01432 610152 Get a quote Call 01432 610152

Inside the roof space

What a loft inspection shows about the roof above

From the loft hatch you look at the roof from beneath. Timber, underlay and insulation keep a record of every leak and draught, and a torch and a camera are enough to read it.

Horizon Roofing Hereford 9 min read

The garden is where a roof can get judged: a slipped tile here, some moss there. The loft gives the other half of the picture. From inside, you see the back of the covering, the timbers that carry it and the layer under the tiles that catches whatever gets past them. A roof that looks tidy from the road can show a good deal of history from the hatch, and a roof that looks tired outside can turn out to be dry and sound within.

A loft inspection is that second look, done in daylight with a strong torch and a camera. We walk the joists, or the boarding where there is any, and never the ceiling between them. Each mark is photographed and placed against the part of the roof it sits under, so it can be matched with the outside check.

This guide runs through what the loft shows, in the order we read it: the timbers, the underlay, daylight and damp, ventilation and insulation, and the things to leave alone. It marks where England and Wales differ. For the wider range of checks, see our roof inspections page.

Why the loft tells you what the garden cannot

A roof covering is only the visible layer. Under it sit battens, the thin timber strips that tiles or slates hang from, and rafters, the sloping timbers that carry them. Between the two there can be an underlay, a sheet or old felt that catches stray water and sends it down to the gutter. From outside, you see tiles. From inside, you see what the tiles have been doing to the structure.

That is why the loft is the quickest place to learn whether a roof is leaking, how long it has been leaking and roughly where. A drop of water leaves a mark on timber that stays after the roof dries. Rings, dark patches and rust on nails are a record kept in wood and metal.

The loft also shows what the roof is made of, which matters for the repair. Some older houses were never given an underlay, which leaves the underside of the covering in plain view. Others have modern sheet over old battens, or a patched mix of both. A repair that suits one kind of build can be wrong for another.

We always pair the two views. A mark in the loft is traced to the outside position above it, and a fault on the roof is checked against the timbers below. Our guide to how old your roof is shows how the timbers and fixings help to date a covering.

Rafters, battens and the wall plate

Timber is the first thing we read, because it shows damage that the covering hides. We run the torch along each rafter and batten, checking for the following:

  • dark rings or tide lines, where wet timber dried out and left an edge
  • soft or crumbling wood, which a thin blade will sink into
  • rust on nails and metal straps, which shows damp has been present for some time
  • sagging between supports, or a rafter that has twisted or split
  • old repairs, such as extra timbers bolted alongside a weak one

The wall plate runs the length of the wall head and takes the foot of every rafter. It sits just above the eaves, so it is where a failing gutter or rotted underlay lets water in first. Damp here can travel into the wall below, and a dark, soft plate is a finding in its own right.

Around a chimney breast, we look at the timber trimmed back from the stack and at the base of the chimney inside the loft. Staining around it points to flashings, soakers or pointing on the roof above.

An older timber-framed house can hold its own history in the loft, with repairs made at different times and new timber working beside old. We note anything that looks like a past fault, even where it is dry now, so the owner knows what the timber has been through and which areas deserve a second look at the next visit.

Underlay, daylight and damp patches

Underlay is the loft's main clue. Modern sheet underlay is visible between the rafters, and we check it for tears, sagging pockets and stains. Old bitumen felt can go brittle, split along the rafters and hang in folds. A torn sheet is a route for water, even where the tiles above are whole, and a mark on it that lines up with a tear is a finding we mark on the roof plan and then look for from outside.

Daylight is the quickest signal of all. Switch off the torch and let the eyes adjust: any pinpoint of light through the covering is a gap that water can use. Light at the ridge, along a verge or around a chimney tells us which skyline joint to open first, and a few pinholes in old lime torching between the battens, where it exists, tell us the joint is drying out.

Wet marks are read together with their position.

What a mark in the loft can point to
What we seeWhat it suggests
Ring below the ridgeRidge bedding or capping gaps
Stain beside a chimneyFlashing, soaker or pointing failure
Wet batten under one tileA cracked or slipped covering above
Damp across the whole roof spaceCondensation more than a leak

The last row matters. A uniform dampness, with water droplets on the underside of the covering and nothing leaking from any one place, calls for a look at ventilation. Our guide to what causes condensation in a loft goes into that in more depth.

Ventilation and why it matters up there

A roof space needs air moving through it, so that warm, damp air rising from the house does not settle on cold timber and turn to water. How much ventilation is needed depends on the build of the roof, and the underlay is the deciding factor.

Marley supplies the figures. For a cold roof under HR (high resistance) underlay, its guidance sets an eaves gap of 25mm for pitches of 15° or less, and 10mm for steeper pitches. Because that sheet lets no vapour through, the gap does the work. Where an air-permeable underlay (called LR) sits over a well-sealed ceiling, Marley treats the normal gaps in eaves construction, around 3mm, as enough, provided the product's UKAS certification conditions are met.

In the loft we check three things:

  • whether eaves vents, where fitted, are open and not stuffed with insulation
  • whether ridge or tile vents exist, and whether anything blocks them
  • whether the ceiling below is well sealed, with no hatch gap or open light fitting letting damp air up

Insulation pushed hard into the eaves is a common cause of blocked ventilation, and a mark on the timber just above it shows the damp it holds. The standard is BS 5250, which Marley cites, and it is currently under review.

A well-ventilated loft smells dry. A musty smell, white or black mould on timber and beads of water on nail tips all point to air that is not moving, and we photograph each one against its position under the roof.

Insulation, and spray foam in particular

What lies on the loft floor, or under the rafters, affects both the roof and the house. We look at depth, gaps and whether the insulation is wet or compressed. Flattened, damp insulation under a drip tells us the position of a leak, and its dryness elsewhere suggests the fault is local.

Spray foam needs separate mention. It is applied to the underside of the roof, so it covers exactly the timbers and underlay we would otherwise read. The Energy Saving Trust separates closed-cell foam, which it says is not vapour permeable, from open-cell foam, which lets more vapour through. Both types sit hard against the rafters and slow their drying, though in the Trust's words open-cell foam brings a rot risk that "should be much lower". That difference is worth knowing before anyone decides whether foam can stay.

Foam hides evidence, so a loft inspection under foam can only record what is visible: the foam itself, its condition and any signs at the edges. On the lending side, RICS reported in March 2023 that some corners of the market, equity release mortgages among them, had raised concern, so ask your lender. Its consumer guide also asks owners to find out from the mortgage provider whether lender policy allows foam at all.

If foam is on the roof and you want it looked at, we photograph its state and edges, and explain what can and cannot be judged without taking some of it away.

Safety, wildlife and what to leave alone

A loft is not a room. Boards are partial, light is poor and the ceiling is only plasterboard. If you look yourself, take a torch, keep to the joists or boards, and stay clear of wiring and anything that sags. Look and photograph rather than touch, and never put a foot between joists. Open the hatch fully before you climb, wear a mask and gloves, and use a head torch so both hands stay free for the ladder.

Leave these alone:

  • lagged pipes or tanks, which can hold hot or stored water
  • old wiring, especially cloth-covered cable, and any junction box
  • boxes of loose insulation of unknown age
  • any sheet that might be asbestos cement

Lofts also hold wildlife. Roof work can disturb bats, and GOV.UK lists "repairing or replacing a roof" as one such activity. Natural England issues bat licences for English addresses, and Natural Resources Wales for Welsh ones. A live nest needs the same care. If droppings, a roost or a nest in use turn up, work halts at that spot and the owner hears what comes next. Our guide to bats found during an inspection explains the steps.

On price, a basic visual inspection is £100 to £200 in MyJobQuote's table, and a full survey £250 to £400. A loft check forms part of the survey, and any repair it leads to is quoted afterwards as one total.

The loft inspection: your questions

Do I need to clear the loft before the inspection?

Clear the area round the hatch so a person can climb through with a torch and a camera. Stored boxes elsewhere can stay, though a note of what cannot be moved helps. We keep to the joists and boards, and we leave alone anything that looks fragile or unsafe.

Will a loft inspection find a leak on its own?

It can show where water has been, with rings, staining, daylight and wet insulation. It does not always show the cause, because a fault can hide under a lap. That is why we pair the loft with a check from the roof, and trace each mark to the part of the roof above.

Can you tell what is wrong if my loft has spray foam?

Only in part. Foam covers the timbers and underlay we would otherwise read, so we record the foam itself, its edges and any signs of damp around it. If more is needed, we explain what could be learned by taking some away, and whether that is worth doing.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing