01432 610152 Get a quote Call 01432 610152

Heavier coverings

Does a heavier roof covering need approval?

Yes, if the new covering adds enough weight. The route is Building Regulations approval with a structural check, not planning permission.

In brief

It can. In England, the Planning Portal draws a line at 15 per cent or more extra weight from a new covering material. It is dealt with under the Building Regulations, never planning. In Wales, the Welsh Government calls a switch of material likely to need approval, using slate to tiles as its example. Either way, the roof structure has to be shown capable of carrying the new load.

What the approval is protecting

What you see from the street is the thin outer skin. Beneath it are the battens, the rafters, the purlins and finally the walls, and each was sized for the covering the house carried when it was built or last re-roofed. Lay something heavier on top and the spare capacity in all of them shrinks.

That is the reason Building Regulations step in. Their concern is that the roof stays stable, that fire performance is not worse, and that the energy performance of the roof is not lost in the change. Planning permission is a different system, concerned with how a building looks and what it is used for, and it does not govern the weight of what covers a roof.

So the question for a change of covering has two halves. Will it need approval? And does the structure need checking? The first is a matter of the thresholds below. The second is a matter of what we find in the loft: the sizes and spacing of the timbers, their condition, and any earlier alteration to them. The photographs from that look go with the written price.

England: the Planning Portal's 15 per cent line

At an English address the Planning Portal gives a plain test, in its own words: approval is needed if a new covering material pushes the weight of the roof covering up by 15 per cent or more. We quote it and name it because the figure is easy to misremember. Note the words or more: a covering that adds exactly 15 per cent is caught, and this is a test of weight, separate from the envelope test.

Three points follow from it:

  • the comparison is old covering against new covering, so the weight of each has to be known
  • the weight per square metre of a product comes from its manufacturer's data sheet
  • the line is at 15 per cent or more, so a covering that lands exactly on it is caught

This test stands apart from the Portal's other one, which looks at whether work affects under 25 per cent of the total building envelope and under 50 per cent of the roof. A full re-roof can pass one test and fail the other. A like-for-like re-cover in a lighter material may clear the weight test, and still raise questions about energy performance, which we cover in building regulations for a new roof in England.

Wales: the Welsh Government's slate-to-tiles example

Wales words it another way, so the English figure should not be carried across the border. The Welsh Government's re-roofing page opens with a general rule: in most situations a re-roof will call for Building Regulations approval. It then singles out a change of material. Take slate swapped for tiles: approval is likely to be needed so the roof stays adequate in structural stability. The test it gives is a tile that is significantly heavier or lighter than what is there now. Fire safety and energy efficiency are covered by the same sentence.

Two details are worth holding on to, because they are easy to lose when the rule is retold. The page says lighter as well as heavier, so a move from heavy to much lighter is also caught. And it says likely, so building control, whether the council's or a registered approver's, has the final word on your roof.

Our page on swapping slate for tiles in Wales takes that example in full. Planning is a third question, which turns on appearance.

How a change of covering is handled

The order of work is identical whichever side the house stands. We survey the roof, photograph the structure and record what the existing covering is. We find the weight of the old and the new from the data sheets, and we say plainly which side of the line the change falls. Then the approval route is chosen: the council's building control service or a registered building control approver, and the application goes in before any covering is ordered or stripped.

Choosing between coverings is partly a weight matter and partly a money one. In its guide of 30 September 2025, HomeBuilding gives £10,000 to £15,000 for a 65m² semi with plain concrete tiles, with Welsh slate for that house putting the figure at up to £18,000. Those are guide figures from a third party, not ours, and the difference is a reminder that the covering is a big part of the price.

For the choice itself, see choosing a new roof covering. The full job sits under roof replacement. Our own quote comes after the survey and gives a single total.

Related questions

Do I need planning permission to fit a heavier covering?

No, the weight of a covering is a Building Regulations matter. Planning can still matter where the look of the roof changes, such as on a listed house or inside a conservation area. That is a separate test about appearance, and the approval for weight follows its own route.

How would I know whether the weight rise reaches the English line?

Set the weight per square metre of the old covering against the new, taking both from the makers' data sheets. A surveyor or roofer can do that sum for you before anything is ordered, and should show their working. At a Welsh address the question is put differently, as significantly heavier or lighter, so building control gives the final answer.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing