01432 610152 Get a quote Call 01432 610152

Fascia choices

Capping or replacing fascias: the difference that matters

Capping covers the existing fascia board with a new face, and replacing removes it. The right choice depends on the timber behind the cover, so we start by looking there.

Horizon Roofing Hereford 9 min read

The fascia is the board that runs along the bottom edge of the roof, at the eaves. It carries the gutter, closes off the rafter ends and gives the roofline its straight line. When the paint has failed or the board has gone grey, there are two sensible routes. One is capping, which means fitting new cover boards over the old timber. The other is replacing, which means taking the old boards off and fixing new ones to the rafter ends.

Capping is the lighter of the two jobs, and sometimes it is also the right job. It is not always, because a cover can only be as sound as the board under it. A fascia with soft timber, split ends or loose fixings will keep failing under any new face, and the problem hides until the next storm.

This guide sets out how each job is done, the questions we ask of the timber, how the gutters and ventilation are affected, and the consent rules for listed buildings for England and for Wales. The wider roofline range sits on our guttering, soffits and fascias page.

What capping and replacing each involve

Capping starts with the existing fascia and soffit left in place. The old paint is scraped back, any loose pieces are fixed, and cover boards, such as uPVC, are fitted over the front and underside of the timber. Corners and joints are finished with trims, and the gutter goes back on over the top. Nothing structural is removed, so the work is quick and the old board stays as a hidden backing. The soffit can be covered in the same way when it needs it. Neither job includes tile work, unless the survey finds a fault at the eaves, in which case the lowest courses of tiles and the underlay are looked at too.

Replacing takes the old fascia off completely. We lift the boards from the rafter ends, look at what is behind, repair any damage to the rafter feet, and fix new boards. The new board may be timber, uPVC or another material, matched to the house. The soffit can come off with it, so the eaves ventilation can be re-formed at the same time. That also gives a clear view of the wall plate, the timber that carries the rafters, and of the rafter feet resting on it.

The two jobs differ most in what you can see afterwards:

  • Capping leaves the existing thickness and adds a layer, so the board stands a little proud of its old line.
  • Replacing resets the line, so boards, gutter brackets and the roof edge can be set true to each other.
  • Capping hides the old timber. Replacing shows it, and we photograph it.

When capping suits and when it hides a problem

Capping suits a fascia that is structurally sound, with a poor surface. If the board is straight, firm and dry, a cover can give it a clean new face. It suits a board that has simply faded and flaked, where removal would not buy anything the cover cannot.

It does not suit a board that has rotted. Water that has been getting behind a failing gutter or a slipped tile keeps getting there, and timber that stays damp behind a plastic face can carry on decaying out of sight. A cover does not remove the cause, so the cause is dealt with first: a blocked gutter, a leaking joint, or an eaves detail that sends water onto the board instead of into the gutter. The table sets out how we read the board.

Reading the old fascia before choosing
What we findCappingReplacing
Firm, straight, dry timberSuitsNot needed
Flaking paint onlySuitsNot needed
Soft patches or split endsHides the faultNeeded
Rafter ends damp or decayedNot suitableNeeded, with repairs

A screwdriver pressed into the lower edge of a board tells us a good deal, because soft wood along that edge is the warning sign that matters most, and a board can look fine on its painted face while it is soft beneath. Our guide to the signs of rotten fascias shows what to look for from the ground, and the photographs from the survey show you what the ladder reveals.

What happens to the gutters and the fall

The gutter hangs from the fascia, or from brackets screwed through it to the rafter feet. Any change to the board changes the gutter's support, so the gutters are always taken down for either job. That is also the best time to check the fall. The gutter maker Brett Martin gives the fall as "1mm for every 600mm", which works out at 10 millimetres over a six metre run. A gutter fixed to a capped board that has itself sagged inherits the dip.

With capping, the gutter brackets must reach sound timber. Screws that bite only into the cover and the old fascia will hold for a while and then pull. Where the old board is replaced, brackets can go straight into the rafter feet, which is a firmer fixing than a screw through a thin board. The fixings need to find the rafter feet, so we locate them before the cover goes on and mark them. A gutter full of water is heavy, and a bracket that has pulled even slightly changes the fall.

With replacement, the new board is set to the gutter line first. We fix it to a level that matches the roof and then step the gutters down toward the outlet, starting at the highest point. Our guide to fascia capping cost explains what moves the price of the two jobs.

A gutter that overflows at the joints, or a damp patch on the wall below, can point back to the eaves rather than the gutter itself. Downpipe positions are checked too, because a pipe that is moved by a few inches changes where the water lands.

Soffits, ventilation and what is behind the board

The soffit sits beneath the fascia, closing the underside of the overhang so that birds, weather and debris stay out. Both fascia jobs touch it, so we look at the soffit before choosing. For a cold roof, Marley's figure is a continuous opening of 25mm along the eaves at pitches of 15° or less, and 10mm above that pitch, with high resistance underlay. A cover that closes up an existing vent gap, or a new soffit without vents, can cut off that airflow, and moisture then builds in the roof space.

Replacing is the moment to put ventilation right. Capping can include vented soffit covers, as long as the opening is not blocked by the cover or the old paint. Soffit panels that come out and are not suspect go out as ordinary waste, while anything that might be asbestos is held aside until it has been identified. A separate guide to soffit vents and roof ventilation explains the choices.

Two more things are checked behind an old board, because either one can change the plan:

  • Old white panels under the eaves can be asbestos insulating board, and taking that board down is usually licensed work. See the guide to asbestos soffits. The survey comes first.
  • Birds and bats may be using the gap behind the board. The Wildlife and Countryside Act 1981 covers both countries: a nest is protected "while that nest is in use or being built" from anyone acting intentionally, and bats have their own protection.

Consent, materials and what the work costs

On a listed building, changing a fascia can need listed building consent. In England, that comes from section 7 of the Planning (Listed Buildings and Conservation Areas) Act 1990. In Wales, the Historic Environment (Wales) Act 2023 applies from 4 November 2024, under sections 88 and 89. For any listed house, check with the council before a board is ordered, because a plastic cover on a timber roofline may not be accepted. In a conservation area, ask the council as well, and for a house in the Bannau Brycheiniog National Park, ask the National Park Authority. Herefordshire has 64 conservation areas, so a roofline in a village centre is worth checking before an order is placed.

For cost, we quote third-party figures only. MyJobQuote gives "around £800" as the average cost of capping fascias and soffits. A uPVC fascia retailer, who has an interest in the answer, says boards "typically maintain reliable performance for between 20 and 40 years". Neither is a promise for your house, and neither figure says what the work will cost here.

Our written price is one total after the survey. Several things move the price: the length of roofline, the height, the number of corners and the material. The state of the rafter ends matters as well. Scaffold forms part of the written price. Where it stands over a public road or path, we arrange the licence with our scaffolder. Check that any quote says whether VAT is included.

How we choose on the day of the survey

The choice is made from what we see, not from a standard recommendation. The order we follow is simple.

  1. Walk the roofline from the ground and photograph each elevation.
  2. From the ladder or scaffold, press a probe into the lower edge of the fascia and the rafter ends.
  3. Check the soffit, the vents and any gap where birds could be entering.
  4. Look at the gutter fall, brackets and downpipe positions, and at the ends where the roofline turns a corner.
  5. Decide, elevation by elevation, whether capping is sound or whether the board has to come off, and note which gutter lengths go back and which are renewed.

A house can need both. A front elevation with sound timber may take capping while the back, where a downpipe has overflowed for years, needs new boards. You see the photographs for each elevation and decide with them in front of you. The notes also record the colour and profile of the existing boards, so that new ones sit properly against the neighbouring house or the next elevation.

Where replacing is the better buy, that is the advice. Where capping is enough, the heavier job is not suggested. Both options are priced as one total on the written quote, so they can be compared on the same basis. If the house has a mix of materials, say timber at the front and plastic at the back, we note it, so the new run does not clash with what stays. Where a new roof is planned too, the scaffold stands on site anyway, and the fascias are timed with it.

Capping and replacing: your questions

Will capping stop my fascia rotting?

Capping changes the face, not the timber. If the board behind is dry and sound, a cover protects the surface. If the wood is already wet or soft, the cover can hide further decay. That is why the lower edge and the rafter ends get probed before capping is recommended, and why the photographs go to you.

Do I need consent to replace fascias on a listed house?

You may do. In England, listed building consent comes under section 7 of the 1990 Act, and in Wales under sections 88 and 89 of the Historic Environment (Wales) Act 2023. Ask the council before choosing a material, because a plastic board may not be accepted on a period roofline.

Can the gutters stay up while the fascia is done?

No. The gutter hangs from the fascia or its brackets, so it comes down for either job and goes back on once the board is fixed. That is also the point at which the fall is reset toward the outlet, using the fall that Brett Martin gives.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing