01432 610152 Get a quote Call 01432 610152

Felt on business roofs

Is felt still used on commercial roofs?

Yes, felt is still laid as a flat roof covering, and BS 6229:2025 covers it. Its quoted lifespan is shorter than the single-ply alternatives.

In brief

Yes. Torch-on felt is still a flat roof covering, and BS 6229:2025 deals with continuously supported flexible membranes. The lifespans quoted are shorter than for single-ply: HomeBuilding gives felt 10 to 15 years, and Less says torch-on felt lasts 10 to 20 years depending on quality and installation. Whether it suits a commercial roof turns on the deck, the fall, foot traffic and how long you need the covering to last.

Where felt still fits

Felt is bitumen-based roofing laid in layers over a flat deck. Torch-on felt is the version whose underside is heated with a gas torch so that it bonds to the layer below. It is a continuously supported flexible membrane, the group of coverings that BS 6229:2025 deals with, so the minimum 1:80 finished fall in the standard applies to it exactly as it applies to single-ply.

Felt still appears in the cost guides among the flat roof coverings, and it is still specified where a short-lived, simple covering suits the job. Which? and MyJobQuote both give felt prices for domestic flat roofs, but those are house-scale figures, and a commercial roof is a different case in size, access and edge detail.

So a commercial felt roof is priced once the survey has taken in the deck, the drainage and the access. The price comes to you written down, as a single sum, not as a rate per square metre, because a rate hides everything that makes one large roof different from the next.

How felt compares with the alternatives

Lifespans quoted for flat roof coverings
CoveringHomeBuildingLess
Felt (torch-on)10 to 15 years10 to 20 years
EPDM25 to 30 years30 to 50 years
GRP25 to 30 years25 to 40 years
Lead60 to 100 years50 to 100 years

These are ranges as published, and the two sources do not agree, which is why both are shown. A longer life can come with a higher first cost, so the real choice is between paying once and paying again sooner.

The other coverings in the table are easy to place. EPDM is a synthetic rubber sheet supplied in large pieces, so there are few joints to fail. GRP is glass-reinforced plastic laid wet and left to cure in place, which gives a joint-free surface once it has set. Lead is sheet metal, long-lived and heavy. Which of these suits a particular roof depends on its shape, its use and its structure, and the survey sets that out in a form you can compare.

Single-ply membranes, the rubber and plastic sheets that are welded or bonded in one piece, are covered in single-ply roofs on commercial buildings, and TPO, one kind of single-ply, is explained in what is a TPO membrane.

When felt is the right call

Felt suits a roof that is simple in shape, has a sound deck and needs a covering that does the job for a defined time. It also suits a repair where only part of an older felt roof is failing. You are told when felt is the better buy, and equally when it is not.

Felt loses its case on a complex roof with many penetrations, on a roof that sees regular foot traffic from plant maintenance, and wherever the owner wants the covering to outlast the lease. A longer-lived covering, or a repair that leaves the felt alone, is then worth pricing against it.

On the survey we check and photograph:

  • the deck beneath, for movement and rot
  • the fall, against the 1:80 minimum
  • laps, upstands and the edge trims
  • any asbestos cement sheets or boards under or beside the felt

For a unit built or refurbished before 2000, HSE says to assume asbestos is present, so that question is put to you before any felt is torn off, and the answer shapes how the old layers leave the roof.

Building control and weight limits across the border

Re-covering a commercial flat roof can need Building Regulations approval, and the route offers the same two choices either side of the line between England and Wales. In England, you ask the council's building control service or a registered building control approver. In Wales, you ask the council's building control service or a registered building control approver too. The Part L figures quoted for houses are written for dwellings, and a commercial building is a different case, so ask building control which document applies before the specification is fixed.

Weight is a separate test. In England, the Planning Portal ties approval to a new covering that adds 15 per cent or more to the weight of the roof. In Wales, Approved Document A puts the line at more than 15%. A change from one covering to another is checked against that limit, so the specification names the weight of what goes on. Felt is a thin covering, but the old layers, the insulation and any ballast above them all change the total, and the survey notes what is there before the weights are compared.

Everything here sits under our commercial roofing pages.

Related questions

How long does a torch-on felt roof last?

HomeBuilding gives felt 10 to 15 years. Less says torch-on felt lasts 10 to 20 years depending on quality and installation. Neither should be read as a fixed term, and a roof that drains badly or sees foot traffic can fall short of the lower end. A survey shows where yours stands, and the photographs let you see why.

Is felt the cheaper covering on a commercial roof?

Felt's shorter quoted life means a second covering sooner, so the first price alone does not settle it. Domestic cost guides cannot be scaled up to a commercial roof, which is why the options are priced side by side once the survey is done, in one written total each.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing