01432 610152 Get a quote Call 01432 610152

Slate roof ridge

What goes on the ridge of a slate roof?

The top of a slate roof is capped with separate ridge pieces that cover the join between the two slopes, held down by mortar, mechanical fixings, or both.

In brief

Slates cannot bend over the top of a roof, so the join where two slopes meet is closed with separate ridge pieces laid end to end. They are clay, concrete, stone or cut slate, and the slates on each side stop short so the caps can sit across the gap. Since the 2015 amendments to BS 5534, Marley says, a bed of mortar has not counted as sufficient fixing on its own, so a modern ridge also carries mechanical fixings.

The pieces that cap a slate ridge

A slate is a flat slab and the top of a roof is an angle, so the join between the slopes needs its own covering. Slates on each side run up to the ridge line without meeting, and the gap is closed by ridge pieces laid along the top, each overlapping the next.

The choices that suit a slate roof include:

  • clay ridge tiles, angled or half-round
  • concrete ridge tiles, made to match a concrete roof tile
  • stone ridge pieces, cut to sit with a stone roof
  • cut slate ridge pieces, where the roof is slated throughout

The ridge is the first place we look on a survey, because it sits on the skyline and takes the full force of a gale. The pieces can crack, shift along the line or lose the bedding beneath them. A broken cap exposes the join at the one point where the slates cannot help.

A ridge that has moved can also be a sign that something lower down is moving too, so we look along the line from the gable end and from the ground before climbing.

How a ridge is fixed: mortar, clips and screws

For generations ridge pieces were bedded in mortar and left at that. Marley, a tile and slate maker, reports that the 2015 amendments to BS 5534 made plain that a mortar bed by itself no longer counts as enough to secure the roof covering. It adds that installing to BS 5534 is not required by law, so the standard describes good practice and does not bind a homeowner. Mortar has not been banned. It now has a mechanical fixing alongside it.

A modern ridge therefore carries both a bed and a fixing, and the fixing is what holds a piece if the bedding fails. Dry-fix systems use mechanical fixings in place of wet bedding for the cap, and BS 8612 covers dry-fix.

Fixings need care on slate because the material is thin and brittle at the edge. A screw or clip driven in the wrong place splits the slate beneath it, so the ridge line is set out against the slates before any cap is laid. The page on nails or hooks for slates covers the fixings used lower down the roof.

What published guides say a ridge repair costs

Ridge figures come from three published sources, each in its own unit, and they are not combined.

  • Which? surveyed Trusted Traders in November 2025 and gives £80 to £300, excluding VAT, for a new ridge tile.
  • MyJobQuote gives an average of £225 to £550 for ridge tile replacement in 2026.
  • Checkatrade puts ridge tile repairs at £50 to £70 per metre, excluding VAT, as of June 2026.

The last of those is a rate for a length of ridge, while the other two describe a job, so a per-metre rate is never multiplied into a total. None of the three is specific to slate roofs or to this county.

What decides the written price here is the length of ridge, the number of pieces to reset or replace, the height of the work and whether the cap is mortar-bedded or dry-fixed. Our guide to ridge and verge repairs goes through a repair step by step. Scaffold is part of that single written price, and VAT should be checked in any quote you compare.

Ridge work under England's and Wales's rules

Re-bedding or replacing a ridge is repair work, and the thresholds that matter differ across the border.

  • England: no Building Regulations application is normally needed, the Planning Portal says, where less than 25 per cent of the building envelope and less than 50 per cent of the roof is affected; a ridge on its own sits far below both.
  • Wales: the Welsh Government's roof page ties insulation upgrades to replacing or repairing more than 25 per cent of the roof area, which a ridge repair is nowhere near.
  • Listed houses: wherever the work touches character, the 1990 Act sets the consent for England, and the Historic Environment (Wales) Act 2023 sets it for Wales.

Ridge colour and profile shape how a roof is read from the road, so on an older house the replacement is chosen to match. Our slate roofing page covers the roof below the ridge, from the first course to the last, and the ridge pieces are chosen to sit with whatever the slope below is made of. The survey ends with one written total, and the photographs show the ridge from above, piece by piece.

Related questions

Can a slate ridge be re-bedded in mortar alone?

Mortar still has a place as the bed, but Marley says a mortar bed alone has not counted as enough since the 2015 amendments to BS 5534. A ridge now carries a mechanical fixing as well. BS 5534 itself is not required by law, so we weigh the standard against the age and listing of the house.

Do all the ridge pieces have to be replaced if a few are cracked?

Not necessarily. Sound pieces can be lifted and re-bedded with a fixing, and cracked ones replaced to match in profile and colour. We photograph each length of the ridge from above before any piece is touched, so you can see which are cracked and which are only loose in their bed.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing