01432 610152 Get a quote Call 01432 610152

Felt roofing

Torch-on felt roofs today: built-up layers and where felt still fits

Torch-on felt is the oldest of the modern flat roof coverings and still in use. This guide explains the layers, the lifespan figures, and the jobs where felt remains a sound choice.

Horizon Roofing Hereford 9 min read

Felt roofing has been laid on flat roofs for a long time, and the name hides how much has changed. Modern torch-on felt is not the thin tarred paper of older garages. It is a bitumen sheet reinforced with a fabric or polyester core, rolled out in layers and joined by heat. The result is a covering that is built up on the roof rather than delivered in one piece.

That layered construction is the thing to understand. A felt roof gets its protection from several sheets working together, each one lapped over the one before, with the top sheet taking the weather. When it works, the layers share the load. When one fails, the others buy time, though not unlimited time.

The sections below set out how the layers go down, how long felt lasts according to two named sources, where felt remains a good fit, where another covering is a better answer, and which rules apply when felt is replaced in Herefordshire and in the Welsh border counties. The wider choice is covered on our flat roofing page.

What built-up layers actually are

A built-up felt roof is a stack. Each layer has a job, and a weak joint lets the whole stack down. The exact specification varies with the roof and the product, so the list below describes the general order and not a single recipe.

  1. The deck, such as timber boards or sheet material, laid to a fall.
  2. A vapour control layer where insulation is used, to stop warm damp air from the house reaching cold surfaces.
  3. Insulation, when the design includes it.
  4. A base layer of felt, which is fixed to the deck or the insulation.
  5. One or more further layers, with the final cap sheet on top, which can be surfaced with mineral granules that shield the bitumen.

The sheets are lapped, with the joints staggered from one layer to the next, so that no seam sits directly over another. At walls and upstands the felt turns up and is finished beneath a flashing. At edges it runs to a drip trim.

Two things follow. First, every lap is a place where bond matters, so the roofer checks each one after laying. Second, a cap sheet that has lost its granules, cracked, or lifted at a lap tells you the top layer is being asked to do more than it can.

BS 6229:2025 applies to roofs of this kind, because its scope is flat roofs whose flexible waterproof layer is supported along its whole length, and NFRC reports its minimum finished fall as 1:80.

Torch-on, adhesive and self-adhesive laying

The phrase torch-on describes how the layers are bonded. A gas torch softens the underside of the roll as it is unrolled, so that the bitumen flows and sticks to the layer below. It makes a strong bond, but it also puts a naked flame on a roof, which is why the choice of method is a safety decision as well as a technical one.

Where timber, insulation or an old building sit close to the work, there are other ways to bond felt.

  • Hot-bonding with a torch, the traditional method for a bonded cap sheet.
  • Cold-applied adhesive, which avoids flame at the cost of a longer wait while it cures.
  • Self-adhesive sheets, which stick on contact once the backing is peeled away.
  • Mechanical fixings for the base layer, to hold it to the deck before the cap sheet goes on.

No method is right for every roof. On a garage with timber eaves and a flammable fascia, we would look hard at a flame-free option. On a clear roof with a masonry parapet, a torch may be fine.

You are entitled to ask which method will be used and why. The answer should appear in the written quote, with the number of layers and the type of cap sheet. A quote that says only "felt roof" does not tell you which of these you are buying, and it makes a comparison with another quote meaningless. Ask also how the laps will be checked, and whether the edges are finished with a trim or with a bonded strip.

How long felt lasts, by two named sources

Felt has the shortest life of the common flat roof coverings in the published figures, and the two sources below disagree on the range. HomeBuilding gives 10-15 years. Less says that torch-on felt lasts 10 to 20 years depending on quality and installation.

Felt lifespan, two published figures
SourceFigure
HomeBuilding10-15 years
Less10 to 20 years, depending on quality and installation

Neither is a promise; each is a typical range. The Less wording holds the clue that matters, which is quality and installation. A good product badly laid will fail early at its laps and details. A modest product carefully laid, on a deck with a proper fall and clear outlets, can reach the upper end.

The weak points on a felt roof sit in a few places: the laps, the upstand at the wall, the junction with a gutter, and any spot where water stands. A blistered cap sheet or a split at a seam is a sign of ageing, and it may or may not be beyond repair. Blisters that are small, dry and unbroken are judged differently from blisters that have burst and let water into the layers beneath.

Compare the felt figure with the others. HomeBuilding gives EPDM 25-30 years and GRP 25-30 years, with Less at 30 to 50 and 25 to 40. Felt lasts the shortest time of the three in both sources. Our guide to how long torch-on felt lasts looks at the ageing signs one by one.

Where felt still earns its place

Felt is not out of date. For some roofs it remains a sensible match, and a roofer who proposes it for the right roof is giving good advice.

  • Small, simple roofs such as sheds, porches, outbuildings and garages, where a cheaper covering with a shorter life is a reasonable trade.
  • Roofs with awkward shapes, because layered sheets can be cut and shaped around details.
  • Roofs with many penetrations, where a hand-formed detail is easier than a prefabricated one.
  • A short-life solution on a building that is due for alteration, where a covering built to last fifty years would be wasted.

The price is part of the case. For cost, Which? (November 2025 survey, excluding VAT) gives £1,400-£3,500 for a felt flat roof on a typical single garage measuring 6 m by 3 m. MyJobQuote gives £80 to £120 per m² for felt flat roofs, installed. Those are two different kinds of figure, one a total for a garage and one a rate per square metre, and neither can be turned into a quote for your roof. The per m² rate is never to be multiplied by an area.

Other coverings suit other jobs, and a roofer should be willing to say so. Where the roof is to be walked on, or where the longest life is wanted, we would also describe rubber or fibreglass. Each of those has its own guide in this section of the site.

When felt is the wrong answer

A fair account of felt includes the cases where we would steer you away from it, and there are four.

Standing water is the clearest case, and it is the one we meet most clearly in the survey photographs. A felt roof that ponds ages faster in the wet zone, and laps that sit under water can open. If the fall is wrong, felt over the top will inherit the problem. Our guide to ponding water on a flat roof explains how to tell a fall problem from a covering problem.

Other cases

The second case is a roof with a history of repairs. Patch upon patch builds up ridges and dams that hold water, and each patch is a join that can fail. When the covering has been mended many times, a fresh start with the deck corrected can be better than another layer on top.

The third is heavy foot traffic. A felt cap sheet with granules can be scuffed through by regular walking, and a roof terrace needs a different build-up with a proper walking surface.

The last is a case where the owner wants the longest possible life with little upkeep, which is a fair wish. Felt has the shortest range of the figures above, and a longer-lived covering will cost more at the start. Which option is the better buy depends on how long you expect to keep the house, and we lay out both sides at the survey so that the choice rests with you, informed by the photographs. The same reasoning applies to a roof on a rented property or a building about to be sold.

Replacing felt: the insulation rules in England and Wales

Stripping off failed felt and laying a new membrane counts as renovation of a flat roof, and the numbers are not the same in both countries.

In England, the 2021 edition of Approved Document L counts a new waterproof layer laid on a flat roof as one of its renovation examples. Table 4.3 there lists 0.35 W/m²K as the roof threshold and 0.16 as the improved value, and paragraph 4.13 offers a relaxation based on a 15-year payback. The Planning Portal's test for needing no application is "Less than 25 per cent of the total 'building envelope'" together with "Less than 50 per cent of the roof", so a full re-cover does need to go to building control.

In Wales, the Welsh Government says re-roofing in most situations needs Building Regulations approval. Welsh Approved Document L, in Table 11.1, gives 0.16, not worse than 0.35 where 0.16 cannot be reached, and its paragraph 11.16 counts a flat roof's waterproof membrane among the layers whose replacement is caught.

The practical effect on a felt job is that insulation comes into the specification, and the roof edge, the door threshold and the upstands may all need to rise to take it. Our guide to replacing a flat roof and the insulation rules sets out the full picture, and the building control body, either the council or a registered building control approver, is asked before work starts.

Felt roofing: your questions

Is torch-on felt the same as the felt on an old shed roof?

No. Modern torch-on felt is a bitumen sheet with a reinforcing core, laid in layers and bonded by heat or adhesive. Shed felt is a lighter product nailed down in one layer. They share a name and a material family but belong to different grades of work.

Can I walk on a felt flat roof to clear the gutters?

Only with care. The granule surface on a cap sheet can wear through under regular foot traffic, and a crack from a boot heel is a path for water. If the roof needs access for maintenance, plan a route and ask us to fit a protected walkway during the job.

Does felt always need to be replaced all at once?

No. Where the layers are sound and the trouble is one local split, lifted lap or failed flashing, a repair can be the better buy. We photograph the area and tell you which is which. Where the cap sheet is failing across the roof, a full re-cover becomes the honest answer.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing