01432 610152 Get a quote Call 01432 610152

Slate sizes

Do slate sizes matter for a repair?

Yes. A replacement slate has to match its neighbours in length, width, thickness and source, or the overlap and the line of the course are lost.

In brief

Yes. A slate's length decides how much of it the courses above cover, and Cupa's pitch guidance is built on a 500 mm slate with a 115 mm overlap. Thickness decides whether the slate lies flat against its neighbours or lifts an edge into the wind. Colour and source decide whether the patch shows from the lane. So a repair slate is matched on all of these, and we measure before we order.

How length, overlap and the battens fit together

Slates are hung in rows called courses, each row fixed to a batten, which is the timber lath running level across the rafters. Every slate has its upper end covered by the course above. That covered distance is the overlap, and it stops rain being pushed up or through the joints in a gale.

Cupa, the slate producer, ties its minimum pitch for natural slate to figures. Its 20 degrees assumes moderate exposure, a slate 500 mm long and an overlap of 115 mm. Change the length or the overlap and the sentence no longer describes the roof. That is the first reason sizes matter. A slate that is shorter than its neighbours leaves less cover at the joint, and one that is longer changes the spacing the battens were set to.

Roofs are set out for the slates they carry. The battens were nailed at a spacing worked out from the original slate length, so a replacement of another length does not fall naturally into place. It either sits short, with the lap reduced, or it pushes the course above out of line.

Thickness, colour and source

Length is only the start. A repair slate is checked against the old ones on four counts:

The four points a repair slate must match
PointWhat goes wrong if it differs
LengthThe overlap and batten spacing are upset
WidthJoints between slates no longer break across the course below
ThicknessAn edge lifts and gives the wind a hold
Colour and sourceThe patch shows as a different shade

Source matters because slates from different quarries age differently. SPAB explains that Welsh slate now implies slate from the north-western corner of Wales, along the Nantlle to Bethesda slate belt, with workings that continue at Bethesda and at Blaenau Ffestiniog. A Spanish slate or a reclaimed Welsh slate looks different and has its own typical life. HomeBuilding gives Welsh slate at 100 or more years, Spanish at 75 to 100 years and reclaimed Welsh at 50 to 80 years, as approximate ranges and not promises.

Our page on reclaimed Welsh slate covers what to check when old slates are reused.

What we do when no slate matches

Sometimes a matching slate cannot be bought. Production changes, a quarry closes, or a roof was laid with a size nobody cuts now. There are three honest routes, and we take the one that suits the roof.

  • Borrow from a hidden slope. Sound slates from a rear or inner face go to the front, and the less visible face takes the new ones.
  • Buy reclaimed slates that match by size, thickness and shade, and check each one for cracks before it goes up.
  • Re-slate the slope, if the patch would be so mixed that the repair looks worse than the fault.

Price pulls in different directions. HomeBuilding gives supply-only Welsh slate at £185 per m² against £72 per m² for Spanish, so a patch in a cheaper slate costs less to buy. It will not match a Welsh roof, and the saving is small beside the cost of the access. Checkatrade's June 2026 repair rates (excluding VAT) put natural slate at £150 to £220 per m², on patches up to 3 m². These are third-party figures and are never multiplied into totals. Our own number comes in the written quote as a single total, and the quote names the slate we have matched, with the measurements behind that choice.

How we measure before we order

The survey starts with the slates that have already come off, if any are lying in the gutter or the garden. We measure those, and then, where a sound slate can be lifted without harm, one from the roof as well.

  1. Measure the length, the width and the thickness of a sound slate from the same slope.
  2. Photograph it on a rule, beside a fresh slate if one is on site.
  3. Check the batten spacing wherever a slipped slate shows it.
  4. Record the colour of the slate in daylight, and note any weathering.

The measurements go in with the quote. A full slope brings approvals into play, and the two countries treat it differently. England: the Planning Portal's re-roofing test looks at the building envelope and the roof, with thresholds of less than 25 per cent and less than 50 per cent. Wales: the Welsh Government expects Building Regulations approval in most situations, as our page on re-slating in Wales explains. For a closer look at the lap, see slate pitch and headlap, under slate roofing.

Related questions

Can I use a slightly thicker slate if the length is right?

It is a poor swap. A thicker slate sits proud of its neighbours, and the exposed edge gives the wind something to catch. We match on thickness as well as length, and where only a thicker one is available we look again at reclaimed stock or a different slope.

Does a cheaper Spanish slate work in a Welsh slate roof?

It will keep the rain out, but it differs in shade and in typical life, with HomeBuilding giving Spanish slate 75 to 100 years against 100 or more for Welsh. On a front slope the difference shows from the road. We match the source wherever we can, and we explain the trade when we cannot.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing