01432 610152 Get a quote Call 01432 610152

Sagging gutters

What makes a gutter sag between brackets?

A gutter is held up by the brackets and the board behind it, so a dip in the line is a clue about what is underneath.

Short answer

A gutter sags because what holds it has given way. The brackets may have bent, loosened or snapped, the fascia they screw into may be soft or have dropped, the gap between brackets may be too wide, or the run may be carrying the weight of leaves, moss and standing water. Re-hanging it on the same soft board does not hold, so the cause comes first.

The brackets and what they are fixed to

Gutter brackets are small clips or arms, fixed to the fascia or the rafter ends, that carry the full weight of the gutter and anything in it. Plastic brackets can go brittle with age, and metal ones can rust or bend. When one fails, the gutter drops at that point and the rest follows.

A bracket needs a firm fixing. If the fascia is soft, the screw has nothing to bite on and pulls out under load, even though the bracket looks perfect. That is why two or three brackets can fail along the same stretch: the board behind has rotted, and the brackets simply followed it. Pulling one bracket out by hand is a bad test, since a loaded gutter above it can drop.

You can see it from the ground. Look for screw heads standing proud of the board, brackets angled away from the wall, and a fascia that is stained or flaking above the dip. Our signs of rotten fascias page gives the checks for the board, and a gutter that has already dropped by the width of a finger should be treated as unsafe to lean on.

Span, weight and the profile of the gutter

Other causes are about load. A gutter is a trough that fills with water in heavy rain, and a full run is far heavier than an empty one. If the brackets are set too far apart for that load, the gutter bows between them even though each bracket is firm.

The weight can come from within:

  • leaves, moss and grit that have built up and hold water
  • a blocked outlet that lets the run fill like a bath
  • a nest that has been added to over a season
  • a heavy material: cast iron needs strong fixings set into sound timber

A plastic gutter that has spent years in the sun can also soften and slump slightly in warm weather. A deeper or stiffer profile, or an extra bracket at the middle of a long span, is the cure on a new run. The maker's instructions give the spacing for the system, and a run that is hung wider than that will bow in time. The shape of the gutter matters here, since a half-round and a square section carry load differently.

Why a sagging gutter keeps causing trouble

A dip changes the fall. Brett Martin advises 1mm for every 600mm, so a sag of a couple of centimetres leaves a pool in the middle of the run. Standing water adds weight, and the extra weight deepens the sag. The pool also grows moss, rots the board and leaks at the joints on either side of the dip. A dip of that kind may not correct itself, since each wet spell adds a little more weight to the lowest point.

In rain it spills over the front, or soaks behind the gutter into the fascia and the rafter ends. Our overflowing gutter page and our leaking joints page follow those two symptoms.

Repair costs are lower when caught early. MyJobQuote's rate for plain uPVC guttering is around £40 to £50 per metre, and its average for a whole replacement is around £1,000 to £1,600. Both are third-party typical figures, not our prices. Re-hanging a few brackets on a sound board costs less than renewing the run, and the written quote says which applies after the survey.

Putting it right once, and the older-house caution

The order matters. We look at the board first, photograph the soft spots, and replace or repair anything that will not hold a screw. Then the brackets go back in a straight line at the right spacing, the fall is set against the outlet, and the run is tested with water before we leave, so you can watch it drain.

Do not hang from a sagging gutter or lean a ladder on it. It can fail under you, and a full run is heavy. Once the new fixings are in, every bracket is loaded by hand before the ladder comes down.

On older houses, one more check. A house from before 2000 may have gutters and downpipes of asbestos cement, and HSE accepts careful, unbroken removal of such rainwater goods as non-licensed work. Waste then follows the border: England carves asbestos out of the household consignment-note exemption, while NRW expects Welsh contractors to raise consignment notes for domestic asbestos. We stop and say so if we suspect it.

The guttering, soffits and fascias hub covers the rest of the roofline, and the site is left tidy.

Related questions

Can I straighten a sagging gutter without replacing it?

Sometimes. If the gutter itself is sound and the board behind is firm, the brackets can be reset to a straight line with a proper fall. If the plastic has bowed permanently, or the board has rotted, resetting only moves the problem along. A survey shows which applies in a single visit.

How many brackets should a gutter have?

The right spacing depends on the profile and the material, so follow the maker's instructions for the system. Cast iron needs stronger and closer fixings than plastic. A bracket at every joint, and extras on long spans, are both sensible, and closer spacing is the safer error on a run that carries a lot of roof.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing