In brief
MyJobQuote's page dated 20/10/26 says an installed felt flat roof comes to between £80 and £120 per m². That is a typical UK rate, with no Hereford figure behind it and no statement of VAT, and it is not our price. Area is only one thing that sets the cost of a roof. Access, the deck, insulation and the edge details change it, which is why the price comes after a survey.
The published rate and what it is a rate of
Felt in this context means torch-on felt: bitumen-based sheets bonded to the roof with a flame, normally in more than one layer. MyJobQuote gives the installed rate in its guide to flat roof construction, dated 20/10/26, as between £80 and £120 per m². Installed means the covering has been laid, not just supplied.
Four limits come with a rate like that:
- it is a UK-wide figure, and none of these guides is specific to Hereford or the border counties
- it describes a typical felt roof, not one with unusual edges, outlets or a deck needing repair
- it is a unit price, and a unit price is not a total
- it is what a guide says roofers charge, not what any one firm will quote, so two firms can sit either side of it for good reasons
It stays a rate here and is never worked up into a sum for your roof, because the area, the deck and the access come first. Whether a rate suits a given roof is a question for the survey. The torch-on felt roofs today page describes the layers and how they are bonded.
How long felt lasts is half the question
A rate per m² does not say how many years it buys. The two published guides disagree on felt, so both are given here, each with its own wording and date:
| Source | Felt |
|---|---|
| HomeBuilding | 10 to 15 years |
| Less (updated 27 October 2026) | 10 to 20 years, with the top of the range tied to materials and workmanship |
Neither figure is a promise; each is a spread. Less ties the top of its range to the materials and the installation, which are the points a survey weighs: how sound the deck is, how the edges are finished and where the water drains to. A felt roof near the lower end of either range is worth a look sooner than one in the middle.
A cheaper rate can be the dearer choice over time, and a higher rate is no proof of a better roof. The only way to compare is the full written description of what is being laid, set beside the years each guide gives. The page on how long torch-on felt lasts covers the reasons the range is so wide.
What moves a felt roof's price off the rate
Two roofs of the same area can cost different amounts. A survey records these before a total is written:
- the state of the deck, since soft or stained boards are renewed before felt goes on
- whether there is insulation, and whether it is being added or replaced
- the number of upstands, corners and outlets, each of which is detail work
- the edge finish, and whether new trims and drips are needed
- the access to the roof, and whether scaffold has to go up
- what is already on the roof and has to be taken off and carried away
Laid side by side, quotes should each say whether VAT is added and whether scaffold is in the total. A rate given without that detail cannot be set against one that has it, and a low figure that leaves scaffold out can finish above a higher one that includes it.
Our figure is one written total for your roof, given after the survey and based on the photographs taken. For a small garage roof the same published guides give whole-roof ranges, covered on the page about what a felt garage roof costs.
Rules that apply when a felt roof is replaced
A re-cover is not only a price question. For England, the Planning Portal's test treats a re-cover as normally needing no application while under 25 per cent of the building envelope and under 50 per cent of the roof is involved, and extra weight, set at 15 per cent or more, counted as a separate trigger. In England, Approved Document L counts replacing a flat roof's waterproofing as renovation, which can bring in the insulation: its Table 4.3 sets a 0.35 threshold and an improved 0.16 W/m²K, and allows a lower standard where a 15-year payback cannot be met.
For Wales, the Welsh Government's guidance is that re-roofing in most situations needs Building Regulations approval. For a flat roof with insulation built in, that guidance adds that the thermal element may need upgrading, while some repairs need no application at all. The Welsh Approved Document L, Table 11.1, sets 0.16 W/m²K and treats 0.35 as the worst acceptable figure where 0.16 is out of reach.
On either side of the border we confirm the position with the council's building control service or a registered building control approver, and only then set a date. The flat roofing hub explains the other coverings.
