A drone roof survey is a set of photographs and video taken by a small camera aircraft that flies over and around the house. For a tall or steep roof, a roof with a fragile section, or a long run of slates that is hard to see from the garden, that view is worth having. The whole roof comes back in a handful of frames, and the images can be enlarged, saved and set beside a later flight.
What the camera records is the outer face of the covering, in the light of that day. It does not record whether a tile moves under a hand, what the loft looks like, or whether the timbers beneath are sound. Those questions need someone to touch the roof, or to climb into the roof space with a torch.
This guide sets out what a drone view does well, where it falls short, what it costs and how the images turn into a decision. It also covers the England and Wales rules that start to matter once a survey leads to re-covering. For the wider picture, see our roof inspections page.
What the view from above shows well
Height is the whole advantage. From the ground, a ridge line is a thin strip against the sky and a valley is out of sight. From the air, you can follow the ridge tile by tile, look straight down a valley, and see the top of a chimney stack, the one spot a ladder may not reach safely.
On a roof you would rather not walk on, a flight also removes a risk. It also saves disturbing the covering: every footstep on old slate or tilestone is a chance of a crack. Old stone tilestones, brittle fibre cement sheets and a rotten flat roof deck can all give way under a person, and a camera weighs almost nothing. Roofs of local sandstone tilestone, drawn from the St Maughans sandstones around the Golden Valley according to the county's stone atlas, are heavy, uneven and easily cracked underfoot, so a clear overhead picture is welcome before anyone goes near.
Good aerial images pick out:
- ridge or hip tiles that have shifted, cracked or lost their bedding
- slipped, missing or broken slates and tiles across the open slopes
- the mortar line along a verge, the sloping edge at a gable
- lead flashings around a chimney that have lifted or split
- moss or algae that has built up on one slope and not another
- ponding on a flat roof, where water stands after rain, and the dark tide line it leaves
- gutters that sag, overflow or hold a crop of seedlings
- valleys blocked with leaves and moss
The images are also a record. A set taken before a repair and a set taken after it show what was done. That suits our way of working, because the photographs of your roof are yours to keep and compare.
What a camera cannot judge
An image shows the surface, so any fault that is not on the surface stays hidden. A tile can sit perfectly flat and still hang by one rusted nail, or have a broken nib, the lug on its back that hooks over the batten. The picture looks fine. A hand finds the problem in a second, and a pole camera pushed under the lap shows it better still.
Underlay, battens, rafters and insulation are all out of frame. So is the wall plate, the beam on top of the wall on which the rafters rest. Stains on the ceiling, damp insulation and daylight through the covering belong to a loft inspection, which our guide to what a loft inspection shows describes.
| What you are checking | Drone photographs | Needs a closer look |
|---|---|---|
| A slipped or missing slate | Can show | Confirm from the roof |
| Loose ridge bedding | Cracks may show | Hand test along the ridge |
| Rotten battens or rafters | Not visible | Loft inspection |
| Condensation in the roof space | Not visible | Loft inspection |
| Fixings behind tiles and slates | Not visible | Lift and check |
Asbestos is a separate point. Old sheet roofing, on a garage or an outbuilding, may be asbestos cement, and HSE's guidance treats those roofs as fragile at all times, so nobody should climb onto one for a closer view. A photograph cannot tell you what a sheet is made of, since only a sample can settle that, but it lets you study a suspect roof without stepping onto it. The same goes for rooflights set in a corrugated sheet roof, where a plastic panel can sit hidden under moss with brittle sheets all around it. Pitch is another gap: a camera looking down gives a poor sense of how steep a slope is, and the pitch decides which coverings are suitable and how they must be fixed.
Light, weather and what a flight can capture
A drone survey depends on the day. Flat grey light suits a camera, because it shows texture without hard shadows. Low winter sun does the opposite: a long shadow behind every ridge tile can hide the very crack you are after. Rain on the lens and a wet, shining surface make slate and glazed tile look uniform, so a flight is best put off for a dry day with steady light.
Wind limits a flight too. The angle matters as well. Straight-down images show the layout of the roof, while oblique images, taken from the side, show the faces of the tiles and the state of the joints.
Photographs also flatten depth. A dip in a slope, caused by a sagging rafter or a failed purlin, can be hard to read from one overhead frame. A good survey shoots the same slope from more than one angle, and where something looks wrong, the next step is a check by hand. Shade from a chimney or a tree can hide a fault on one slope.
Four more points are worth asking about before you book:
- whether the images are handed over, or only a summary of them
- whether the flight covers the back of the house as well as the front
- how sharp the images are when enlarged to a single tile
- who studies the images afterwards, and whether that person goes up on the roof if something is unclear
On registration, MyJobQuote's roof survey page states that flying a camera drone of 100g or more needs an Operator ID as well as a Flyer ID, both issued by the Civil Aviation Authority (CAA). That is MyJobQuote's statement, so confirm it with the Civil Aviation Authority yourself, and ask any supplier to show you their IDs before the flight.Our guide to registration for drone survey flights looks at it more closely.
What a drone survey costs
Surveys are priced by type of inspection, and the drone version sits between the basic and full ones. MyJobQuote's roof survey page, last updated 12/10/26, puts the average roof survey at around £300, with these ranges:
| Type of survey | Price range |
|---|---|
| Basic visual roof inspection | £100 to £200 |
| Drone roof survey | £200 to £350 |
| Full roof survey | £250 to £400 |
These are third-party UK ranges for each type of survey. They are not a price for your house and not a Horizon price. On a real house, the cost moves with the height of the building, the number of separate roof sections, how much of the roof can be reached and what the report has to cover.
A flight can also save a step. Without one, a high roof may need access equipment before anyone can even look at it. With one, a fault that shows in the pictures can be identified first, and only then does a decision about access follow. Whether that holds for your roof depends on what the images show, and on how many hours of work the supplier puts into reading them afterwards. A low garage or single-storey extension may be easier to inspect from a ladder than from the air, so the choice of tool is worth settling before anyone books.
If the pictures lead to a repair, the figure you are given is a single total on paper, produced after a survey of the roof itself. Our separate guide to drone roof survey cost goes through what to ask a supplier before you agree to anything.
When the images lead to work: which rules apply
A survey that finds a failing slope leads to a repair or a new covering, and from there the border matters. England and Wales set different tests, and a Welsh address follows the Welsh ones only.
- In England, the Planning Portal says no Building Regulations application is normally needed where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" is affected.
- In England, the Planning Portal puts the weight trigger at 15 per cent or more added by a new covering, while AD A, the structural document, says "more than 15%".
- In Wales, the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval."
- In Wales, the same Welsh Government page gives slate swapped for tiles as an example where approval is likely, with the structure, fire performance and energy use all in question.
On a job of that scale, building control gets a call from us first, whichever side of the line the house sits: the council's service, or a registered building control approver.
Flat roofs carry an energy rule as well. Under AD L 2021 in England, a new waterproof covering laid on a flat roof is classed as renovation, and the Welsh AD L treats it the same way in Wales. So images of a flat roof that ponds can end in an insulation upgrade as well as a new membrane, and the written total allows for that before work starts. Part L is the energy section of the Building Regulations.
If the drone shows damage after a storm, take your own photos too. Talk to your insurer before any permanent repair starts, and hold on to every receipt for temporary work.
