01432 610152 Get a quote Call 01432 610152

Leaking joints

Why do my gutter joints leak?

A joint is the weakest point of any gutter run, because it relies on a seal and a bracket both staying where they were put.

Short answer

Gutter joints leak when the rubber seal inside the union has hardened or slipped, when the brackets have moved and drawn the two lengths apart, when dirt sits in the joint, or when the fall has gone and water pools against it. The drip tells you where but not why. Check the run on either side of the joint before resealing, because resealing a joint that is still moving only works for a short while.

How a gutter joint is made

Modern plastic gutter is joined with a union bracket: a clip that holds the ends of two lengths side by side with a rubber seal between them. Older metal systems rely on bolts and sealant. The joint holds water in two ways, by the squeeze on the seal and by the lengths staying in line.

Both can fail. A seal can harden and crack, get pushed out of its seat, or collect grit. Plastic also moves slightly as temperatures change, so a joint clipped too tight has no room to move, and one clipped too loose leaves the seal unsupported.

Cast iron gutter has bolted joints with a bed of sealant between the flanges. When the sealant dries out or the bolts rust, the joint weeps along the seam. Our cast iron gutters on period homes page deals with those older systems, whose joints are mended differently from plastic ones.

Knowing which type you have is the first step, because the repair for one does not suit the other. A magnet held to the gutter will tell you if it is iron, and a tap with a knuckle tells you plastic from metal.

Reading the drip: where the water ends up

A leak at a joint is easy to find on a wet day and hard to find on a dry one. Run water along the gutter from a hose, starting high, and watch each joint. The place the water escapes is not always under the joint, because it can travel along the underside of the gutter before it drops.

What the position of the drip suggests:

  • a drip at the front edge of the union points to a seal that has shifted
  • a drip from behind, down the face of the fascia, points to a back edge that is low or split
  • a drip only in a downpour points to a joint at a low point where the flow banks up
  • staining under a downpipe junction points to a blocked or poorly fitted outlet

A leak that keeps coming back after resealing points to a cause somewhere else. A sagging length or a soft fascia lets the joint move, and each time it moves the seal loses a little more of its grip. Our page on why a gutter sags follows that thread.

Repair, reseal or replace the length

If the seal is the only fault, a clean, dry joint with a new seal can be enough. That means taking the run apart, cleaning both ends, fitting a fresh seal and re-clipping to a firm bracket. It is quick when the plastic is sound. Smearing sealant over a dirty joint buys little time, and a fresh seal needs a dry, clean surface to bed down on.

If the plastic has gone brittle or cracked at the end of a length, or the brackets are weak, replacing that length is the better buy. A repair suits a run whose other parts are sound, and when it does we put it in the quote. MyJobQuote's metre rate for plain uPVC guttering is around £40 to £50, and Which? gives £75 to £350 for clearing the gutters. Both are third-party guides to typical UK costs, not our prices, and our quote waits for the survey.

Where the fascia is rotten, no joint will hold for long. The board has to be put right first, and the run refixed to sound timber, before the seal is renewed. Hose-testing the finished run is the proof, so the joints are left dry and clean and then tested with water before we pack up.

Old gutters that may contain asbestos

Under HSE advice, a building built or refurbished before 2000 is assumed to contain some asbestos, and the gutters and downpipes on older houses and garages can be asbestos cement. HSE counts removal of those rainwater goods as non-licensed work, provided the pieces come away carefully and unbroken.

That rules out sawing, drilling or scrubbing a suspect gutter, and it rules out scraping at a joint to reseal it. Material that has broken up, or is substantially damaged, is a different matter, because it falls under notifiable non-licensed work.

Disposal rules differ by country. England leaves asbestos outside its household consignment-note exemption, which covers hazardous waste "other than asbestos waste". NRW's position in Wales is that a contractor taking asbestos out of a home must use consignment notes. If we suspect asbestos at the survey, we stop and tell you before pricing. The guttering, soffits and fascias page covers the whole roofline, and a licensed firm deals with anything that needs a licence. Gutters on a garage or outbuilding are covered by the same advice, since a garage can be older than the house.

Related questions

Can I seal a leaking gutter joint myself with silicone?

Silicone over a dirty or moving joint may not last. The joint needs to be taken apart, cleaned and given a new seal, and the bracket needs to be firm. A ladder pressed against a gutter can also push the joint further out of line, so a safe stance matters.

Why does my joint only leak in heavy rain?

In heavy rain the gutter fills higher than the seal. If the joint sits at a low point, or a blocked outlet makes the flow back up, the water escapes at the weakest spot. Clearing the run and checking the fall are the first steps, and the joint is then watched through the next heavy shower.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing