01432 610152 Get a quote Call 01432 610152

Flat roof checks

Inspecting a flat roof: membrane, falls and edges

A flat roof gives its warnings at the surface: a blister, a pool that stays, a lifted edge. This guide covers what an inspection reads in turn, and the rules that follow a replacement.

Horizon Roofing Hereford 9 min read

Flat roofs are never quite level. Each is a gently sloping surface, covered in a continuous waterproof sheet, and it relies on that slope to send water to an outlet. Most of what goes wrong with one comes down to three things: the sheet itself, the slope under it, and the edges where the sheet ends or turns up a wall.

Inspecting one is a close, slow job, done in dry weather where possible, since a wet surface hides hairline cracks and makes a soft deck harder to judge. The surface can be walked in places, felt for soft spots and recorded close up, and each defect can be matched to its cause. A blister over a damp deck is a different problem from a split over a stretched seam, even if both leave the same brown ring on a ceiling.

The sections below take the membrane first, then the falls, then the edges and outlets. A later section sets out what the findings cost, with third-party figures only, and the England and Wales rules for renewing a roof. For the wider picture, see our roof inspections page.

The membrane and how it ages

The membrane is the waterproof skin. On houses, garages and extensions it can be one of three things: torch-on or built-up felt, EPDM rubber sheet, or GRP, which is glass-reinforced plastic laid as a fibreglass shell. The three age differently, so the first job is to work out which one you have, and a rooftop sample or the paperwork from an earlier job sometimes settles it.

Felt shows its age through cracking, blistering and open laps where one strip overlaps the next. EPDM, a single rubber sheet, tends to fail at its glued seams and at the corners where it is folded. GRP is rigid, and its weakness is cracking where a roof moves, sometimes with a hairline line running across the surface.

Lifespans are published as ranges, with no promise attached, and two sources give different figures:

Flat roof lifespans as published
CoveringHomeBuildingLess
Felt10-15 years10 to 20 years
EPDM25-30 years30 to 50 years
GRP25-30 years25 to 40 years

Treat those figures as a spread of published opinion about roofs in good condition. What an inspection records is the state of your own membrane, and a roof at the low end of its range with sound seams can outlast a younger one that has been walked on or left with blocked outlets. Age is a guide to what to look for, and the surface tells you the rest.

Beyond the sheet, the layers matter. A warm roof has its insulation above the deck and below the membrane, while a cold roof has it between the joists below. The build-up decides where moisture can collect, so the survey records which one you have and whether any ventilation gaps are blocked.

Falls and ponding: where the water goes

Fall is the slope that carries water to an outlet or gutter. On a flat roof it is gentle, so small errors show up as pools. Water that stands after the rain has stopped is called ponding, and it is the most reliable sign that the falls are not working.

The standard that covers this is BS 6229:2025, which applies to membrane flat roofs. NFRC says it sets "a minimum 1:80 finished fall for general roof areas and internal gutters". That figure is the finished slope, after the deck, the insulation and the covering are all in place. IKO advises aiming for a design fall of 1:40 so that 1:80 is reached once the roof is finished. BS 6229:2025 covers membranes only; it does not govern lead.

Ponding matters for several reasons:

  • standing water works at every seam and every small defect in the sheet
  • silt and plant growth collect where the water dries
  • the extra load sits on a deck that may already be soft
  • a pool that keeps coming back points to a deflected deck or to settled insulation, which is more serious than the stain

On the day, we look at where the water has dried and left a tide mark, because the marks show where it sat. On a dry day, a long straight edge or a spirit level laid across the surface shows dips that the eye misses. Photographs from several angles help, and a camera held low across the surface shows a dip better than one looking down.

A short-lived pool beside an outlet is not the same finding as a pond across the middle of a roof. Moss and algae at the low point, and a dark ring where silt has dried, tell the same story after the water has gone. The first can be a blocked outlet. The second is a question about the deck.

Edges, upstands and outlets

Edges can give trouble as well as the open surface. Wherever the membrane stops, turns up a wall or meets a roof light, it needs a detail that is built separately and ages separately.

The upstand is the upturned edge of the membrane where it meets a wall. It is covered by a flashing, such as lead or a bonded strip, which sheds water over the top. We look for a flashing that has lifted, a gap above it, or a membrane that has slipped down the wall. At the outer edge, a trim or drip edge guides water into the gutter; a trim that has bent or come away leaves the edge of the deck exposed.

Outlets and gutters take the water off:

  • outlets and gulleys clear of leaves, silt and moss
  • the gutter fall: Brett Martin gives "1mm for every 600mm"
  • the joints and brackets of the gutter, where water escapes
  • an overflow or spillway, where the design has one
  • penetrations, such as roof lights, pipes and vents, each with its own seal

Where the flat roof joins a pitched roof, or abuts the house, the junction is a place to look hard. A pitched roof drains onto the flat one, so all of that water arrives at the abutment. A failed flashing there can send water into the wall rather than the room below it. Our guide to what a roof survey report covers explains how these findings are written up.

Trees close to the roof add to the work at the edges. Leaves collect against upstands and in outlets, and branches that rub the surface in wind scuff the membrane. A flat roof under a tree is checked more often than one in the open.

From findings to a decision: repair, patch or renew

An inspection ends in a choice. A sound sheet with one split or one failed seam can be repaired. A sheet that is cracking, blistering or open across several areas, or that sits on a deck that has gone soft, needs more than a patch. We say which, and show the photographs that explain why. Where a repair will hold, repair is the advice, since a new roof is the larger spend.

What you pay depends on the covering, the area, how the roof is reached and what the deck is like. These are third-party UK figures, not Horizon prices:

  • Which? (November 2025 survey, ex VAT): a felt covering for a typical single garage, 6m x 3m, "£1,400-£3,500".
  • MyJobQuote: an average flat roof replacement between £1,500 and £6,000 in 2026, with felt at £80 to £120 per m² and rubber roofing around £1,050.
  • Checkatrade (June 2026, ex VAT, per m² up to a maximum of 3m²): EPDM repairs £120 to £170 per m², GRP repairs £130 to £180 per m².

A per-m² rate is for a small repair and cannot be turned into a price for a whole roof. For anything bigger than a patch, the figure you are given is one written total, produced after the survey.

Before any quote is accepted, check what it says about the deck, the insulation and the falls,. A new membrane laid over wet or sagging boards will fail early. And ask whether VAT and scaffold are included, because quotes differ on both.

If a roof has leaked, the leak may have wetted the insulation as well. A damp board or wet insulation will not dry under a new sheet, so the findings should say how that was checked. Our guide to the annual roof check describes how often a flat roof is worth looking at.

Rules when a flat roof is renewed

Laying a new covering can bring the Building Regulations into play. England and Wales use different tests, and an address in Wales follows its own country's.

  • In England, the Planning Portal says no application is normally needed where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" is affected.
  • In Wales, the Welsh Government notes that a few flat roof repairs avoid an application, whereas replacing a roof that has built-in insulation can mean upgrading the thermal element.

Thermal element is the Building Regulations term for a wall, floor or roof, and it leaves out windows, doors and rooflights. Energy rules then apply to the renewed roof.

  • In England, AD L 2021 includes a replacement waterproof layer on a flat roof among renovation jobs, and its Table 4.3 sets a roof threshold of 0.35 and an improved value of 0.16 W/(m²·K).
  • In Wales, paragraph 11.16 of the Welsh AD L lists the same job, and its Table 11.1 gives 0.16, and the figure should not be worse than 0.35 where 0.16 cannot be reached.
  • England moves to AD L 2026 from 24 March 2027, and Wales follows with its new edition from 4 March 2027.

Building control, whether the council's service or a registered building control approver, confirms how these apply to your roof. A heavier covering is a separate trigger: England's Planning Portal puts it at 15 per cent or more, and AD A in England and in Wales says "more than 15%".

A flat roof may also sit against a shared wall, as an extension or a garage does. If work reaches a party wall, the owner serves notice, and the question goes to a party wall surveyor, not building control.

Flat roof inspections: your questions

How do I tell a blister from a bubble caused by trapped damp?

On felt, a blister is a raised patch where air or moisture has been trapped under the surface. A small, dry blister can be left under watch. One that is soft, wet or growing may sit over damp boards and needs opening up. That is a job for a hands-on check, not a photograph.

Is a puddle on my flat roof a problem?

A pool that clears within a short time beside an outlet is minor. Water that is still there after the rain has stopped, or that returns in the same place, is ponding, and it points to the falls or the deck. NFRC gives BS 6229:2025 as setting a minimum 1:80 finished fall.

Can I walk on my flat roof to look?

Only with care, and in some cases not at all. A membrane can be damaged by footwear, and a soft deck can give way beneath you. Photographs from a window, a ladder or a drone, taken without stepping onto the roof, are a safer start, and a roofer can then decide where weight is safe.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing