In brief
Expect roughly 10 to 15 years from HomeBuilding's table and 10 to 20 years from Less, which adds that the answer turns on the felt and the fitting. Neither range is a promise. A felt roof built from several layers, laid on a sound deck with tidy edges and flashings, sits towards the long end of that span. A single thin layer sits towards the short end. We read the layers, the laps and the blisters on your own roof.
Two lifespans, one condition from Less
Bitumen sheet goes down on this type of roof with a gas torch passed over it as the roll unwinds: the underside softens and fuses to the layer beneath. A modern roof is built in several layers, and the cap sheet carries a mineral finish that shields the bitumen from sun and rain. A flat deck of boards or ply sits under the lot.
| Source | Lifespan given |
|---|---|
| HomeBuilding | 10-15 years |
| Less | 10 to 20 years, depending on quality and installation |
The condition in the Less entry matters as much as its figures. It ties the span to the quality of the felt and the way it was fitted, which are things we can judge on site. Two felt roofs laid in one summer can end up in very different states for that reason alone, one still tight at 15 years and the other splitting at 10.
Both are ranges, not promises, and neither says anything about the deck underneath. A felt roof that has outlived its covering may still sit on boards that are fine to keep.
What we read on a felt roof of any age
Felt shows its age on the surface, and the signs can be read from a ladder before anyone steps onto the roof. Here is what we look at and photograph:
- the mineral finish: bare, shiny bitumen where the granules have worn away
- blisters, which are pockets of trapped moisture or air under the top layer
- splits along the laps, where one sheet overlaps the next
- the turn-up at walls and the flashing that finishes it
- puddles that stay after rain, which age felt faster than a free-draining surface
A blister is not always a leak, and what makes a flat roof blister explains when one is cosmetic and when it has opened. Splits and bare patches matter more, because they let water reach the layers underneath. We take a photograph of each finding as we meet it, so you can follow the survey from your phone and see how the layers have weathered from the cap sheet downwards. Where the top layer has worn through to the one beneath, we show that edge close up, because it tells you how much of the build-up is left to protect the deck.
What felt costs to repair and to renew
Costs come from third parties, and each is named here. A Which? survey of Trusted Traders in November 2025 puts a felt roof for a typical single garage, 6 m by 3 m, at £1,400 to £3,500, ex VAT. MyJobQuote's flat roof page, updated on 20 October 2026, says to expect £80 to £120 per m² for installed felt.
That per m² rate is a unit price, not a roof price. Multiplying it by an area gives a number nobody should rely on, because edges, upstands, outlets and rotten boards all change a roof. Our own price follows the survey and arrives as a single written total.
Plenty of felt roofs are a repair job rather than a replacement. A split along one lap or a patch of worn finish can be mended and given more years, as long as the layers around it are still bonded and the boards below are dry. A wet deck changes that, because new felt over damp boards traps the moisture again. When the whole surface is bare, blistered and splitting, renewing it makes more sense, and you get that advice in plain terms. The detail sits on our page about felt flat roof cost per m2.
Renewing felt: England and Wales differ
New felt over a flat deck is renovation of a thermal element, and the insulation rules come with it. In England, Approved Document L (2021 edition) allows a lesser upgrade where 0.16 is not feasible, provided it pays back within 15 years, and expects the result generally to be no worse than 0.7. In Wales, gov.wales warns that replacing a roof with integral insulation can mean upgrading that element too.
The approval route differs as well. In England, the Planning Portal's test is 25 per cent of the building envelope and 50 per cent of the roof, and work staying under both does not normally need an application. In Wales, the Welsh Government's re-roofing page begins from the opposite point: approval will be needed in most situations. Old felt stripped back to the deck also gives a chance to check the insulation below it, so the building control conversation covers that too.
We ask the council's building control service, or a registered building control approver, before starting. Our torch-on felt roofs today page describes the layered systems on offer, and the flat roofing hub sits above all of these.
