Binoculars show the outline of a stack. They do not show a hairline crack in a flaunching, a joint that has opened between brick and lead, or a pot that rocks when a hand is laid on it. For those, someone has to be at roof level, beside the stack, with a camera and a trowel-sized pointing tool for testing the mortar.
A chimney is also the part of a house that takes the harshest weather. It stands proud of the roof, it is wet on every face, and it carries a joint with the covering on all four sides. A fault that begins as a loose collar of mortar at the top can end as a stain on a bedroom wall.
The order runs from the pots to the masonry, then the lead around the base, then the roof next to it. The guide also covers what the findings can lead to and which rules apply on each side of the border when work goes beyond a repair. For the wider range of surveys, see our roof inspections page.
Why a stack needs a close look
From a distance, a stack gives away little. Brickwork weathers evenly, and a dark patch on stone can be damp, lichen or shade. Only at arm's length do cracked joints, loose pots and lifted lead show themselves, and only by hand can you tell sound mortar from mortar that crumbles.
The reasons to look closely are practical. Rain that gets into a stack travels. It runs down the flue lining, into the chimney breast inside the house, and out as a brown stain on the wall or ceiling. A stack that leans, or has shed its upper courses, can also drop pieces onto the roof, the path or the neighbour's garden. Falling masonry is the risk that makes this a safety check as well as a damp check.
It helps to name the parts, because every report you read will use them:
- the pot, the clay or metal outlet at the top of each flue
- the flaunching, the sloped mortar bed that bonds the pots to the stack and sheds rain off the top
- the cap or cowl, if one is fitted over the pot
- the shaft of the stack, in brick, stone or render
- the flashings, the lead strips that seal the joint between stack and roof
- the soakers, small folded pieces of lead that slot under each tile or slate course at the sides
Our guide to whether a roof can be inspected from the ground explains how far a ground-level look can take you before a climb becomes the better option.
From the pot down: what each level can show
The inspection runs from the top down, because rain and loose debris both travel in that direction.
The pots come first. We check that each one is seated, that none has cracked, and that any cap is secure. A pot that has loosened in its bed can topple in a gale, and a cracked pot lets rain straight into the flue. The flaunching beneath is the usual weak point: it cracks as it ages, shrinks away from the pots, and then lets water in around their bases. A small cracked patch is a repair; a collar that is crumbling or hollow when tapped has to be replaced.
The shaft is next. Pointing, the mortar that fills the joints between bricks or stones, is checked for gaps, erosion and any sign of a repair in a mortar harder than the masonry around it. We check for cracks that run through brick as well as joint, and we look for lean by sighting up the stack against the line of the gable. Stone stacks and brick stacks need slightly different judgement, which a later section covers.
| Level | What we check | What a defect can mean |
|---|---|---|
| Pots and cowls | Seating, cracks, loose caps | Rain into the flue; toppling in wind |
| Flaunching | Cracks, hollow sound, gaps at the pot | Water entering at the head of the stack |
| Shaft | Pointing, cracks, lean, spalled faces | Water travelling inside the masonry |
| Lead flashings | Lifted edges, splits, open joints | Leaks at the base, into the loft |
The lead around the base
The joint between a stack and the roof is where we spend the longest. Lead flashings are the strips of sheet metal that bridge it, and they are keyed into the stack's joints on one edge and lie over the roof covering on the other. At the front there is an apron flashing; at the sides, step flashing follows the slope; and behind a stack on the slope above it, a back gutter, a lead channel, sheds water round to either side.
The faults are consistent. Lead that has been pulled out of its chase, the groove cut in the joint, will lift in the wind. Lead that has been stretched by heat and cold develops splits along its folds. Sealant smeared over a gap can mark an earlier repair that has since failed. And a flashing fixed into a joint that has since eroded has nothing left to hold it.
On lifespan, MyJobQuote states that lead flashing, once correctly fitted, can last for over 80 years. It is one source's hedged claim and no promise, and a poorly fixed flashing can fail well before then. A sound flashing should be left alone, and sometimes the finding is that nothing needs doing.
Where a repair is needed, MyJobQuote's page on replacing leadwork on a chimney, last updated 22/09/26, gives these typical UK figures:
- a patch repair on a chimney lead flashing: around £200
- a full replacement: around £570
- full leadwork: £350 to £920, with MyJobQuote adding that the figure turns largely on whether scaffolding is needed
Those are third-party ranges, not Horizon prices. On your own house, the height of the stack and the access to it set the total.
Stone stacks, brick stacks and the roof beside them
The county's building stone atlas, hosted by Herefordshire Council, describes the big external stacks on its timber-framed houses as "commonly of local sandstone", and it counts Eardisland, Pembridge and Weobley among the "Black and White Villages". A sandstone stack is built in courses of irregular size, and the joints between them take on the work of keeping water out. Where those joints have opened, a stack can take in water for years before the inside of the house shows it.
With stone, we look at whether the face of a block has flaked, whether the pointing stands proud or has been cut back, and whether an earlier repair has used a mortar that does not suit the stone. With brick, the same questions apply, and we also look at the faces of the bricks themselves for spalling, where the surface has broken away.
The roof around a stack deserves the same attention:
- slates or tiles within a foot of the stack that have slipped, cracked or been replaced with a mismatched piece
- the valley or gutter lining on the high side, where debris collects
- moss on the slope above the stack, which holds water against the lead
- the condition of the ridge if the stack sits near it
Inside the roof space, a stain on the underlay or battens beside the stack, or rust on a metal strap round the chimney breast, confirms what the outside suggested. Our guide to what a loft inspection shows describes that side of the check.
When a check leads to work, and which rules apply
Most findings are small: repointing, a new flaunching, a lifted flashing refixed. Some are not, and then the rules matter. The answer changes with the side of the border the house stands on, so each is labelled.
- In England, the Planning Portal says: "Building regulations approval will always apply when removing chimney breasts as they are part of the building's structure."
- In England, Class C of the 2015 Order, the permitted development class for roof alterations, does not cover installing, altering or replacing a chimney, so ask the council's planning team before changing a stack.
- In Wales, taking a chimney off a house in a conservation area, a National Park or a National Landscape is not permitted development, so planning permission is needed there.
- In England and in Wales, a chimney breast shared with a neighbour brings in the Party Wall etc. Act 1996.
Under that Act, whoever owns the building serves the notice, giving at least 2 months' warning for work on the shared wall, such as removing part of a breast. A neighbour who objects, or who stays silent for 14 days, brings a surveyor into the matter. Party wall questions go to a party wall surveyor, not building control.
A listed house needs listed building consent as well. In England that rests on section 7 of the Planning (Listed Buildings and Conservation Areas) Act 1990; in Wales, on sections 88 and 89 of the Historic Environment (Wales) Act 2023. Building control, the council's service or a registered building control approver, handles the Building Regulations side.
Bats are the other legal point near a stack. Every bat species is protected, roosts included, so a roost found during a check changes the plan. Natural England issues bat licences in England while Natural Resources Wales issues them in Wales.
What to expect from the written price
After a chimney check, you receive the photographs of what we found, and where work is needed, one written total for it. The total allows for access, so ask any quote you receive whether the scaffold is in it.
Before you compare any two quotes for chimney work, ask how each deals with the following, because the price turns on them:
- how high the stack stands, and how it is reached
- how many flues and pots it carries
- how much of the pointing needs replacing, and whether the stone needs dressing
- whether the flashings are repaired or renewed in lead
- whether any part has to be taken down and rebuilt
The photographs we take at roof level go into the written findings, so you can see the pot, the collar, the joint and the lead as they are today. If you later sell the house, or want to show an insurer how the stack stood before a storm, those same pictures show its condition on the day.
For removal rather than repair, MyJobQuote's page on chimney breast removal, updated 03/11/26, puts the average at around £2,500, with a range of £1,200 to £3,500, and £3,000 to £3,500 for removing the whole stack along with the breast. Again, those are third-party figures.
If the stack is leaning, cracked right through or losing its top courses, repair may not be the answer, and a rebuild above the roofline is the better buy. If it only needs a pointing refresh and a new flaunching, that is what we say, and the photographs show why.
