01432 610152 Get a quote Call 01432 610152

Lead flashing lifespan

How long does lead flashing last?

MyJobQuote says flashing that has been fitted correctly can last for over 80 years. That is a statement about good workmanship, not a date.

In brief

MyJobQuote says lead flashing fitted correctly "can last for over 80 years". The words that matter are "correctly" and "can". It is a statement about what a good flashing is capable of, not a promise, a floor or a minimum for any one roof. What decides your flashing is the fixing, the pointing, the code of lead and how the sheet has moved.

What the published figure says and does not say

MyJobQuote's page on leadwork for a chimney, last updated 22/09/26, makes one statement about how long lead flashings can last: that a correctly installed one can last for over 80 years. It is the only lifespan figure sourced for lead flashings.

Read it closely. It starts with a condition, that the flashing is correctly installed, and it uses the verb "can". It gives a length that the best flashings can pass, not a length that every flashing reaches. It is not a floor, so a flashing that fails at 30 years is not contradicting it, and it is not a promise, so no one should read it as a date on a calendar.

It also belongs to flashings alone. The ranges published for a whole lead flat roof are a separate matter with their own sources, and they are set out on our page about how long a lead flat roof lasts. Mixing the two would be a mistake, because a flashing is a narrow strip tucked into a wall, while a flat roof is a whole covering laid over a deck.

Why "correctly installed" carries the weight

A flashing is a thin strip of lead that seals the joint between a roof slope and the wall or chimney beside it. It does its work for decades only if the details around it are right. These are the parts that make up a correct installation:

  • the right code of sheet for the job: Royston lists Codes 4, 5 and 6 for flashings
  • a clean chase, the slot cut in the brickwork, with the top edge tucked in and wedged
  • sound pointing over the wedges, so the edge cannot lift
  • laps and joints sized to suit the movement of the sheet
  • fixings that hold the lower edge without pinching the lead

Lead moves as the weather warms and cools, and a flashing that cannot move freely will crack or lift in time. Getting that right is a matter of craft on the day, which is why we photograph each stage of a flashing job and show you the finished detail.

The way each part is laid is covered on our page about step, apron and cover flashings, and the sheet thickness for each code is in the Royston table. A flashing that is photographed at every stage leaves a record you can keep with the house papers, so the next owner knows what went in and when.

What ends the life of a flashing early

When a flashing fails sooner than its sheet should, the cause lies as much in the detail around the lead as in the lead. The signs to look for, from the ground or from the loft, are:

  • a lifted or curled edge that no longer sits tight to the wall
  • pointing that has cracked or dropped out above the lead
  • a split along a fold, where the sheet has worked back and forth
  • a stain on the ceiling or the chimney breast after rain
  • lead that has slipped out of its chase
  • moss or debris packed behind the lead, holding damp against the wall

None of those means the whole flashing is finished. A lifted edge can be refixed and repointed, and a split can be patched or a section replaced. Our page on why a lead flashing lifts goes through the causes, including what can be saved and what has to be replaced. Flashings that are clear of debris, pointed sound and free to move at the lower edge are the ones that stay in the part of the range the published figure describes.

The survey photographs the stack and its flashings at close range, so the reason it failed is photographed before any work is priced.

Patch or full replacement, and the border rules

A patch is the smaller job. MyJobQuote gives around £200 for a patch to chimney lead and around £570 on average for a full replacement, with full leadwork between £350 and £920. The page gives no VAT basis, and the figures are UK-wide guides, not prices for any one address.

A repair makes sense while the lead is sound. A full replacement makes sense when the sheet is split in several places, has thinned or the chase has failed. We tell you which it is, and where a repair is enough, a repair is what you are advised to have.

One chimney flashing is a small share of a roof, and it sits inside the approval limits in both England and Wales. The rules for a larger lead job are set out on our page about leadwork in the rain. Where a larger job is involved, the survey also says whether the stack needs scaffold, which changes the total, and the survey photographs go with the quote. The full list of lead pages is under lead roofing.

Related questions

Does 80 years mean my lead flashing is safe until then?

No. MyJobQuote says a correctly installed flashing can last for over 80 years, which describes what a good installation is capable of. It is not a minimum. Pointing, wedges and fixings can fail well before the sheet does, so a close look at the flashing tells you more than its age.

Can an old lead flashing be repaired instead of replaced?

If the sheet is sound, the answer can be a refix and a repoint, or a patch to one section. We photograph the lifted or split lead and show you before and after. If the sheet is split in several places or the chase has failed, replacement is the honest answer and you will be told.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing