01432 610152 Get a quote Call 01432 610152

Deck design

Warm deck or cold deck: where the insulation goes on a flat roof

Every insulated flat roof makes one choice early: insulation above the structural deck or below it. This guide compares the two layouts and what each means for condensation, height and cost.

Horizon Roofing Hereford 9 min read

The terms warm deck and cold deck sound like jargon, yet they describe a single decision with lasting consequences. It is the position of the insulation relative to the structural deck, the boards or slab that carry the roof. Put the insulation above the deck and the deck stays on the warm side of the building. Put it below, between the joists, and the deck sits outside the insulation and runs cold.

The first layout is a common specification for new flat roof work, and the second is a layout found on older roofs. If you are replacing a covering on a house that has a cold deck, you will be asked, or ought to be, whether to keep that layout or change it.

The sections below explain what each layout is, how each handles moisture, what the choice does to the height of the roof edge and the cost of the job, and what Part L asks in England and what it asks in Wales. For the range of coverings and repairs, see our flat roofing page.

Two layouts, one question

Both layouts use the same ingredients: a deck, insulation, a vapour control layer, a waterproof covering and a ceiling below. The vapour control layer is a sheet that slows the movement of warm, moist air from the rooms into the roof build-up. What differs is the order they go in, and the order determines where the deck sits in relation to the cold.

Where each layer sits
LayerWarm deckCold deck
Waterproof coveringTopTop
InsulationAbove the deckBelow the deck, between joists
Structural deckBelow the insulation, warmAbove the insulation, cold
Air spaceNone neededVentilated void between deck and insulation
Vapour control layerOn the deck, under the insulationOn the room side of the insulation

In a warm deck, the whole sandwich is stacked on top of the structure, so the timber stays at roughly room temperature all year. In a cold deck, the structure is exposed to outdoor temperatures from above, and a gap above the insulation is meant to carry moist air away. Ask a roofer which of the two a quote assumes, because a quote that does not say leaves the layout to be decided on the roof. Both layouts can give a sound result when built to their own rules.

A third layout, the inverted roof, puts the insulation on top of the waterproof layer. It is a specialist arrangement, found on terraces and roofs with ballast, and is not the subject here.

How a warm deck works

The warm deck is built from the top of the structure up. The vapour control layer goes onto the deck first, then rigid insulation boards, then the waterproof covering. Everything beneath the boards remains at roughly the temperature of the room.

That is its main advantage. Condensation forms where warm, moist air meets a cold surface. In a warm deck, the surfaces of the structure are kept warm by the boards above, so there is less chance of moisture condensing on the timber. The vapour control layer adds to that by slowing the passage of moist air from the house into the roof.

There are practical benefits too.

  • The work can be done entirely from above, without disturbing the ceiling or the room below.
  • The insulation is continuous across the joists, so there are fewer gaps where heat can escape.
  • No ventilated void is needed, and so no eaves vents that could be blocked by later work.
  • Tapered boards can be used to restore a lost fall at the same time as the insulation goes on.

The costs are height and weight. Insulation on top of the deck raises the roof surface, and the edges, upstands and flashings have to be raised with it. A doorway onto a flat roof may lose its step. That is where the survey earns its keep, because those heights decide whether the layout is workable at all.

How a cold deck works, and where it goes wrong

In a cold deck the insulation is laid between and sometimes beneath the joists, with a ventilated gap above it, so that moist air which gets past the ceiling can escape before it condenses on the underside of the deck. The air path is the key, and the cold deck depends on it completely.

That dependence is the weakness. If the gap is blocked, by insulation pushed up against the deck or by a vent covered in a later repair, the air stops moving. Moisture then settles on the cold boards, and over time the timber can darken, soften and rot. The first sign in the room below may be a damp patch on the ceiling that looks just like a leak.

Telling damp from a leak

Our guide to condensation under a flat roof sets out the signs that separate condensation from a leak.

A cold deck is not a mistake. Kept clear and ventilated, it can serve a roof well. It is a layout with a requirement, and the requirement must be kept. When the covering comes off a cold deck, the roofer can see whether the void is clear and whether the vapour control layer is intact. Those findings decide whether to keep the layout or to move to a warm deck, and we photograph them so you can see for yourself.

The thickness of insulation that fits between joists is limited by the joists' depth, which is why a cold deck can struggle to meet modern U-values without additional boards.

Height, cost and disruption compared

Neither layout wins on every count. The choice depends on the house.

The two layouts compared in use
QuestionWarm deckCold deck
Work from above only?YesNot if the ceiling is opened
Roof edge rises?Yes, by the board thicknessLittle or not at all
Reliance on ventilation?NoneTotal
Condensation risk in the deck?Lower, with a sound vapour control layerHigher if the void is blocked

On cost, the sources give only ranges for the whole job. Which? reported £1,400-£3,500 for a garage roof in felt, measuring 6 m by 3 m, and £1,950-£4,000 where the covering is PVC or rubber EPDM (November 2025 survey, excluding VAT). MyJobQuote puts the average flat roof replacement in 2026 at £1,500 to £6,000. None of these figures separates the insulation layout, so none can be used to price the choice.

What we can say is that the warm deck asks for more material above the deck, while the cold deck asks for access below it. Which costs more depends on the house, and the written price arrives as one total after the visit, so the comparison is made on your own roof and not on an average.

Ask any contractor which layout is proposed, and ask for it in the quote. Where a ceiling has to be opened for a cold deck, the cost of making good the plaster belongs in the price, and a quote that leaves it out is incomplete. Where boards go above the deck, the cost of raising the edges and flashings belongs there instead.

What Part L asks, in England and in Wales

If the covering on a flat roof is renewed, a thermal element is being renovated, and the insulation figures apply. Which of them applies depends on the country. The layout you choose affects how easily they can be met.

In England, Approved Document L (2021 edition) gives Table 4.3 for existing elements: a roof threshold of 0.35 and an improved value of 0.16 (W/m²K). Table 4.2 gives 0.15 for roof work that is new on an existing house. Paragraph 4.13 gives a relaxation where the upgrade cannot pay back within 15 years.

In Wales

In Wales, the Welsh Government's Approved Document L, Volume 1, gives 0.13 in Table 4.1 for a roof newly formed on an existing house and, for retained roofs in Table 11.1, 0.16 with 0.35 as the limit where 0.16 cannot be reached. The 2022 edition took effect on 23 November 2022.

A warm deck reaches these numbers more easily in both countries, because the boards sit on top of the structure and are not limited by the depth of the joists. A cold deck can need a combination: insulation between the joists, and extra boards below or above.

Both countries are due new editions. England's Approved Document L 2026 takes effect on 24 March 2027, and Wales follows on 4 March 2027. Our guide to replacing a flat roof and the insulation rules sets the figures out side by side.

Choosing for your own roof

The right layout comes from the survey, not from a preference. These are the findings that tip the balance.

  • Soft or stained timber under the old covering points to moisture, and to a decision about the ventilation path.
  • A low door threshold or a window head close to the roof edge limits how much height can be added.
  • A ceiling in good order, with a room below that the owner does not want disturbed, favours working from above.
  • A roof with an existing ventilated void that is clear and sound may be kept as a cold deck if the figures allow.

When we open a roof, we photograph the deck, the insulation and the vapour layer, and show you what is there. If a cold deck is working and the figures can be met, we tell you that plainly. If the void is blocked or the timber is damaged, we show you the evidence and set out the warm deck option with the changes to the roof edge it brings.

Ask for the proposed layout, the insulation thickness and the U-value to be written into the quote, with a note of whether VAT and scaffold are included. Our guide to flat roof falls and drainage is worth reading beside it, because the fall is built into the same layers.

Before any such job starts, we check with building control, either the council or a registered building control approver, and we raise any proposed use of the relaxation clauses with them at that point.

Warm and cold decks: your questions

Can I change a cold deck roof to a warm deck when I replace the covering?

Yes, if the roof edge, thresholds and flashings can rise by the thickness of the new boards. It means lifting the old covering, fitting a vapour control layer to the deck and laying insulation above. The ceiling below stays untouched. We check the heights at the survey before suggesting it.

How would I know if my cold deck is failing?

Look for ceiling stains that appear without rain, a musty smell in the room below, or timber that is dark and soft when the covering is lifted. These point to moisture trapped in the deck. A survey with photographs of the deck, the void and the vapour layer will show which it is.

Do I still need a vapour control layer with a warm deck?

Normally yes. It sits on the deck beneath the insulation and slows moist air passing from the house into the roof. The specification for your roof should name it, along with the insulation and its thickness, so the quote shows what is being laid and in what order.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing