Profiled metal roof sheets are steel or aluminium panels pressed into a repeating wave or box shape, so that a thin sheet can span the gap between purlins (the horizontal beams that carry the roof). They cover factories, warehouses, workshops, farm buildings and many shops, and they come in a handful of forms that look alike from the ground but behave differently on the roof.
The three questions that decide how a sheet roof lasts are which type it is, how the sheets lap, and how they are fixed. A single-skin sheet with sealed laps and sound fixings can run for many years; the same sheet with an open lap and a rusted fastener lets water into the building within one wet spell. Knowing which parts matter makes a survey easier to read and a quote easier to compare.
The sections below cover the main types, the materials and coatings, the side and end laps, the fixings, movement and cut edges, and the rules in England and in Wales when sheets are replaced. The wider service is described under commercial roofing.
Three kinds of profiled metal roof
From the ground, most sheet roofs look similar. On the roof and from inside, they divide into three kinds, and the kind decides what can be repaired and how.
| Type | Build-up | Typical use |
|---|---|---|
| Single skin | One sheet, no insulation | Stores, barns, workshops |
| Built-up (double skin) | Liner, spacers, insulation, outer sheet | Heated units, offices |
| Insulated panel | Two skins bonded to a foam core | Cold stores, clean rooms |
A single-skin roof is the simplest. The sheet is the whole weatherproof layer and there is nothing beneath it, so a leak shows straight away and a repair can be a matter of the laps and fixings.
A built-up roof has a liner sheet on the underside, spacers (zed or bracket sections) fixed to it, insulation laid between them and an outer sheet fixed through to the spacers. The outer sheet can be replaced or overclad without touching the liner, but a leak may show at a point well away from the hole in the outer sheet because water runs along the insulation.
An insulated panel is factory-made, with the core bonded between two skins. Panels are lifted in as single units, so repair means resealing joints or replacing a whole panel. Which kind you have decides how a leak is traced and which parts can be reached. A roof section or a photograph of a cut edge settles the question without anyone lifting a sheet.
Profiles, materials and coatings
The profile is the shape of the wave. Corrugated sheets have a rounded, repeating curve. Trapezoidal sheets, also called box profile, have flat crowns and valleys with sloped sides, which gives them more strength across a span and suits them to newer units. A deeper profile spans further between purlins; a shallower one needs closer supports.
Sheets are made from steel or aluminium, and the coating decides how they age. The usual coatings:
- galvanised steel, a zinc coat on bare steel
- galvanised steel with a pre-painted polyester or PVC plastisol finish on top
- aluminium, which does not rust, though it dents more easily
Older sheets may carry a bitumen or paint layer applied on site rather than at the factory. A coating that has worn through on the crowns, where rain strikes first and the sun is hottest, is the first sign of trouble. Once the zinc has gone, rust begins, and a survey picks it up as orange staining along the crowns and at the cut edges.
The maker's data sheet for a profile gives its span, its thickness and the minimum roof pitch it will work at. That last figure varies by profile and lap, so it should always be read from the data sheet for the sheet in question, and the pitch of the existing roof checked against it before new sheets are ordered.
Sheets of this kind are also what an older asbestos cement corrugated roof can be replaced with, which is why the building's date matters at survey.
Side laps and end laps
A sheet roof is a series of overlaps, and every overlap is a place where water can get in. There are two kinds.
The side lap is where one sheet sits against the next, running up the slope. The edge of one sheet rides over the edge of its neighbour, by a corrugation or a rib. On a shallow roof or in a windy spot, a bead of sealant is run between the two and the laps are stitched together with small fasteners at intervals to hold them tight.
The end lap is where one sheet finishes and the next begins, further down the slope. The upper sheet must overlap the lower, and the shallower the pitch, the longer that overlap needs to be. Sealant between the sheets at an end lap is standard practice and the point at which some old roofs fail, because the sealant dries and splits long before the sheet wears out.
What to look for at a lap:
- daylight or staining through the overlap
- sealant that has cracked, peeled or gone hard
- stitching fasteners that are loose or missing
- a lap that has opened because the sheet has moved or bent
- rust bleeding from the underside of the lap
A lap fault can be a cheaper repair than a sheet fault. Resealing and re-stitching can restore a roof that would otherwise be written off, and a survey also looks for the other causes of a drip, such as condensation on the underside of the sheets.
Fixings: what holds the sheets down
The fixings are the part of a sheet roof that people overlook, and they deserve a close look. Sheets are fixed to purlins with self-drilling or self-tapping screws, each with a sealing washer under the head. The washer, for example a rubber ring bonded to a metal cup, is what keeps water out of the hole. When the rubber perishes or the screw backs out, the hole becomes a leak.
Where the screw goes also matters. A fixing through the crown of the profile (the high part) keeps water away from the hole but is more exposed to wind uplift. A fixing through the valley (the low part) holds the sheet more firmly to the purlin but sits in the path of any water running down the roof. The maker's instructions say which applies to each profile, and a mix of both on one roof can mean earlier repairs went in by guesswork.
At a survey, the common findings are:
- fasteners with perished or flattened sealing washers
- screws that have corroded in the hole, or sit proud of the sheet
- heads pulled through the metal in strong wind
- holes drilled for earlier repairs and left unfilled
- fixings missing from the end of a lap or the edge of a bay
Fixings are cheap to replace but slow to find on a large roof, so a survey that photographs a sample and notes the pattern of failure saves repeat visits. Our guide to why roof sheet fixings rust explains the causes of the worst cases.
Movement, cut edges and trims
Metal expands in the sun and shrinks in the cold. A long sheet moves more than a short one, so fixing details allow for it. If the fixing holes are tight and rigid, the sheet works against its screws, wears the hole oversize and lets water in. Slotted or oversized holes in the sheet, matched with the right washers, give it room to move.
The cut edge is where the sheet was cut to length or to fit round an opening. The factory coating is lost at that edge, so the bare metal is exposed. On pre-painted steel, the cut edge can start to corrode under the paint and creep inwards, which is the cause of the brown streaks that run up from the bottom of old sheets. Our guide to cut-edge corrosion in metal sheets covers it in detail.
Trims, flashings and ridge pieces close the roof at its edges, and each is another overlap, with its own sealant and its own fixings. A gap at a ridge or at a verge trim can let in enough wind-driven wet to stain a wall inside, even when the field of the roof is sound.
For the written quote, the survey reports on three groups of details:
- the field of the roof: sheets, laps and fixings
- the edges: eaves, ridge, verges and gutters
- the openings: rooflights, vents, flues and plant bases
Each group is photographed, so that the quote matches what is on the roof.
Repair, overlay or replace: the rules in England and Wales
What counts as repair, and what counts as building work, depends on the scale of the job and which side of the border the unit stands on.
- In England, building control is the council's service or a registered building control approver, registered with the Building Safety Regulator since 6 April 2024. For a commercial roof, ask which of the two applies and whether the sheet work needs an application there.
- In Wales, the Welsh Government links re-covering to improved insulation, and says approval is needed when the new covering performs very differently in a fire.
Replacing a few damaged sheets like for like is repair. Re-sheeting a whole roof, adding insulation or changing to a different profile and weight is a larger matter. Weight matters too. Approved Document A, in England and in Wales alike, says a significant change in roof loading is when "the loading upon the roof is increased by more than 15%", and new sheets, spacers and insulation all count towards that.
If the roof is asbestos cement, the choice of what goes over or in place of it follows different rules, covered in our guide to overcladding an industrial roof. A cement sheet roof is fragile whatever the age, and the survey is planned around that fact.
Before an order goes in, we put the question to whichever building control body covers the unit. The written quote gives a single total, so repair and replacement can be weighed side by side.
