In brief
For a flat roof with a continuous flexible membrane, BS 6229:2025 sets "a minimum 1:80 finished fall for general roof areas and internal gutters", according to the NFRC. That is 12.5 mm of drop for every metre of run. IKO advises designing for 1:40 so that 1:80 is still met once the roof is built. It is a British Standard, so one figure serves England and Wales.
What a fall is and how 1:80 reads
Fall is the gradient given to a deck so that water runs off it to the drainage points. It is written as a ratio: 1:80 means a drop of one unit over eighty units of run. Over one metre that is 12.5 mm, and over a 10 m span it is 125 mm. It is a gentle slope, yet on a large commercial roof it separates a roof that sheds water from one that holds it.
The 2025 edition of BS 6229 governs level and gently curved roofs (no steeper than 10 degrees) whose covering is a continuously supported flexible waterproof layer. That takes in membranes such as felt, EPDM and single-ply. The 2018 edition was withdrawn on 16 December 2025. The standard does not cover lead.
The NFRC puts the new minimum as "a minimum 1:80 finished fall for general roof areas and internal gutters". The word that matters is finished, and the next section explains why.
A roof in Powys is judged against the same standard as one in Shropshire. Where a council or a registered building control approver is involved in a re-cover, the fall is one of the things a specification should state.
Why a roof is designed for 1:40
A roof is never laid perfectly. Decks deflect, insulation boards settle, and laps and upstands add small humps. The fall that counts is the one left after all of that, the finished fall. IKO, a membrane maker, explains that to reach a 1:80 fall the code of practice has the roof designed for a fall of 1:40.
| Fall | Per metre of run | Role |
|---|---|---|
| 1:80 | 12.5 mm | Minimum finished fall (NFRC) |
| 1:40 | 25 mm | Fall to design for (IKO advises) |
A flat roof with no fall built into the deck is therefore a risk to be priced in, not a detail to be smoothed over later. A roof built dead level can hold water in every low spot, and no repair to the membrane changes the shape of the deck beneath it. Raising the fall is a job for the build-up under the covering, such as tapered insulation, which is why the specification and the survey have to agree. If the survey finds a roof already holding water, the options are priced against that finding, not against an assumed fall.
Gutters, outlets and a different sum
The standard's figure covers general roof areas and internal gutters, the channels inside the line of the roof where water runs to an outlet. A box gutter between two roof slopes is one example, and it matters on commercial buildings because a failed one can drip into the building. Brett Martin, a gutter maker, gives "1mm for every 600mm" as the fall for a gutter, a much gentler slope than the 1:80 used for membranes, so the two rules are not interchangeable.
Roofs that do not use a membrane follow their own maker's data sheet. Marley's minimum pitch table, for example, lists a different pitch for each product, and the advice is to check the data sheet every time. The same is true of profiled metal sheets, whose laps and fixings are covered in profiled metal roof sheets.
Box gutters are looked at on their own in valley and box gutters on commercial roofs, because a few millimetres of lost fall in a long channel can leave it standing full after every shower.
Checking the fall on an existing roof
On a survey the first sign to look for is standing water. We look for shiny patches, tide marks left where puddles dried, and algae or debris gathered in one spot. Photographs of each go into the report.
The survey can show whether the roof drains, where it holds water and whether the cause is the deck, the insulation or an outlet. Setting a level along a length of the roof and measuring the drop turns that into a fall figure. Three things then decide the remedy.
- where the water collects
- how far that spot sits from its outlet
- whether a new covering can be laid to improve the slope, for example over tapered insulation boards
If the roof drains and is merely worn, repair is the better buy, and that is what you are told. If the fall is the fault, re-covering without correcting it only repeats the problem. How the covering is chosen is covered in is felt still used on commercial roofs.
Fall is one of the topics under commercial roofing, and the price you receive in writing is one sum, set once the survey has shown the roof's condition and how water leaves it.
