Callers about a failed flat roof tend to expect a new covering and nothing else. The Building Regulations see it differently. A flat roof is a thermal element, a part of the building that keeps heat in, and when the waterproof layer on it is renewed the law treats the job as renovation. Renovation can carry a duty to bring the insulation up to a stated standard at the same time.
That duty is set out in Approved Document L, the Building Regulations guidance on saving fuel and power. England and Wales each publish their own edition, with different numbers and different paragraph references. A house in Hereford follows one set; a house across the border in Monmouthshire or Powys follows the other.
This guide sets out the figures for each side, the tests that decide when approval is needed, how the extra insulation can be built into the roof, and the dates on which new editions begin. It sits beside our flat roofing pages, which cover the work itself from survey to finish.
A new membrane is renovation in both countries
In regulation 2 of the Building Regulations 2010, a thermal element is any wall, floor or roof. Windows, doors, roof windows and rooflights are counted separately. A flat roof therefore qualifies, so what matters is which kinds of work on it trigger the rules. Three things set the tone for everything that follows: the roof has a heat-loss figure, the figure can be improved, and the law looks at the roof as a whole element and not at one corner of it.
England's Approved Document L, in its 2021 edition with 2023 amendments, lists among its examples of renovation a new waterproof membrane laid on a flat roof in place of the old. The document took effect on 15 June 2022 for use in England.
Wales words it in its own edition, the 2022 edition with 2024 amendments, which took effect on 23 November 2022. Its paragraph 11.16 takes renewal of the covering membrane on a flat roof to be the replacement of a layer already there. The Welsh Government's re-roofing page warns that replacing a roof which has insulation built in may mean bringing that thermal element up to standard.
The plain reading is therefore shared by both countries. A new covering over a flat roof is not treated as a simple repair. Other jobs are judged on their own:
- a patch over a split
- a resealed seam
- a replaced flashing or edge trim
Our guide to whether a new membrane is a renovation goes through that dividing line in more detail. The rest of this page deals with the stricter case, where the whole covering comes off.
England: the figures and the way out
England uses two tables, and which one applies depends on whether the roof is new work or an existing element being renovated. The numbers are U-values, which measure heat lost through a surface in W/m²K. Lower is better.
| Situation | Table | Figure |
|---|---|---|
| Roof newly built onto an existing house | 4.2 | 0.15 |
| Existing roof, threshold | 4.3 | 0.35 |
| Existing roof, improved value | 4.3 | 0.16 |
Table 4.3 is the one for renovation. Read plainly, a retained roof that is worse than 0.35 is brought up to 0.16 when it is renovated. Where the flat roof carries glazing, Table 4.2 gives 2.2 for a rooflight and, for a roof window, 1.4 or WER Band B. Both are separate from the roof figure, and a replaced rooflight is a separate piece of work with its own value to meet.
Paragraph 4.13 offers a way out. If the upgrade cannot be done technically or functionally, or the saving would take more than 15 years to repay the cost, the target falls back to the best U-value achievable that can still pay for itself within 15 years. After any upgrade the figure should generally not be above 0.7.
Nothing in the text lets a builder skip the question, and a quote that never mentions insulation on a full re-cover has skipped it. If the relaxation is used, the reasons are for the building control body to accept, and we put that question to them before the quote is agreed and not after the work.
Wales: a different set of figures
Wales has its own tables and its own logic. Welsh Approved Document L, Volume 1, 2022 edition with 2024 amendments, gives these roof figures.
| Situation | Table | Figure |
|---|---|---|
| Roof newly built onto an existing house | 4.1 | 0.13 |
| Retained flat roof, maximum | 11.1, column (a) | 0.16 |
| Retained flat roof, limiting | 11.1, column (b) | 0.35 |
The Welsh table works differently from England's. Here 0.35 is the limiting value, the worst result acceptable when 0.16 cannot be reached. It is not a trigger that sets an upgrade off. Glazing figures match England's: 2.2 for rooflights, and for roof windows 1.4 or WER Band B.
What sets the upgrade off is paragraph 11.14. The whole element should be improved once the renovated area passes 50% of that element's surface, or where the work is a major renovation.
Paragraphs 11.20 and 11.21 supply the relaxation, and the wording is strict about reasons. If column (a) cannot be met on economic, functional or technical grounds, the roof goes to the best standard that can, and generally should not be worse than column (b). The economic test is a payback of the initial cost within 15 years through energy savings.
The first Welsh figure to remember is 0.13, because it belongs to new roof work and not to a renovated one. The second is 0.16, which is the value the Welsh table aims for on a renovated flat roof unless building control agrees it cannot be done.
Where the extra insulation goes
Meeting a U-value on a flat roof means adding thickness, and thickness has to go somewhere. The layout decides how awkward that is.
- Above the deck, as rigid boards under the membrane. This is the common route on a re-cover, because the old covering comes off anyway and the boards go straight onto the deck. Our guide to warm deck or cold deck explains the appeal.
- Between the joists, under the deck. This needs the ceiling opened up or the work done from the room below, and a cold space must stay ventilated.
- Tapered boards, which add insulation and restore the fall in one step.
Added thickness changes what meets the roof, and a roof edge carries more junctions than a first glance suggests. Door thresholds, window sills, upstands against walls and the height of edge trims all sit at set levels. A roof that rises by the thickness of new boards may need lifted flashings, raised upstands or a re-formed edge, and on a house with a low eaves line it may clash with a window head.
We check these levels at the survey, photograph each junction and tell you what must move. If the insulation drawn for the roof cannot physically fit, that is the moment to raise the relaxation questions in the two sections above, and not later when boards are already on site. A rooflight set into the deck needs the same care, because its kerb has to rise with the roof around it.
Approval, building control and who to ask
England and Wales also differ on when a roof job needs an application at all. The Planning Portal puts the no-application case this way for England: "Less than 25 per cent of the total 'building envelope'" is affected and "Less than 50 per cent of the roof is affected". A whole flat roof fails the second test, so it goes to building control. The Portal's roof page sets out both tests.
In Wales, the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval." It also accepts that certain flat roof repairs fall outside the application route, which is one more reason to keep repairs and replacement apart.
Who handles the application depends on the address. Herefordshire Council Building Control is on 01432 261938. Forest of Dean Building Control is on 01594 812315 and Shropshire Council Building Control on 01743 258710. Across the border, ask the council's building control service or a registered building control approver, and that holds for Powys addresses too.
Private building control is open to owners in both countries. In England, approvers register with the Building Safety Regulator, a regime that began on 6 April 2024. In Wales the Welsh Ministers regulate the councils, and a new Welsh building control regime began on 1 July 2026. In either country, a registered building control approver can inspect and sign off work in place of the council.
Dates ahead and what goes into the quote
Both countries have new editions coming. England's Approved Document L 2026 takes effect on 24 March 2027 for building work that is not higher-risk work. Its tables are renumbered, with Tables 3.2 and 3.3 replacing 4.2 and 4.3, and the payback rule moves to paragraph 3.14. The roof figure for new work stays at 0.15.
Wales brings in its next edition on 4 March 2027. Until the relevant date, the editions described above are the ones in force, so those are the figures to quote today. A job that straddles a date is worth raising with building control before the price is agreed.
For the price itself, the written price comes as one total after the survey visit. For a re-cover that triggers insulation, the quote should state the thickness and the U-value being aimed for, whether the layer goes above or below the deck, and whether VAT and scaffold are included.
Ask for that wording in any quote you compare, and keep the Approved Document L edition named in each one so that like is set beside like. A quote that says only "new felt" or "new rubber" has not shown you whether the insulation question has been answered. If the roof is ageing and a repair is the better buy, we say that plainly and leave the regulations out of it. Our guide to flat roof insulation rules in Wales takes the Welsh side further.
