Short answer
It can raise the risk. According to the Energy Saving Trust, foam sprayed straight onto the roof's underside "will partially seal the timber", though with open-cell foam the risk "should be much lower". Foam does not rot wood on its own, because rot needs damp. What matters is whether damp can reach the timber and whether the timber can dry out. We expose the rafters and battens, then photograph what we find.
What partial sealing does to a rafter
A roof timber sits in a cold, moving space under the tiles. Left bare, it can give up moisture to the air around it. Foam sprayed hard against it changes that, because the covered faces of the rafter and batten can no longer release damp into the loft. If a patch is already wet, the foam keeps it that way, and a roof that was fine for years can start to fail behind the foam without any sign in the rooms below.
The two foam types treat this differently, and the Energy Saving Trust describes how:
| Foam | Its description | What it means for timber |
|---|---|---|
| Closed-cell | Not vapour permeable | Moisture cannot pass through it |
| Open-cell | The more vapour permeable | Some moisture can pass, so the risk should be much lower |
Lower is not nil. A rafter under open-cell foam can still be damp from a leak, and nobody can tell from the loft side whether it is, since the foam covers the evidence. Our guide to what spray foam does to roof timbers sets out what we look for once the wood is visible again.
Where the damp comes from
Timber rots when it stays wet, and two routes bring water to a foam-lined roof. The first is a leak from outside: a slipped tile, a cracked slate, a worn flashing at a chimney or a failing valley. Water that gets past the covering meets the foam and can run along its face before it shows anywhere. A stain on a bedroom ceiling may be a long way from the real opening.
The second is condensation from inside the house, which settles on a cold surface and needs somewhere to go. With foam fitted wrongly, or on a roof that has no airflow at the eaves, it can build up on the timbers and in the layers around them.
Signs worth reporting, whichever route it is, include:
- a musty smell in the bedrooms below the roof
- brown rings or patches on a ceiling
- damp-looking foam at the eaves
- nails or fixings with rust trails
- spongy timber when pressed
None proves rot, but each is a reason to inspect. A stained rafter and a soft rafter are separate problems, and only an inspection separates them. The same goes for a damp batten, which may simply have been wet once and dried, or may still be taking in water today.
What we check when the foam comes off
Rot can only be confirmed with the timber in view, so the check happens during removal, bay by bay. Once a section of foam is lifted, we look at the wood in daylight and by lamp. Staining and decay are different things, and the difference decides the work: a dark mark on sound wood needs nothing, while a rafter that gives under a spike has lost its strength.
The places we go first are the lower ends of the rafters, where they reach the wall plate, and the areas around chimney stacks, valleys and roof windows. Those are the points where water meets the foam from outside, so they are where rot can start. Each finding is photographed before anything is touched, which also means you can see the evidence rather than take our word.
If timber has failed, the repair depends on what it carries. A small area of surface damage may be treated, but a rafter foot that has lost section can need a new piece fixed alongside the old. Our page on repairs after foam removal covers what follows, and the sound timber then goes back under new insulation.
Rules to know on each side of the border
Timber repairs on their own may not need an application, but the re-covering and re-insulating that can follow may. In England, the Planning Portal sets two tests for going without an application: under 25 per cent of the total building envelope touched, and under 50 per cent of the roof. In Wales the position is stricter: the Welsh Government says that approval under the Building Regulations will be needed for this kind of work in most situations, so we ask the council's building control team before we start.
Both sides treat the roof as a thermal element, so new insulation has to meet the Approved Document L figure for that nation. We set out those figures in our answer on the insulation level after foam removal.
Lenders come into it as well. RICS said in March 2023 that some lenders had shown concern, equity release mortgages among them, so put the question to yours. If rot is found, a record of what was done is worth keeping. Our spray foam removal page explains the order of work. The written price is one total, set after the survey, and scaffold is already inside it.
