Foam sprayed under a roof is a bandage as well as insulation. It sets against tiles, battens and underlay, and while it stays put, nobody can see how those parts are doing. Slipped tiles may have been glued in place by the foam. A split batten may be held by it. A torn underlay may have been sealed in a tear.
When the foam comes off, the roof is seen properly for the first time since it was sprayed. Some of what appears is sound and needs nothing. Some needs a repair, and the repair has to suit the roof: its covering, its age, its fixings and the nation it stands in.
The sections below follow the repairs in the order we meet them, from tiles and slates, through battens and underlay, to the ridge, verges and flashings at the skyline, then the rules that apply if a repair grows and the typical costs published by others. For the whole foam removal job, see our spray foam removal page.
What the foam was hiding, and what it was holding
The first job once a slope is clear is to separate faults the foam hid from faults it was holding together. They look alike from the loft and need different answers.
A fault the foam hid is damage that was already there: a cracked tile, a slate that had slid, a torn patch in the underlay, a batten that had rotted. Taking the foam off does not cause it, and it is photographed so that this is on record.
A fault the foam held is a part that was only staying in place because the foam bonded to it: a loose tile held to its batten by a ridge of set foam, or a batten fixed by foam rather than nails. These come loose as the foam lifts, and we plan for them.
We sort what we find into four groups and photograph each before touching it. Photographing first matters, because once a tile is lifted its original position is gone:
- sound, and left alone
- loose, and re-fixed with new nails or clips
- damaged, and replaced to match
- unsafe to leave, and made good before the covering goes back
The groups go in your written account of the work, with a photograph beside each, so that nothing in the roof is described only in words. Our answer on whether foam stops tiles being repaired explains why repair has to wait until the foam is off.
Tiles, slates and stone tilestones
Broken or slipped covering is the most visible repair. For a few units the job is simple: lift the neighbours, slide out the broken piece, fit a replacement and re-fix. Which?, in a November 2025 survey (ex VAT), found £75 to £400 as the typical range for replacing one to six tiles.
The harder part is the match. A concrete tile from one maker will not sit square with a clay tile from another, and a new slate beside weathered ones shows. We match for size, profile, colour and thickness as closely as stock allows, and where a perfect match is not available we tell you and show you the closest.
Local sandstone tilestone is the county's traditional stone roofing, and the Herefordshire building stone atlas traces its main supply to St Maughans sandstone in the Golden Valley. SPAB describes Welsh slate and stone roofing as "predominantly double-lapped", meaning each course covers the joint below it twice, so a lifted stone can disturb more than one course. SPAB also advises: "Claims of unavailability or long delivery times should always be checked with the quarries."
Reclaimed pieces from the same roof can be the best match for a repair, and we keep sound ones from any area that has to be stripped. Where that is not enough, the quarries are the next call, and we ask them directly instead of relying on a merchant's word, since delivery times and stock change from one quarry to the next. Tilestone is replaced with tilestone, and any change of material is talked through with you first, together with the building control and planning checks that a change of covering can bring.
Battens and underlay: the layers between
Under the covering, two layers decide whether the repair lasts. Battens are the thin timbers the tiles hang from. The underlay is the sheet beneath them.
Battens that were covered by foam are checked along their full length. We probe the ends and the points where each batten crosses a rafter, where moisture would gather. Sound battens stay in place. Soft or split ones are replaced, and the new ones are fixed to the spacing the tiles need. The gauge, the distance between battens, follows the covering, because a slate, a plain tile and a stone tilestone each need a different one. Setting battens out afresh is also the moment to check that the roof lines up along the eaves and verge, so the new work sits level with the old.
Underlay that has torn or come away with the foam is renewed. A small tear can be patched between two battens, but a sheet damaged across much of a slope is replaced across that slope. Our guide to new underlay after foam removal explains the choice between sheets, and the guide on what spray foam does to roof timbers explains what we are looking for in the wood.
| Layer | What we check | Likely action |
|---|---|---|
| Battens | Softness, splits, nail rust | Replace the weak, keep the sound |
| Underlay | Tears, lifted laps, patches | Patch small tears, renew large areas |
| Rafters | Dampness, staining, softness at the ends | Leave to dry, or cut out and sister in new timber |
The skyline: ridge, verges, chimney and valleys
We look at the high edges of a roof first, and after foam removal they get a second look from underneath. The ridge is the top run of capping. The verge is the edge at a gable end. Valleys are the internal gutters where slopes meet, and the chimney has flashings and flaunching, the mortar collar at the top of the stack.
Foam sprayed close to these lines can hide a gap in bedding or a lifted flashing, and the joint is checked from inside and out. Ridge and verge repairs bring in a standards point. Marley says that installing to BS 5534 "isn't required by law", yet the 2015 amendments to that standard "made it clear that mortar could no longer be relied upon as the only means of securing the roof covering". Mortar is not banned. It is no longer enough alone, so a ridge or verge we rebuild is secured with fixings as well as mortar.
Which? (November 2025 survey, ex VAT) gives a new ridge tile as £80 to £300. MyJobQuote gives £225 to £550 as the 2026 average for ridge tile replacement, and around £200 to patch a chimney lead flashing, as typical UK ranges, each dated by the page it comes from.
Our work at the skyline is not separate from the foam job. If the foam ran up to a ridge, and the ridge is now loose, the two repairs are planned together so that the roof is not opened twice. A ridge that is rebuilt once is worth more than one that is patched twice. The same goes for a verge, where the cement or the dry-fix cap is replaced along the whole run rather than in short lengths.
When a repair grows into re-covering: England and Wales
Some repairs after foam stay small. If a slope needs stripping and re-covering, the question is whether Building Regulations approval applies, and the answer differs across the border. We put it to building control, the council or a registered building control approver, before the work.
- England: the Planning Portal sets two tests, one on whether less than 25 per cent of the total building envelope is affected and one on whether less than 50 per cent of the roof is. Meeting both normally means no application is needed.
- England: the Planning Portal treats a new covering that adds 15 per cent or more extra weight to the roof as needing approval. AD A, in its para 4.4, says a significant change is when "the loading upon the roof is increased by more than 15%".
- Wales: the Welsh Government opens with the position that approval is needed "In most situations" for re-roofing, and its roof page adds that replacing or repairing "more than 25 per cent of the roof area" would normally bring a requirement to improve the roof's thermal insulation.
- Wales: the Welsh AD A also uses "more than 15%" for a significant change in roof loading.
These tests measure area and weight, so we measure the area at the survey. A repair that stays in a few tiles may not come near either test. A slope that must be stripped may.
If the roof also has a roof window or a dormer, planning rules differ again. Our planning guide for roof windows covers those, and we do not restate them here.
What third parties say repairs cost, and how we price
The figures below come from published guides and not from us. Each is a typical UK range with its source named, and the unit is part of every figure.
| Repair | Figure | Source |
|---|---|---|
| One to six tiles | £75 to £400 | Which?, November 2025, ex VAT |
| New ridge tile | £80 to £300 | Which?, November 2025, ex VAT |
| Roof repair, average | Around £650 | MyJobQuote |
| Ridge tiles, average | £225 to £550 | MyJobQuote |
| Chimney flashing, full | Around £570 | MyJobQuote |
Prices for the same job vary from house to house, and the roof in front of us sets the real number. Treat each figure as a marker for that one job. None of them scales up into a total for your roof, and they cannot be added together.
On a real house, what sets the price is the covering and how easily it can be matched, the number of battens and the area of underlay, the height and access, and whether a ridge, flashing or verge needs rebuilding. Scaffold, where it is needed, sits in the written quote, and on the public road we arrange the licence with our scaffolder. After the survey, a single written figure covers the repairs and the foam work together, and the quote should say whether VAT is included.
Old battens, broken tiles and offcuts leave with us, and the loft and the drive are swept before we go.
