01432 610152 Get a quote Call 01432 610152

Mastic on lifted lead

Is mastic a fix for lifted lead?

Mastic is a flexible sealant. It can fill a gap for a while, but it does not hold a lifted flashing down.

In brief

Not as a lasting fix. Mastic is a sealant, and a bead of it over a lifted edge hides the gap without dealing with why the edge lifted. The causes are failed wedges, crumbling pointing or a sheet pulled out of its chase. A proper repair refixes the lead and makes the joint good again, and MyJobQuote prices a chimney lead flashing patch at around £200.

What mastic does and does not do

Mastic is a soft, flexible filler that is gunned into a gap and left to skin over. On a roof it can close a hairline joint for some while, and that is all it is asked to do. The usual reason to reach for it is speed, because a tube and a gun are quicker than a repair. It holds nothing. A flashing is held by its fixings, its wedges and the pointing over them, and none of those is replaced by a bead of sealant.

A lifted edge is a symptom. Lead that has come away from a wall has done so because something that was holding it has given way, and mastic laid over the gap leaves that cause exactly where it was. The lead can go on lifting under the sealant, and the sealant, exposed to sun and rain, shrinks and splits in its own time.

The danger of a sealed gap is that it looks mended. Rainwater can still get behind the lead, and a damp mark indoors may be the only warning, long after the bead was put on. We photograph the lifted lead before anything is touched, so that the cause is recorded and the repair goes at the cause itself.

Why lead lifts in the first place

Lead is a soft, heavy metal, and it moves with the temperature. Sheet that is fixed so that it cannot move, or fixed with nothing to hold its top edge, will creep and lift. The causes we look for at the survey are:

  • wedges that have dropped out of the chase, the groove cut into the wall
  • pointing that has cracked, shrunk or fallen out above the lead
  • an edge that has curled where the sheet was cut too long
  • fixings that have worked loose or been pulled through the sheet
  • a split along a fold, where repeated movement has tired the lead

Which of these applies decides the repair. Wedges and pointing are put back. A curled edge is dressed down and refixed. A split is patched, or a section is replaced with new sheet cut to the same detail.

A run of lifted lead on one side of a stack is also worth reading as a pattern. If the same edge has lifted along its whole length, the fault is in the chase or the pointing, and treating each lifted spot separately will not cure it. Our page on why a lead flashing lifts goes through each cause in turn.

What a proper repair involves

A repair that lasts deals with the fixing. In practice that means raking out the loose pointing, refixing the lead into the chase with new wedges, pointing over them and checking that the sheet can move freely at its lower edge. If a section is split or thin, it is replaced.

The code of sheet is chosen from the Royston Lead table. Flashings take Code 4, 5 or 6 (use letter B in that table), and soakers take Code 3 or 4. Code 5 is 2.24 mm thick and weighs 25.40 kg per square metre in that table, so new sheet is a real weight on the wall to be refixed against.

MyJobQuote says a correctly installed lead flashing "can last for over 80 years". The word "can" and the condition about installation matter, because they describe what a fixed-and-pointed flashing is capable of. A bead of mastic makes no such claim.

There is one place where sealant earns a spot: as a short-term stop on a small gap during a wet spell, holding the position until a dry day allows proper work. It is then a bridge to the repair and not the repair itself.

Price and rules: patch against full replacement

MyJobQuote's chimney leadwork page (last updated 22/09/26) puts a lead flashing patch at around £200 and a full replacement at around £570 on average, with full leadwork between £350 and £920, a spread that MyJobQuote links mostly to scaffolding. Those are UK-wide third-party figures. Our price arrives as a single figure after the survey, and where a patch will serve, a patch is what goes in it. A full replacement is quoted when the sheet is split, thin or failing at the chase, and the photographs show which case yours is, so the choice rests on what is visible on the roof.

A flashing repair is a small part of a roof, and in both England and Wales the approval tests count the share of the roof touched. The detail of each test, with the England and Wales wording side by side, is on our page about leadwork in the rain, and a patch to one flashing sits well inside both.

All the lead pages are listed under lead roofing, and our lead flashing repair cost page goes further into price.

Related questions

Can I use mastic as a temporary measure until the repair?

It can plug a small opening for a short period, but it will not hold the lead down, and it can make a gap look sound when it is not. If you do seal a gap, tell us. We photograph the lifted lead first, and we take the sealant out if it is in the way of the permanent repair.

Does sealant on a lead flashing count as a proper repair for my insurer?

Check your policy. The general steps are to inform the insurer before permanent repairs, make the damage safe, and keep dated photographs and receipts. A photograph of the lifted lead before any sealant goes on is worth having, because it shows the state of the flashing before anything covered it.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing