray foam does to roof timbers explains what we look for once the timber is exposed.
No survey can promise what is behind the foam. What it can do is give you the evidence to decide between keeping the foam, watching it and taking it out.
What a survey costs and what follows it
These are third-party figures for roof surveys in general, not our prices. MyJobQuote, on a page dated 12 October 2026, puts a typical roof survey at around £300, and its table breaks that into three kinds:
- a basic visual roof inspection at £100 to £200
- a full roof survey at £250 to £400
- a drone roof survey at £200 to £350
A survey of a foam-lined roof may need the fuller kind, because of the loft work and the written summary. The survey leads to one written total price for any work we recommend. For removal itself, MyJobQuote (17 September 2026) gives £40 per m² and around £3,200 for a 3-bed detached property. That describes a typical house, not yours, so read it as a guide to scale, because the roof area, the foam type and the access decide the real sum.
Whatever written quote you are shown, from us or anyone else, check whether VAT and scaffold are included before comparing totals. A quote that leaves either out is not a total, however low the headline figure looks. Where the job needs scaffold, it sits inside our written quote, and the survey tells you whether it does, since the eaves height and the access to the roof settle that. Ask for the quote to say plainly what the scaffold covers and for how long it stays up, so the total you compare is a true total.
Rules that apply if the foam comes out
Taking foam off a roof and putting insulation back can bring Building Regulations into play, and each country takes its own view of the same work. The list below gives each country's rule in its own words.
- In England, AD L 2021 Table 4.3 sets 0.16 for a renovated roof, with a threshold of 0.35 and a relaxation in paragraph 4.13. AD L 2026 takes effect on 24 March 2027.
- In Wales, Table 11.1 of the Welsh AD L sets 0.16, and not worse than 0.35 where 0.16 is not feasible. A new edition takes effect on 4 March 2027.
- In England, the Planning Portal's re-covering test needs less than 25 per cent of the building envelope and less than 50 per cent of the roof to be touched before an application is normally unnecessary.
- In Wales, the Welsh Government's guidance on re-roofing starts from approval being needed in most situations.
The Welsh text adds that the whole element should be improved where the renovated area is greater than 50% of it. Those thresholds decide whether a roof stays as a repair or becomes a renovation in the eyes of building control.
Before any work starts we check with the council's building control team, or a registered building control approver, which of these applies to your roof. The inspection findings from the survey go with that enquiry, so the building control officer sees the same photographs you do. If the answer is that approval is needed, you hear that before you commit, and the written total price covers the work as it will be done.
