In brief
A blister is a bubble between the layers of a felt roof, or between the felt and the deck. Air or moisture trapped there expands as the surface heats, so a bubble that was flat in spring can stand proud in summer. A small intact blister is a warning to watch. One that has split lets water in, and a spread of them can mean the covering has aged out.
What a blister is, and the three states we see
Felt is built up from layers of bitumen sheet. A blister forms where those layers have lost their bond to each other or to the deck, leaving a pocket that fills with air or damp. Felt laid in a hurry over a deck that was not quite dry is one way it begins, and a deck that has been soaked by an earlier leak is another. Whatever is inside it, air or moisture, is squeezed when the surface warms and pushes the felt up.
| State | What it looks like | What we do |
|---|---|---|
| Intact and small | A smooth dome, firm under a gloved hand | Photograph, mark and watch |
| Split | A crack or tear on the crown of the dome | Cut out and make good, then test the area |
| Wet beneath | Soft, with moisture when opened or a stain on the ceiling | Dry or replace the layers and check the deck |
The first state can sit without harm for some time. The second and third are leaks, or the start of one, and they call for a visit sooner.
Why warm weather brings them out
Heat is the trigger and a pocket is the cause. Dark bitumen takes up sunshine and the surface of a flat roof gets much hotter than the air around it. Anything trapped below that surface warms and expands, and a weakly bonded patch of felt gives way first.
What was trapped in the first place varies. Possibilities we look for on a survey include:
- moisture in the deck or insulation when the felt was laid, perhaps after rain
- air caught between layers during laying
- damp that has risen from inside the building as vapour and collected under a covering that cannot let it out
- a leak elsewhere that has soaked the deck and now evaporates from below
The last two matter because the cure is not only on the surface. Our page on condensation under a flat roof explains how moisture gets under a covering from inside. A felt roof also ages, and HomeBuilding gives felt 10-15 years against Less's 10 to 20, so a covering in its later years is more likely to have lost bond across its surface.
What to do about a blister
First, resist pressing or walking on it until someone has examined it. Walking on a blister can burst it, and pricking one to let the pressure out opens a hole in the covering. The second is to note where it is and take a photograph in the same light each week, so you can see whether it is growing.
When we survey, the sequence is straightforward:
- Press each blister to judge whether it is dry or wet.
- Check the ceiling below for stains, and the deck at the nearest edge for dampness.
- Cut open any suspect blister where that is warranted, and look at what is inside.
- Photograph the findings together with the edges, laps and outlets.
One small dry blister may be left to be watched. A split one is cut out and patched. A wet deck is dried or replaced before new felt goes on. For orientation, MyJobQuote's flat roof page, updated on 20 October 2026, quotes £80 to £120 per m² for installed felt. That is a rate for new felt and not a price for a repair, so a figure for your roof has to wait for the survey, and it then comes in writing as one total.
Repair or renew, and the border rules
A few blisters on a young roof point to a repair. A spread of them across an old covering, with splits at the laps, points to renewing it, and our report puts a photograph beside each finding. For the lifespan question, see how long torch-on felt lasts.
Renewing the covering counts as renovation. In England, a new flat-roof waterproof layer sits among the renovation examples in Approved Document L (2021 edition), whose Table 4.3 gives 0.35 and 0.16. The Planning Portal's own test is less than 25 per cent of the building envelope and less than 50 per cent of the roof. In Wales, the Welsh Government's starting point for re-roofing is approval in most situations, and in the Welsh Approved Document L, Table 11.1 gives 0.16 with 0.35 as the worst acceptable figure.
If the cause is moisture rising from inside, a new covering alone will not cure it, so we raise the insulation and ventilation with building control, meaning the council's service or a registered building control approver, before pricing. The flat roofing hub sets out the other flat roof guides.
