01432 610152 Get a quote Call 01432 610152

Large-roof leaks

Finding leaks on large commercial roofs

On a large roof the drip and the hole can be many metres apart. This guide shows how we trace one, from the building's history to a water test, in England and Wales.

Horizon Roofing Hereford 9 min read

A leak in a house roof can be close to the stain. On an industrial unit, a warehouse, a barn conversion or a row of shops, the roof can run to hundreds of square metres, and water entering at one point may run a good distance before it appears. It runs along the ribs of a metal sheet, follows a joint in a membrane, soaks into insulation and drips from a purlin, a light fitting or a stored pallet far from where it started.

That is why a quick glance may not find the fault, and why patching the spot that looks wet can fail. A better route is to treat the leak as a set of clues: what the building has recorded, what can be seen from inside, what the roof shows when we reach it, and, where those do not agree, a test that proves the answer.

This guide follows that order. It also covers the safety points that come first on a large roof, and what differs between England and Wales when a leak repair turns into a new covering. The full range of work on business roofs sits on our commercial roofing page.

Why a large roof hides where the water gets in

Water on a roof follows the surface it lands on. On profiled metal, it runs down the troughs of the sheet and sideways along a lap. On a flat membrane, it runs towards the lowest point, and a join or a puncture in the membrane lets it in wherever the roof happens to be wet. Below the covering, it meets insulation and a liner, and these can carry it a long way before it drops.

So the stain on the floor or ceiling tells you where the water came out, not where it went in. Three habits of large roofs make the gap wider:

  • the fall of the roof carries water toward the eaves, a valley or an internal gutter, and any gap along that route can leak
  • insulation soaks up water and passes it on slowly, so a drip can continue after the rain has stopped
  • a roof of many bays has many laps, rooflights and joints, each of them a candidate

Not every drip is a leak. Warm, damp air from the building can condense on the cold underside of a metal sheet and fall as drops on dry days. Our answer on why a metal roof drips inside explains how to tell the two apart. A leak that follows rain is a leak; a drip that follows cold mornings and cold nights is more likely to be condensation.

Begin with the building's own history

The easiest clue to gather is a good record. Before anyone goes up, we ask what the building can tell us, because the answers narrow the search from a whole roof to a few bays.

Useful information includes:

  • the dates and weather of each drip, and which way the wind was blowing
  • photographs of the stains, taken with something in shot for scale
  • earlier repairs, and whether a patch has been made at the same spot before
  • drawings or a plan, showing the position of rooflights, gutters, outlets and plant
  • any roof inspection or maintenance report, and the date of the last gutter clear-out

A leak that appears only in a gale from one quarter points to an exposed edge on that side. A leak that comes with any rain at all points to a gap in the covering itself. A leak that follows melting snow can mean water backing up behind an outlet or a blocked gutter.

Please do not climb up to look, however tempting it is. Large roofs carry the risks of fragile rooflights and edges with no protection, and a quick look from the roof edge is how falls happen.

If you have a floor plan, mark the stains on it and send us the picture. We will line it up with the roof layout before the visit, and we will ask who can let us into each part of the building, since a roof over several tenants has several keyholders.

Working from inside the building

A tour of the inside gives the first map of the problem. We go over the floor below the roof carrying a torch and a camera, and, where there is a ceiling void or a roof space, we look into that as well.

Clues inside the building and what they suggest
Inside the buildingWhere the water may be entering
Stains in a line across several baysA lap, a ridge or a joint that runs the same way
Wet insulation above one spotA cut, a fixing or a split in the covering above it
Drips around a rooflightThe rooflight kerb, the sheet around it or its seal
Water along the wall lineAn abutment, a parapet or a box gutter
Rust marks and daylight through the roofA corroded sheet, fixing or edge

We work uphill from the stain, in the same way as in a house, but across a larger plan: from the wet spot, along the rib or the purlin, towards the higher side of the building. We mark each finding on the plan with a number and take a photograph of it, so that the roof visit can start at the most likely places.

If the leak runs through electrics or stock, we advise protecting or moving them first. Water and a live fitting are a danger in their own right, and the building's electrician is the person to isolate a circuit.

On the roof: laps, rooflights, outlets and falls

With the inside mapped, the roof visit has a short list to check, and it starts at the highest point and works down. On a metal roof we go through the laps, the ridge, the rooflights, the fixings and the flashings around plant. On a membrane roof we look at the joins, the upstands, which are the short walls a membrane is lapped up against, the outlets and any place where the surface holds water.

Standing water is itself a clue. For flexible membranes, NFRC says BS 6229:2025 sets "a minimum 1:80 finished fall for general roof areas and internal gutters", and IKO advises designing for a fall of 1:40 to achieve it. A pond that remains well after rain means the fall has been lost, whether through sagging, a blocked outlet or an error at the build. You can read NFRC's note on the 2025 update to BS 6229.

Gutters matter just as much. Brett Martin gives a fall of "1mm for every 600mm" for rainwater gutters, and a gutter that sags or has a blocked outlet will overflow into the wall or back under the covering. Box gutters, the lined channels between roofs, and valleys are covered in our guide to valley and box gutters on commercial roofs. Our answer on what fall a commercial flat roof needs adds detail on falls.

Where plant sits on the roof, such as a fan, a flue or a solar frame, we check the fixings and the seals around each base, because every penetration is a place where the covering has been cut or lifted.

Testing when the clues do not agree

Sometimes the inside and the outside point to different spots, or the roof shows three suspects and no culprit. Then we test, and the test is a slow one, because the point is to change one thing at a time.

A water test goes like this:

  1. Choose the area the inside clues point to and isolate it from the rest of the roof.
  2. Start at the lowest part of that area and wet it gently with a hose, never a jet.
  3. Have someone watch the inside for drips and note the time.
  4. If nothing shows, move uphill to the next band and repeat.
  5. When a drip starts, the last band that was wetted holds the entry point.

The order matters: wetting a high point first can send water down to a low gap and give a false answer. Ordinary garden-hose pressure is plenty, and a jet is not needed.

Photographs from a drone can also help on a large roof, where the area is hard to see from one place. MyJobQuote states that the pilot needs an Operator ID and also a Flyer ID, both issued by the CAA, once the camera weighs 100g or more, which is its own summary and not the CAA's. A drone shows the roof from above. It does not replace walking the inside or testing a suspect area, and the results from the air still need a person on the roof to confirm them.

Keep the people below informed while a test is running. Someone has to watch the inside, and a shared radio or phone line between the roof and the floor keeps the timing exact.

Once the entry point is found, we photograph it, explain the repair and quote one total price in writing.

Safe access, asbestos and the rules by country

On a large roof, safety comes before diagnosis. Rooflight sheets and corroded metal can give way, and the HSE calls asbestos cement roofs "always fragile". Under the HSE's rule, any building put up or refurbished before 2000 is presumed to contain asbestos, so an older unit is handled on that basis until a test shows otherwise. CDM 2015 regulation 15(5) calls for a construction phase plan on a single-contractor project, and the plan records who goes where and with what protection.

If the leak turns out to need larger work, the rules depend on the country:

  • In Wales, the Welsh Government's page on re-roofing opens with "In most situations, this work will need Building Regulations approval."
  • In England, the Planning Portal gives an envelope test that was written for houses, so for a unit we ask the council's building control or a registered building control approver before re-covering.
  • In England and in Wales, bats are licensed by Natural England and Natural Resources Wales respectively, and a nest is protected while it is in use or being built.

Where a platform or scaffold stands over the road, a licence under section 169 of the Highways Act 1980 is needed, and we arrange the licence with our scaffolder.

What a repair costs on a roof this size depends on the survey findings. When it comes, our quote is a single written total covering access equipment, taking the waste away and leaving the site clean.

Large-roof leaks: your questions

Why does my warehouse drip in one bay when the hole is somewhere else?

Water travels along sheet ribs, liners and insulation before it falls, so the drip marks where it came out and not where it got in. We follow the trail uphill from the stain on the plan, then check that part of the roof and, if needed, run a water test.

Is a drone survey enough to find a leak on a big roof?

A drone helps with a wide view of laps, rooflights and ponding, and it keeps people off fragile sheets. It cannot show what is happening under the covering, so we pair it with a tour inside the building and, where the clues disagree, a water test.

Can I patch a leak on my unit's roof myself?

We would ask you not to go up. Rooflights and old sheets can be fragile, edges can be unprotected, and an older roof may contain asbestos. Photograph the stains inside, note when they appear and send them to us, and we will arrange access safely.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing