Short answer
A bargeboard, sometimes called a verge board, runs up the sloping edge of a gable end, from the eaves to the ridge. It covers the cut ends of the roof timbers under the overhang and shields them from the weather. A fascia does the same job along the eaves, where the gutter hangs. Bargeboards carry no gutter, but they do sit beside the verge.
Where bargeboards sit and what they do
On a gable-ended house, the roof stops at a sloping edge called the verge. The roof timbers there stick out slightly past the wall to make an overhang. A bargeboard is nailed or screwed across the ends of those timbers, so the end grain is covered and the overhang looks finished.
It protects the wood behind it in two ways. It keeps rain from the cut ends of the rafters or purlins, and it gives the outer edge of the roof covering something solid to finish against. The verge tiles or slates sit just above it, bedded in mortar or fixed mechanically, so a bargeboard that moves can loosen the verge as well.
Fascias run horizontally along the eaves and hold the gutter. Bargeboards slope with the roof and hold nothing. A gable-ended house has both (a hipped roof has no verge, so no bargeboard at all), and on a timber-framed gable, such as those in the black-and-white villages of north-west Herefordshire, the board is part of how the gable looks as well as a cover for the timbers underneath.
Timber or uPVC
Older bargeboards are timber, painted or stained. Some are plain planks, others are shaped or carved at the lower end. Timber lasts when it is kept painted and the top edge stays dry, but the top edge is where rain settles. A rotten bargeboard shows as soft paint, a dropped lower end or a gap against the verge.
uPVC boards are the modern alternative. They do not rot, though one retailer of plastic boards says they can typically keep performing for 20 to 40 years, which is the seller's own claim. On a plain gable they ask less upkeep. Colour and finish matter on a gable, since it faces the road, and a new board is best matched to the other woodwork.
On a house with shaped timber boards, plastic is not a like-for-like swap, and the choice changes the look of the gable. Our page on ridge and verge repairs covers the roof covering that meets the board. The repair is matched to how that particular gable was built, which is why we look at the board, the verge and the timbers behind them together before suggesting anything. Check what the other gable of your house has too, because one mismatched board stands out from the road.
Listing, wildlife and asbestos rules at the verge
A bargeboard is part of the roofline, so the same checks apply as for fascias.
- Listed building consent applies when work alters a listed house's character: section 7 of the 1990 Act in England, sections 88 and 89 of the 2023 Act in Wales.
- HSE advises treating a building built or refurbished before 2000 as a possible source of asbestos, so boards and soffits on older houses are checked before anything is cut.
- Bats are protected, roosts included, and licences come from Natural England in England and Natural Resources Wales in Wales.
- Section 1 of the Wildlife and Countryside Act 1981 is the law on nests: intentionally harming one that is occupied or being built is an offence, so work waits while a nest is active.
A house in a conservation area or a National Landscape can carry extra planning controls on either side of the border. Check with the council first, and inside the Bannau Brycheiniog National Park check with the National Park Authority. We ask these questions at the survey, before a price is set. For a Welsh house in a conservation area, ask the council, or inside the Park the National Park Authority, whether changing the board's material is a planning matter.
What replacing a bargeboard involves
Because the board is fixed to the roof timbers, replacing it can mean lifting the verge tiles or slates beside it. That is where the work becomes a roofing job rather than a carpentry one. A new board has to be set to the right height, flush with the underside of the verge, so the first tiles can be re-bedded or fixed against it.
The survey photographs show the top edge, the lower end, and the junction with the gutter at the eaves. Where the bargeboard meets the fascia, the corner is a spot where both boards can rot, so we look at the pair together.
Sound timber with one bad section can sometimes be spliced, and when that is the better buy, the quote recommends it. A written total follows the survey, with the work, the verge and the clear-up all inside it. Our guttering, soffits and fascias page lists the rest of the roofline work, and the site is left tidy once the verge is closed up again. If the boards look soft, our signs of rotten fascias page lists the checks, and the same checks apply to a bargeboard.
