01432 610152 Get a quote Call 01432 610152

Roofers in Painscastle

Roof repairs and re-covers in Painscastle, where the Welsh rules decide what each job needs.

Painscastle lies 25.6 miles by road west of central Hereford, about 39 minutes' drive. Every survey ends with one written total price.

Get a free quoteCall 01432 610152

Painscastle roofs and the consents they bring

  • Older cottages with weathered clay tile roofs and brick chimneys behind a flint wall
    Brick stack, listed hall rangeUpper House has a projecting brick stack, so its lead and pointing come first.
  • Slate roofs and chimney stacks along a red brick Victorian terrace
    Plain bargeboards on a gableTimber boards at a gable edge soften where the paint and verge joint fail.
  • Newer homes with grey concrete tile roofs along a curving estate road
    Listed barn and farmhouseNewhouse Barn and Newhouse are Grade II, so consent is settled before work starts.

Where Painscastle lies

Painscastle on a street map, with a dashed circle around the town and the nearest towns we cover. Tiles © Esri; map data © Esri, HERE, Garmin, OpenStreetMap contributors.

A Painscastle roof, stack to slope

From the brick stack to the bargeboards: a Painscastle roof checked in order

A survey here follows one listed hall range outwards. It begins at the projecting stack and its lead, moves to the gable edge and its bargeboards, then covers the slopes, where Welsh rules decide when a re-cover needs approval.

A drawn cut-away section through a Herefordshire border house: the front of the main roof is cut open to show the rafters, underlay, battens and slates, beside a black-and-white timber-framed gable. Numbered, from the ridge down: 1 Brick stack; 2 Gable edge; 3 Slopes.

Fig. 1 A Painscastle house in section, with stack, gable edge and slope numbered.

Callout 1 of 3

The projecting brick stack on a listed hall range

Cadw's listing description of Upper House in Painscastle, which is Grade II* (Cadw record 9349, designated 3 August 1987), runs: "Two storeys, white-washed rubble walls (some repairs), slate roofs, projecting brick stack to hall range, plain bargeboards". Read as a survey order, that line starts with the stack. A stack that projects stands out from the wall it rises beside, so the seam where brick meets slate has to stay tight on every face of it.

Lead does the sealing. Think of a flashing as a lead strip tucked into the stack's joints and folded over the slates, a soaker as a folded lead square under each slate course beside the brick, and the back gutter as the lead channel behind the stack that diverts run-off sideways. We check all three for splits, lifted edges and lead that has slid down the slope. A failed run is cut out and replaced, because sealant smeared across a split hides the fault only until the next hard shower. Where an old run is sound we leave it, and the report says why, with a close photograph of the lead that is staying.

Then comes the brick. Pointing is the mortar line between courses. Flaunching is the sloping mortar crown round the pots that throws rain clear of them. Hollow-sounding brick, joints soft enough to mark with a fingernail and a visible lean all go in the report. The ground gives no view of a stack's four faces, so each one is photographed and you see every picture before we set a price.

A stack set in a wall that two houses share brings in the Party Wall etc. Act 1996: it is the owner who serves that notice, and it must go out at least 2 months before a chimney breast is cut away. Surveyors come into it later, and only when the adjoining owner objects or leaves the notice unanswered for 14 days. Agreeing the sequence with both households first spares everybody a long wait on site. A listed house adds a consent step as well, which the next callout explains. Our chimney repairs page deals with rebuilds and repointing.

Looked at on a projecting stack

  • Lead flashings split, lifted or slipped
  • Soakers at the side of the stack
  • Pointing between the brick courses
  • Flaunching and the pots above it
  • Any lean in the stack itself

Four faces, four photographs: that is how a stack gets read.

Fig. 2 Chimneys, drawn close

Callout 2 of 3

Plain bargeboards, the verge and listed building consent

The same listing records "plain bargeboards". A bargeboard is the timber board that finishes a gable edge and hides the rafter ends behind it. Where the covering stops beside it, the verge is sealed with bedded mortar or with a dry-fix verge unit held by screws and clips, a method BS 8612 covers. Either way the job is to keep rain from running in behind the board.

We feel along the lower end of every board for soft timber, check how each length is fixed, and look for paint that has crazed or lifted. Once the verge joint opens, rain gets behind the board and stays there, so a board that looks sound from below can be rotten at its back. Ladder or scaffold photographs show the board ends, and the report says whether a patch will serve or a whole length must come off. If the paint has failed but the timber is still hard, a clean and a repaint may be all the board needs, and the report will record that.

Painscastle has listed buildings besides Upper House. Newhouse Barn is Grade II (Cadw record 15904, designated 9 March 1995), and Newhouse is Grade II as well (record 15903). In Wales the Historic Environment (Wales) Act 2023 section 88(1) says: "A person must not carry out works to which this section applies, or cause such works to be carried out, unless the works are authorised under section 89." Section 89 is listed building consent. Listing leaves a house its permitted development rights for roofs, but consent sits alongside them. A bargeboard cut to a new profile, or a verge reworked in other materials, is the kind of change to settle with Powys County Council before the old board is unscrewed.

Conservation area boundaries are held on Powys County Council's own list, so look up your address there, and put the Article 4 question to the council too. Those answers decide how far a new roof window can go without planning permission, and our planning guide for roof windows sets out the Welsh position. For the protected houses themselves, see listed and heritage roofing.

A gable edge in Painscastle

SoundBoard tight, paint whole, verge bedded and square
Needs workSoft board end, open verge joint, fixings working loose

Callout 3 of 3

When a Painscastle re-cover needs Building Regulations approval

Re-covering a slope is the largest job on any roof, and in Wales the Welsh Government opens its guidance with a flat statement: "In most situations, this work will need Building Regulations approval." The same guidance adds a point about heat: "As a roof is defined as a thermal element, the work to re-cover a roof should also include for improving the thermal insulation properties of the roof." A new covering is therefore also a question about the loft or rafters beneath it.

The Welsh Government's roof page puts a marker on the area: where you are replacing or repairing "more than 25 per cent of the roof area", better insulation normally becomes part of the job. Smaller repairs and re-covers below that mark do not normally need an application. Before pricing a slope we measure it, so you know which side of the mark the work lands on, and the measurements go into the report. Under the Welsh Approved Document L, Table 11.1 asks for a renovated roof to reach 0.16 W/m²K, with 0.35 as the worst acceptable figure where 0.16 is not feasible. Renovating more than 50% of an element brings the whole element into scope (paragraph 11.14), and a 15-year payback decides what counts as feasible (paragraphs 11.20 to 11.21).

A change of covering is a weight question. The Welsh Government offers slate to tiles as its example, noting that a significantly heavier or lighter covering makes approval likely. Welsh Approved Document A calls a roof loading change significant once it rises by more than 15%. On planning, the Welsh Government says the appearance of new materials "must, as far as possible, match the appearance of those used on your existing roof". Slate for slate is the plain answer on a house like Upper House, whose listing records slate roofs.

From inside the loft we study the battens, the rafters and the underlay, and on the slope we lift sample slates, with the loft hatch open for daylight, before choosing between repair and re-cover. Where the existing covering can stay, the report says so. Where it cannot, the quote names the covering, fixings and underlay it assumes, as one total. For the whole sequence of a stripped slope, from first slate off to last capping on, read roof replacement.

On a Welsh address, we measure the slope before we name a price.

Recorded on a slope before pricing

Slate faces
Cracked, flaking or slipped units, shown in close photographs
Battens
Tested from the loft for soft or split timber
Underlay
Seen from inside for tears, sag and damp
Area
Measured, to place the job against the Welsh roof-area mark
Loft insulation
Noted, since a re-cover raises the Part L question

Painscastle roofs: listing, slate and consents

Can a few slipped slates on a Painscastle house be mended without re-roofing?

Yes, provided the battens and underlay beneath them are sound. We lift the courses round the gap, test the timber from the loft side, and send the findings with photographs. Which? gives £75 to £400 for replacing one to six tiles in its November 2025 survey, before VAT, though a slate roof or a hard slope can move a job outside that range. If the battens have failed, the report says a wider repair is the better buy.

Does a listed house like Upper House need consent to be re-slated?

Upper House is Grade II*, and in Wales sections 88 and 89 of the Historic Environment (Wales) Act 2023 govern works that affect a listed building's character. Replacing a tile with an identical match may leave little to debate, but a different slate size, colour or fixing is a change to agree first. Powys County Council is the body to ask, and we bring photographs of the existing covering to that conversation.

Where do I check a Painscastle address for conservation area status?

Powys County Council holds the conservation area list and can say whether an Article 4 direction applies to your address, so ask it directly. Do that before planning a new roof window, because the Welsh permitted development rules for roof lights tighten on conservation area land. Mending a roof as it stands is a smaller question, and we raise both at the survey so the order of events is clear.

Does a heavier roof covering need a structural check in Painscastle?

Welsh Approved Document A treats a change as significant when the loading rises by more than 15%, and slate to tiles is the Welsh Government's own example of a change likely to need approval. We inspect rafters, purlins and wall plates from the loft first. If the structure needs strengthening, that cost sits inside the written price beside the covering.

Will scaffold in Painscastle need a licence from the road?

Under Highways Act 1980 section 169, scaffolding that obstructs a road or footway is licensed, and we arrange the licence with our scaffolder. Our one written total takes in the scaffold itself, from the first standard to the last board taken down. Mention any narrow stretch or regular parking at the survey, and the platform can be planned around it.

Can new slate sit beside old slate on a Painscastle roof?

It can, if the new slates match the old in size, thickness and colour, and the repair keeps the lapping pattern. In SPAB's technical note, Welsh slate and stone roofs "are predominantly double-lapped", so a patch has to respect that pattern. It also advises that "Claims of unavailability or long delivery times should always be checked with the quarries", and that check comes ahead of any other material being proposed. HomeBuilding gives Welsh slate "100+ years" and reclaimed Welsh slate "50-80 years".

Book a stack-first survey in Painscastle

Outline the trouble with the roof, ideally with a picture; the stack gets checked first and one written total follows.

10-year workmanship guarantee, in writing