01432 610152 Get a quote Call 01432 610152

Roofers in Knowbury

Roof work in Knowbury, a Shropshire Hills village 25.3 road miles north of Hereford.

The Shropshire Hills National Landscape covers Knowbury, so we check the rules for your roof before any price is written.

Get a free quoteCall 01432 610152

Knowbury: a National Landscape and a listed vicarage

  • Older cottages with weathered clay tile roofs and brick chimneys behind a flint wall
    Shropshire Hills National LandscapeThe designation covers the village, which matters for any dormer plan here.
  • Slate roofs and chimney stacks along a red brick Victorian terrace
    Old Vicarage, Grade IIThe listing takes in the attached wall and gatepiers to the east.
  • Newer homes with grey concrete tile roofs along a curving estate road
    Dhustone and Hope BagotShropshire Council's conservation areas nearby are worth checking against your own address.

Knowbury near and far

Knowbury on a street map, with a dashed circle around the town and the nearest towns we cover. Tiles © Esri; map data © Esri, HERE, Garmin, OpenStreetMap contributors.

Gable edges, slopes and the Knowbury landscape

What the Shropshire Hills designation means for a Knowbury roof, from the verge down

Three callouts follow a Knowbury roof from its gable edges, through the slopes and the choice of covering, to the dormers that the National Landscape designation affects and the roof windows beside them.

A drawn cut-away section through a Herefordshire border house: the front of the main roof is cut open to show the rafters, underlay, battens and slates, beside a black-and-white timber-framed gable. Numbered, from the ridge down: 1 Gable edge; 2 Pitch and match; 3 Designation.

Fig. 1 A drawn house at Knowbury with the verge, the slope and the roof window each numbered.

Callout 1 of 3

Knowbury gable edges: verge units, bedding and fixings

The gable is the end wall of a house that runs up to the peak, and the verge is the covering that finishes its sloping top. A verge is the free edge of the slope, with no tile beyond it to hold it down, so it is the second thing our survey reads, straight after the ridge. We look along it from the ground and again from close up, for daylight under the units, for bedding that has crumbled, and for staining on the face of the gable wall below.

A verge can be finished two ways: units set in a mortar bed, or dry-fix caps and clips that hold the edge down. Marley points out that since the 2015 amendments to the tiling standard, mortar alone has not counted as an adequate fixing for a roof covering. The tiling standard, BS 5534:2014+A2:2018, and BS 8612 for dry-fix between them cover how a verge should be held down. Where we rebed a verge in mortar, a mechanical fixing goes in as well, so the fix does not rest on the bedding.

Behind the verge sits the barge board, or the exposed edge of the rafter on a house without one. We press the timber with a probe where it can be reached, because a board that has gone soft at the lower end tells us water has been running down the gable for some time. A verge can also lift because the rafter under it has twisted, which is why the survey follows the line of the edge as well as the units on it.

When one unit has gone, the repair is one unit and a fixing. When a run has loosened, it is bedded again from the nearest sound point. Photographs from before and after reach you with the report, so the finished edge can be compared with the one we found. Any waste from the old bedding is taken away, and the ground under the gable is left clear. Our pitched roofing page explains how verges, hips and ridges are finished on tiled and slated roofs, and what decides between a dry and a bedded edge.

An edge question

Why does a small verge repair deserve a proper look?

Because the edge carries the wind loading of the whole gable. One loose unit can be the first sign that the bedding has failed along the run, so we test the neighbours before calling it a single fix.

A Knowbury verge, part by part

Verge units
Rocking, cracked or missing, tested by hand
Bedding
Mortar present, sound and tight to the unit
Fixing
A mechanical fixing on every unit
Barge board
Timber firm, with no soft patches at the foot
Gable wall
Staining or damp below the edge

Daylight under a verge unit means the bedding has already failed.

Fig. 2 The verge, drawn close

Callout 2 of 3

Slopes, pitch and matching a Knowbury covering

Whether a slope can take a given covering depends first on its pitch, the angle it rises at. Marley's table sets a minimum for each product, so the roof is measured before a covering is suggested. Plain concrete tiles need 35°, a Double Roman in a smooth finish 22.5°, and the Edgemere 17.5°, while the Mendip, with its smooth finish, goes down to 15° and so does the Lincoln clay pantile. These are product names and not regional types, and each data sheet is checked.

For natural slate, Cupa says BS 5534:2014+A2:2018 "also indicates that the minimum roof pitch for natural slate is 20 degrees in the case of a project situated in an area with moderate exposure and with a slate 500mm long and a 115mm overlap". It adds that hook fixings are ruled out on any pitch below 25º. Every condition in that sentence has to hold, so we measure the slope, the slate length and the exposure before agreeing a specification.

Stone roofs bring a different difficulty. SPAB has a technical note on roofs in Wales and the Marches, and Shropshire is one of its counties. It warns that many original coverings were later swapped for another stone, for slate or for imitation stone slates, which is why we look hard at what is actually on the slope, course by course, before a repair is planned or a price is fixed. A stone slope is read from its own timbers and its existing angle, since the product tables above cover manufactured tiles only.

For supply problems, SPAB's advice is plain: if a supplier says stone is unavailable or late, put the question to the quarries themselves. We do that before suggesting a change of material for any Knowbury roof, and the answer goes in your report. A repair that keeps the existing covering is the better buy while the material can still be found. Replacement is offered when it cannot, or when the roof is worn through. Our roof replacement page explains how a new covering is chosen and laid.

Read on a Knowbury slope

  • Pitch measured against the product table
  • Length and overlap of each slate or tile
  • Whether the covering has been changed before
  • Availability checked with the supplier or quarry
  • Battens and fixings beneath the covering
Fig. 3 The slopes, drawn close

Callout 3 of 3

The National Landscape, roof windows and the Old Vicarage

Knowbury lies inside the Shropshire Hills National Landscape, the name now used for what used to be an AONB. It is a designation, and Shropshire Council makes the planning decisions, so the council is the body that answers a question about your house. We can describe the roof in detail for that conversation. For Knowbury roofs the designation matters chiefly when a dormer is planned, and our guide explains how a window set in the slope is treated by contrast. A dormer is therefore one to put to Shropshire Council, and our planning guide for roof windows sets out the rest.

Before any dormer is drawn, the loft is measured and photographed from inside, and the roof is photographed from outside, so the application rests on the building as it stands. Those notes can go to whoever draws the plans, and the council sees an accurate picture of the roof. If the rafters would need trimming for the opening, the survey records their size and spacing, and that detail goes to your designer or building control before the order is placed.

The fitting rules are separate again. AD L 2021 Table 4.2 puts windows, roof windows included, at 1.4 or WER Band B; the number for rooflights is 2.2. A loft conversion above 4.5 m follows AD B para 2.5, which offers a protected stairway or an alternative escape route. A skylight of the usual kind is an easier job than a dormer, and our Velux and skylight installation page covers it.

Among Knowbury's listed buildings is the Old Vicarage and Attached Wall and Gatepiers to East, Grade II (list entry 1383676, first listed 29 February 2000). Section 7 of the Planning (Listed Buildings and Conservation Areas) Act 1990 means consent is required for works that would change its character. Its permitted development rights remain, and consent has to be obtained in addition.

Shropshire Council's conservation areas near Knowbury include Dhustone and Hope Bagot. Check whether an Article 4 direction applies with Shropshire Council, since the council's page on its directions says they commonly control alterations to roofs and chimneys. For building control, call Shropshire Council Building Control on 01743 258710, or use a registered building control approver.

A roof opening in a National Landscape

SoundDesignation checked, planning answered, rafters trimmed and supported
Needs workDormer started on the assumption that no application is needed

Knowbury roofs: the designation, pitch and the Old Vicarage

Does Knowbury's place in the Shropshire Hills National Landscape change how a roof is repaired?

For repairs, the designation by itself adds no new permission, and Shropshire Council remains the planning authority for every application in the village. What changes is the choice of work: a dormer on this land goes to the council first, while a roof window meets its own conditions. We keep the covering and the look of the house in line with the original wherever the roof allows it, and say where it does not.

Can a dormer be added to a Knowbury house?

Yes, in principle, but put it to Shropshire Council's planning team first, which decides, because a National Landscape weighs on dormers and the plans are best settled before any builder is booked. A roof window carries its own conditions, listed in the guide, and a listed Knowbury house needs consent too. Our planning guide sets out the two positions, and the council can confirm either one for your address.

Which listed building stands nearest to the middle of Knowbury?

Old Vicarage and Attached Wall and Gatepiers to East, about 680 m out, is Grade II (list entry 1383676, first listed 29 February 2000). The listing covers the vicarage and its attached wall and gatepiers to the east. Work that would affect its character needs consent under section 7 of the 1990 Act, and Shropshire Council decides it, so ask the council before any change to the roof.

Which conservation areas lie close to Knowbury?

Shropshire Council's conservation areas near the village include Dhustone and Hope Bagot. Whether your own property stands inside either is for Shropshire Council to say. Ask the council too whether an Article 4 direction applies, because its page says directions commonly control alterations to roofs and chimneys, and it is better to learn that before any materials are ordered for the job.

What pitch does a natural slate roof at Knowbury need?

Cupa ties its 20 degrees to three conditions: moderate exposure, a slate 500mm long and a 115mm overlap, and it rules out hook fixings on any pitch below 25º. If your roof differs on any of those points, the figure changes, and a slope that looks steep enough from the road can still fall short once the slate length is known. We measure the slope and the slate before we specify, and the written price follows that survey.

How do the Planning Portal's percentages apply to a Knowbury re-roof?

Knowbury is in England, so the Planning Portal's test applies: re-covering that affects less than 25 per cent of the building envelope and less than 50 per cent of the roof normally sits outside the need for a building regulations application. Anything larger, or any covering adding 15 per cent or more to the weight, goes to building control, and Shropshire Council Building Control is on 01743 258710.

Ask about a verge-first survey in Knowbury

Tell us how your gable end looks from the ground, and we will check the roof from verge to ridge and quote in writing.

10-year workmanship guarantee, in writing