The roof is the part of a house people see least and think about last. A yearly check takes an hour or two, needs no ladder, and gives you a dated record of how the roof looked, which is worth having if a fault appears later or an insurer asks. The method is the one a roofer follows: begin at the skyline, where the roof meets the sky, and work downward.
That order has a reason. The skyline features carry the most joins, and a join is where a covering can part. After them come the slopes, the eaves with their gutters, the flat roofs and finally the loft, where problems outside show up as marks within. You can do the first and the last parts yourself from safe places. Anything that needs a ladder, a tower or a foot on the covering belongs to a roofer.
The sections below take the check part by part, with the standards and published figures that bear on each, and they say what changes between England and Wales when a small repair grows. For the full service, see our roof inspections and surveys page.
Start on the ground with a pair of binoculars
Pick a dry, bright day and walk right round the house, looking up from a distance on each side. Binoculars bring a ridge, a chimney and a valley close enough to read without going near an edge. Take a photograph of each elevation from the same spot every year, so that next year's picture can be set beside this one.
From the ground, these are the things worth a note:
- a ridge line that runs straight, with no tiles lifted or dropped out of line
- tiles or slates that have slipped, or gaps where one has gone
- lead at the chimney and the walls, lifting or showing daylight at its edge
- mortar or fragments in the gutters, or on paths below the roof
- stains running down the wall, which suggest overflowing gutters or a leak
- moss or plants growing in the gutter, at the valley or on the chimney
Stay on the ground for all of this. A ladder against the gutter, a foot on a flat roof or a step onto the slope are the places where a check goes wrong. If a fault needs a closer look, write down where it is, take a photograph with the zoom, and ask a roofer to inspect it from the roof.
Keep the photographs together in one folder, with the date. They are the baseline for the whole check, and they cost nothing. Our guide to what a loft inspection shows covers the same exercise from the hatch.
The ridge, the verges and the mortar that holds them
Ridge and verge tiles take the strongest wind and the most sun, and many are bedded in mortar. Marley says installing to BS 5534 isn't required by law, and it points out that mortar on its own has not counted as enough to hold the covering on since the 2015 amendments. Mortar is not banned. The point is that bedding alone is not the whole answer, and a ridge that depends on old mortar deserves a closer look than one that is also mechanically fixed. BS 8612 covers dry-fix systems.
From the ground, the signs to note are cracks in the bedding, dark gaps between the ridge tile and the tile below, and fragments of mortar in the gutter beneath. On a gable end, a verge that has begun to pull away from the wall shows as a ragged line.
Published repair figures give a sense of scale. Which? (November 2025 survey, ex VAT) gives £80 to £300 to put in one new ridge tile, while MyJobQuote gives an average of £225 to £550 for ridge tile replacement. Checkatrade (June 2026, ex VAT) lists ridge and lead flashing repairs at £50 to £70 per metre. They are different measures and should not be set side by side, and none of them amounts to a quote for your roof.
On a Herefordshire stone-tiled or black-and-white house, the ridge may be a different construction altogether, so the roofer matches the repair to the way that roof was built. Our guide to inspecting a chimney from roof level covers the next stop on the check.
Chimneys, flashings and lead
A chimney is both a structure and a junction. The stack stands in the roof, and the lead around its foot has to seal the join. Flashing is the lead strip lapped over stack and covering. Soakers, the small folded pieces worked in beneath the tile courses beside a stack, do the same job at the side. Royston Lead's cast-lead table runs from Code 3 to Code 8. Code 3 is "Recommended for lead soakers only", while Code 4 is listed for flashings and valley gutters as well as soakers, with dormers on its list too.
The atlas of Herefordshire building stone calls the large outside stacks of the black-and-white villages "commonly of local sandstone", so the pointing of a stone stack is as much a part of the check as the lead. Look at the stack from the ground for any lean, any open joints and any dark staining below.
On lifespan, MyJobQuote's line is that flashing "can last for over 80 years" when correctly installed, which makes it a hedge and not a pledge. Its published repair figures are around £200 for a patch repair on a chimney flashing, around £570 for a full replacement, and £350 to £920 for full leadwork, which it ties largely to whether scaffolding is needed.
If a flashing has lifted or the pointing has gone, take a photograph and ask a roofer. A small repair now costs less than the damage from a lifted flashing left through a winter, and the photograph shows the roofer exactly where to look first.
Slopes, valleys, eaves and gutters
On a tiled roof, the faults to find are slipped, cracked or missing tiles. On slate, they are slates shifted out of their courses or cracked across. Where a Herefordshire house has a stone roof, the covering is traditionally local sandstone tilestones, and SPAB's phrase for Welsh slate and stone roofs is "predominantly double-lapped", so one displaced piece can expose the layer beneath. At a valley, where two slopes meet, a channel lined with lead, GRP or tiles carries the water down, and any moss or debris in it should be cleared before it dams the flow.
Gutters need a fall to move water along. Brett Martin gives "1mm for every 600mm". A gutter that holds water along its length, or overflows at one point, can send water onto the wall and may be mistaken for a leak from inside. Which? (November 2025 survey, ex VAT) gives £75 to £350 for clearing the guttering at both front and back.
| Covering | As published | Source |
|---|---|---|
| Concrete tile | Around 60 years, or 40 to 50 years | Marley, HomeBuilding |
| Clay tile | A minimum of 60 years, clay only | BRE via Marley |
| Welsh slate | 100+ years | HomeBuilding |
Treat these as typical ranges and not a countdown. They are no reason to wait for a covering to fail, and a roof that has reached the middle of its range is the one where a yearly look matters most.
Flat roofs, the loft and the signs of condensation
Flat roofs over extensions, garages and porches need their own look, from an upstairs window or from the ground. Ponding that has not drained by the next day, blisters, splits in the membrane and a gap at the upstand where it meets the wall are all worth a photograph. NFRC says BS 6229:2025 sets "a minimum 1:80 finished fall for general roof areas and internal gutters", and IKO advises designing for 1:40 to achieve it. BS 6229:2025 is the standard for membrane flat roofs, and it excludes lead.
Lifespans differ between sources. HomeBuilding gives EPDM 25 to 30 years where Less gives 30 to 50, GRP 25 to 30 years where Less gives 25 to 40, and felt 10 to 15 years where Less gives 10 to 20. Our guide to inspecting a flat roof goes into membranes, falls and edges.
In the loft, use a torch with boards or joists underfoot. Look for dark rings on timbers, damp insulation, daylight through the covering, and frost or condensation on the underside in cold weather. Marley explains that an HR underlay, short for high resistance, passes no vapour and so relies on eaves ventilation: 25mm along the eaves for pitches of 15° or less, and 10mm above that pitch.
If the loft holds bats, leave them alone. Section 9(4) of the Wildlife and Countryside Act 1981 applies where a bat's roost is disturbed, intentionally or recklessly, by anyone, in England and in Wales alike. Bat licences come from Natural England for English addresses and Natural Resources Wales for Welsh ones.
After a storm, and keeping the paperwork
A storm check is a short version of the annual one, made once the weather has passed. The Financial Ombudsman Service says that "a storm usually involves violent winds, usually with rain, hail or snow", and that "Rain, hail or snowfall by itself can constitute a storm". Whether the policy responds is for you and your insurer to sort out. Alongside expert reports, the Ombudsman says, it usually looks at photos of the property's condition, so your yearly photographs of each elevation are exactly the kind of record that helps.
The plain steps after damage are general advice:
- Make the roof safe from inside and stay off it.
- Take photographs of everything as you find it, before any clearing up.
- Contact your insurer before you book any lasting repair.
- Keep photographs and receipts for any temporary work.
MyJobQuote (22 October 2026) gives emergency roofer call-out costs of £150 to £300, with extensive storm damage repairs reaching £1,200 or more. For a roof survey it gives around £300, with a basic visual inspection at £100 to £200.
If a repair becomes a re-cover, the side of the border decides the rule. In England, the Planning Portal's test for a heavier covering is "by 15 per cent or more", and that needs approval. In Wales, the Welsh Government says re-roofing in most situations will need Building Regulations approval. We confirm with the right building control body before work starts, and once the survey is complete, a single written price covers any repair.
