01432 610152 Get a quote Call 01432 610152

Eaves airflow

Soffit vents and eaves airflow

A soffit vent lets air into the roof space at the eaves. This guide explains what the gap is for, the figures a manufacturer gives, and what to protect when soffit boards are renewed.

Horizon Roofing Hereford 9 min read

Beneath the overhang of a pitched roof sits the soffit, the panel that closes the space from the edge of the roof to the wall. On some houses that panel is solid. On others it carries a row of small holes or a long slot, and those are soffit vents. Their job is to let outside air into the roof space, where it can move along the underside of the covering and carry off damp air that would otherwise condense on cold timber.

How much airflow a roof needs depends on its construction. A cold roof with one kind of underlay has one requirement, a roof with another kind has a second, and a warm roof with the insulation in the rafters has a third. The eaves are only one part of the arrangement, but they are the part most easily covered over by accident, by insulation, by paint or by a replacement board with no vent.

This guide covers a manufacturer's figures, how the underlay changes them, how blocked eaves show themselves, and what to ask when soffits are renewed. It belongs to our guttering, soffits and fascias service.

What a soffit vent is for

A cold roof is one where the insulation lies along the loft floor and the space above is left cold. Warm, moist air from the rooms below keeps trying to rise into it. If that air has no way out, the moisture settles as droplets under the covering, on the rafters and on the felt. Over time it can darken timber, soften it and spoil the insulation. A roof built with the insulation in the rafters, a warm roof, is a different arrangement with its own ventilation rules, so a survey establishes which kind you have before anyone talks about vents.

Ventilation removes the moist air before it settles. Air enters at the eaves through vents in the soffit or at a gap behind the fascia, passes up the slope and leaves at the ridge or through vents high in the roof. The path only works if the entry is open. A soffit vent is therefore a small part with a large job, and a blocked one starves the whole roof.

Not every damp mark in a loft comes from lack of airflow, and not every leak is condensation. Our guide to condensation or roof leak helps tell the two apart, and a wet mark on a loft timber is always worth tracing to its source.

The vents come in a few forms: a continuous strip along the soffit, circular discs set at intervals, or a ventilated board with the slot built in. They also let the eaves timbers dry out if a gutter overflow ever wets them.

The figures a manufacturer gives for a cold roof

For the sizes themselves, the source is Marley, which makes roof tiles and ventilation products. Its cold-roof guidance, written for roofs laid with high resistance (HR) underlay, gives the eaves openings below. They rest on BS 5250, the standard on moisture in buildings, whose status is current and under review.

Marley's eaves openings where HR underlay is used
Roof pitchOpening along the eaves
15 degrees or less25mm, along the whole eaves
More than 15 degrees10mm, along the whole eaves

In England, Approved Document C (2013) cites BS 5250:2002 for the condensation requirement, at para 6.10, so a surveyor may refer to either the current edition or the older one. BS 5250 is one British Standard for England and Wales, and Marley's figures apply to its products in both.

The openings are measured along the whole length of the eaves, not per vent. A row of small discs spaced far apart can add up to less than the strip the table asks for. That is why a surveyor looks at the total area of opening, and why a handful of vents added at random may fall short.

These are manufacturer figures for one roof type. They do not replace the data sheet of the products on your roof, and your roof may call for more. A roof with a long run of eaves broken by a dormer, a porch or a flat-roofed extension needs the openings checked on each separate stretch, since air entering one stretch cannot serve another.

HR and air-permeable underlay: why it changes the answer

The underlay is the sheet under the battens, and its type decides how much the eaves must do.

Underlay of the high resistance type (HR) is not vapour-permeable, so moist air cannot pass through it, so the roof space needs the eaves openings in the table above, and openings at the top of the slope as well. Air-permeable underlay, also called LR, behaves differently. Marley's position for air-permeable underlay, where the ceiling below is well sealed, is that "fortuitous ventilation at the eaves via normal eaves construction (3mm) is all that is required, provided the requirements of UKAS Third Party certification are fully met".

Each type comes with a condition attached:

  • HR underlay needs the eaves openings in the table, kept clear at all times
  • air-permeable underlay can rely on normal eaves construction only with a well-sealed ceiling and the product certification in place
  • a roof where neither condition can be shown needs its ventilation worked out for that roof

Which underlay your roof has is not always plain. In the loft it may be visible as a sheet over the rafters, or it may be missing altogether on an older roof, where the tiles or stone can be seen from beneath. From outside, the edge of the underlay can sometimes be seen at the eaves above the fascia.

If you are unsure, the survey records the underlay, the ceiling and the eaves, and the photographs show what each one looks like. We then explain what the roof needs in plain terms, with the data sheets to hand.

Insulation, paint and other things that block the eaves

Blocked eaves can be the side effect of work done for another reason. Loft insulation is pushed along the floor until it reaches the wall plate, and in doing so it covers the gap where air should enter. A roll tucked tight into the corner is one example. The remedy is a rigid tray or baffle set at the eaves, which holds the insulation back and keeps a channel open above it.

Other things that close the gap:

  • paint applied thickly over a perforated soffit board
  • a replacement solid soffit fitted without a vent
  • old nests and debris packed behind the fascia
  • spray foam applied across the eaves, which seals the roof space entirely
  • a gutter mounted so high that it presses on the bottom tile row

Where nests are involved, section 1(1) of the Wildlife and Countryside Act 1981 makes it unlawful, in England and in Wales, to intentionally harm a nest that birds are using. A nest in use waits until the birds have left. Our guide to birds nesting behind fascias and soffits covers the law in more detail.

Spray foam in the roof is a separate subject, with its own questions about ventilation and about lenders. It is dealt with on our spray foam pages, and the eaves must not be treated as an afterthought when foam is removed.

Birds are not the only occupants. Wasps and bees can use an eaves gap, and a vent that has been stuffed with nesting material or insect debris passes almost no air at all, however large the slot looks from the ground.

Replacing soffits: keeping the airflow

Soffit boards come down when they rot, when birds or insects have got behind them, or when the fascia and gutter are renewed. That is the moment to look at ventilation, because the new board decides whether the eaves breathe.

Points to settle before the new soffit goes up:

  • whether the old board was vented, and where the vent sat
  • what the roof's underlay is, from inside the loft or at the edge
  • the total area of opening the new soffit gives, measured along the eaves
  • whether insulation has been pushed up against the wall plate behind it
  • whether the board is timber, plastic or something that needs a particular fixing

A soffit can also hold asbestos. HSE lists "AIB white soffit panels to underside of roof eaves" among the locations of asbestos insulating board, and says licensed work covers most AIB removal, with only short-duration work non-licensed. The board is left alone until the survey says what it is, and any licensed work is passed to a specialist holding the licence. Our guide to asbestos soffits covers the difference between AIB and asbestos cement, and the waste rules in England and in Wales.

If the building is listed, the soffit is part of the roofline, and consent questions arise as they do for any roofline change. A vented board of a different look from the original is exactly the kind of detail to describe to the council before ordering.

Signs that the eaves are not breathing

The evidence of poor airflow shows in the loft and at the roof edge. It is worth looking after a cold spell, when condensation is most likely to appear.

Signs of poor eaves airflow and where to look
SignWhere to lookWhat it may mean
Dark spots on rafters near the eavesLoft, at the wall plateMoist air settling with no way out
Droplets under the feltLoft, along the slopeCondensation on a cold surface
Insulation pressed tight to the wallLoft, at the eavesThe entry gap is covered
A solid soffit with no slot or holesOutside, from belowNo entry point at all
Mould on the ceiling in cold cornersBedroom or landingMoist air from the room, not the roof

No single sign proves a ventilation fault, and each one has other causes. A leak, a blocked gutter and a gap in the ceiling can all leave the same marks. That is why the survey looks at the whole roof, and why we photograph what we see before suggesting anything. A reading taken in the loft on one cold morning proves little, and a second look in different weather, with the photographs from the first visit beside you, tells you more than any single visit.

If the roof itself is being replaced, the same questions arise there, and our answer on whether a new roof needs ventilating covers them. You receive the photographs and one written total price for whatever the survey shows is needed.

Soffit vents: your questions

Can I fit vents into a solid soffit myself?

Cutting a slot or fitting a disc is simple in a timber or plastic board, but the total opening matters more than the number of vents, and Marley's table asks for an opening along the whole eaves. Find out what the board is made of first, because an old white soffit may be asbestos insulating board and must not be cut.

Do all roofs need soffit vents?

Not every roof. Marley says air-permeable underlay can manage on normal eaves construction when the ceiling below is well sealed and the product certification is met. HR underlay, which is not vapour-permeable, needs the eaves openings in its table. The survey records which underlay your roof has.

What stops loft insulation blocking the vents?

A rigid baffle or tray set at the eaves keeps the insulation back from the wall plate and leaves a channel for air above it. It is fitted from inside the loft, and it matters most when more insulation is added. Look for insulation pressed against the wall before assuming the soffit is at fault.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing