01432 610152 Get a quote Call 01432 610152

Falls and drainage

Falls and drainage on a flat roof: 1:80 finished, 1:40 designed

Even a roof called flat needs a slight slope so rain can reach an outlet. This guide covers the 1:80 finished fall, the 1:40 design fall, and how outlets and gutters finish it.

Horizon Roofing Hereford 9 min read

Every flat roof is built to shed water, and the shedding depends on a slope too gentle to notice from the garden. The slope is called a fall. It is expressed as a ratio, such as 1:80, which means one unit of drop for every 80 units of run. On a roof 4 metres deep, a fall of 1:80 is a drop of 50 millimetres from the high edge to the low one. If the fall is missing or has been lost, water stays on the membrane, and standing water ages a covering faster than running water does.

Two figures are quoted in the trade, 1:80 and 1:40, and they can be muddled. One is a minimum for the finished roof. The other is what a designer is advised to aim for so that the first is reached. The difference matters at quote stage, because a fall drawn at the lower figure can finish below it on the roof.

The sections below set out where the figures come from, what the current standard covers, how falls are built, where the water goes next, and what the rules ask in the two countries when a membrane is replaced. For the wider range of work, see our flat roofing page.

Two fall figures, two different jobs

The finished fall is what the roof has when it is done and the covering is down. The NFRC, the roofing trade body, reports that BS 6229:2025 sets a minimum 1:80 finished fall, across general roof areas and internal gutters alike. That is the floor for the completed roof, not a target to design to.

The designed fall is what goes on the drawing. IKO, a membrane manufacturer, advises a design fall of 1:40 for anyone who wants to reach 1:80. IKO is advising here, and it links the 1:40 to the code of practice, while the 1:80 finished minimum is the figure NFRC reports from BS 6229:2025. Built roofs may not match their drawings exactly, which is the context for the larger figure.

The two fall figures compared
FigureWhose it isWhat it means
1:80BS 6229:2025, reported by NFRCMinimum finished fall
1:40IKO's adviceFall to design for

A roof designed at 1:40 has twice the slope of the 1:80 minimum. That extra margin absorbs the small errors in a timber deck, a bit of movement in the structure and the thickness of laps and joints. A roof designed at exactly 1:80 has no margin, so any shortfall in building leaves it below the minimum. When a quote says the roof will be laid to a fall, we say which figure it means and how the fall will be measured.

What BS 6229:2025 covers and what it leaves out

BS 6229 is the British Standard for flat roofs whose waterproof covering is flexible and fully supported by the deck beneath. The current edition is BS 6229:2025, and its scope takes in flat roofs and gently curved ones, up to a pitch of 10 degrees. The 2018 edition was withdrawn on 16 December 2025, so a specification that cites the 2018 edition is out of date, and it is worth asking a supplier which edition their details follow.

The standard is about membranes: felt, single-ply and the like, laid over a continuous deck. It does not govern lead. Lead roofing sits outside BS 6229, and Approved Document C refers to BS 6915:2001 for lead sheet. Lead flat roofs, gutters and box valleys therefore follow lead-specific guidance, such as the Royston Lead table that sets sheet codes by use, with Code 5 and above listed for parapet gutters, box gutters and tapered valley gutters.

Three points follow for owners:

  • A roof covering of EPDM, GRP or felt is a membrane roof, and the BS 6229 fall applies to it.
  • A lead-covered flat roof or gutter follows the lead guidance, so the fall is set differently.
  • The standard sets a minimum for the finished roof, and it does not say that a fall at the minimum is ideal.

Our guide on what fall a flat roof needs answers the same question in short form, and the sections here go into why the numbers are what they are.

Where a fall comes from in the build

A fall is built into a flat roof, never added afterwards by wishing. There are three ways to make one, and which suits a roof depends on the structure and the insulation.

  • Sloping joists: the structure itself is laid to the fall, which is the cleanest route on a new roof.
  • Firrings: tapered timber strips are fixed on top of level joists, so the deck above them slopes.
  • Tapered insulation: boards cut to a slope are laid on a level deck, so the fall comes with the insulation layer.

On a replacement, the choice is made by what is already there. A timber deck that is sound and falls the right way can be kept. A deck that has sagged between joists, or fallen back towards the wall, may need new boards or a firring layer before the membrane goes on. This is why a survey of the structure comes before a quote, and why we take photos of your own roof, including the underside where we can reach it, with the pictures shared with you.

A fall has to be measured, not assumed. A long straight-edge or a laser level run across the deck shows the slope in plain figures, and a few pints of water poured on the deck show where it runs and where it stops. If water sits near the outlet, the fall near the outlet is wrong, whatever the average across the roof says. The same check, repeated after the new deck is down and before the membrane, is how we confirm the finished fall.

Outlets, gutters and the way off the roof

A fall does nothing unless it leads somewhere. The water has to reach an outlet, a gutter or a downpipe, and each of these has its own requirements. The simplest layout is a single slope running to an edge gutter. More complex roofs drain to an internal gutter, a scupper through a parapet, or a drain in the middle of the deck, and each of those adds places where a blockage or a low spot can hold water.

Gutters have a fall too, a gentler one. Brett Martin, a gutter manufacturer, advises 1mm for every 600mm. That is a long way below the roof's 1:80, so a gutter fed by a roof that is falling correctly can still hold water if it is laid flat or backwards. When we replace a flat roof, the edge gutter or trim is set to its own fall and checked against the outlet height.

Details to look at on any flat roof:

  • the outlet or downpipe: is it clear, large enough and lower than the surrounding membrane?
  • the internal gutter: does it have its own fall to the outlet, and does it meet the same 1:80 minimum?
  • the upstands: do they leave a path for water to reach the outlet, or do they trap it?
  • the overflow: if the main outlet blocks, where does the water go next?

Our guide to where a flat roof should drain covers the choices between edge gutters, parapet outlets and internal drainage. A roof with an outlet that is blocked by leaves behaves like a roof with no fall, so keeping outlets clear is part of the roof's care, not an extra.

Reading a roof that holds water

A pool standing on the deck is a sign to read, not a verdict. A shallow film that dries within a day is different from a pool that sits for weeks, and the pool has a cause. The cause falls into one of three groups: the original fall was too small, the deck has moved since it was laid, or an outlet is blocked or set too high.

Staining on the membrane shows where water has stood. Tidemarks, algae and dirt gather at the edge of a pool, and a roof with several such marks has a pattern that points to a deck problem and not to a one-off blockage. On a repair, patching the membrane over a hollow treats the symptom only, because the hollow will refill. Our guide to ponding water on a flat roof goes through what it does to each covering.

When we survey, we do three things in order:

  1. Walk the roof, if it is safe to do so, and photograph the pools and the stains.
  2. Check the fall with a level along the line the water should take, and note the low points.
  3. Look at the outlets, gutters and downpipes, and clear or note any blockage.

The answer then falls into one of two groups. If the problem is local and the deck is sound, a repair or a local build-up may be enough. If the fall is wrong across the roof, replacing the covering without correcting the fall repeats the problem, and the honest recommendation is to rebuild the fall as part of the job.

Rules, costs and lifespans when a membrane is replaced

Fitting a fresh waterproof layer to a flat roof is renovation work on a thermal element, and the insulation targets can follow. The two countries set them differently.

Renovating a flat roof under Part L
PointEngland, AD L 2021Wales, AD L
Membrane replacementCounts as renovationPara 11.16 includes it
TargetsTable 4.3: threshold 0.35, improved 0.16Table 11.1: 0.16, not worse than 0.35
RelaxationPara 4.13: 15-year paybackParas 11.20 to 11.21: 15-year payback

The Welsh Government adds that some repairs to flat roofs will not need an application, while replacing a roof that has integral insulation may bring a requirement to upgrade the thermal element. Building control, run by the council or a registered building control approver, decides what applies.

On price, Which? surveyed Trusted Traders in November 2025 and found that a single-garage roof in felt came in at £1,400 to £3,500, excluding VAT. MyJobQuote gives £1,500 to £6,000 as the 2026 average for flat roof replacement, with felt at £80 to £120 per m². The per m² figure is not a total, and we do not multiply it. The quote we give is a single figure in writing, after the survey.

For lifespan, HomeBuilding gives EPDM 25 to 30 years and Less gives 30 to 50, which shows how far sources disagree. HomeBuilding gives GRP 25 to 30 years against Less at 25 to 40, and felt 10 to 15 against 10 to 20. These are typical ranges, not promises.

Questions on flat roof falls

Is 1:80 the fall a flat roof should be designed to?

No. NFRC reports 1:80 as the minimum finished fall in BS 6229:2025. IKO advises a design fall of 1:40 for anyone who wants to achieve 1:80. The two numbers do different jobs, and a good specification names both and says which one it means.

Does the same fall apply to a lead flat roof?

Not through BS 6229, which covers membranes only. Lead is covered by its own guidance, and Approved Document C refers to BS 6915:2001 for lead sheet. A lead roof or gutter is set out to that guidance, so ask for the lead details to be written out separately.

Can a new membrane fix a roof that holds water?

Only if the fall is sound. A new covering laid over a hollow or a roof with too little slope will hold water again. The fix is to correct the fall, with new firrings or tapered insulation, as part of the replacement, and to keep the outlets clear.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing