01432 610152 Get a quote Call 01432 610152

Flashing leaks

Chimney flashing leaks: apron, steps and back gutter

A chimney is sealed by four pieces of lead, and a leak can start at any of them. This guide names them, shows how each fails and explains the repair.

Horizon Roofing Hereford 9 min read

A chimney is the one place where a tall masonry column has to be made watertight against a sloping roof, on every side at once. The joint is not sealed by the stack itself. It is sealed by lead, cut and dressed to fit, tucked into the masonry above and laid over the tiles or slates below.

When that lead lifts, splits or loses its fixing, water gets behind it and runs down the inside of the stack or onto the timbers. The stain then appears on a ceiling or a chimney breast, sometimes some distance from the gap, which is why a flashing leak can be mistaken for a fault elsewhere on the roof.

The sections below name the four parts of a stack's lead, explain how each one fails, set out the lead codes and the costs quoted by third parties, and deal with the rules that apply when flashing work turns into a larger job, on both sides of the border. For other stack repairs, start from our chimney repairs page.

Apron, steps, back gutter and soakers

Four pieces of lead work together around a stack, and a fault in any one can let water in.

The lead around a chimney
PartWhere it sitsWhat it does
ApronAcross the front face, at the bottom of the stackThrows water down onto the slope
Step flashingsUp the sides, stepped along the slopeSeal each side against the masonry
Back gutterBehind the stack, where the slope rises to itCollects water and carries it round the stack
SoakersUnder tiles or slates, beside the stackCarry water out across the slope

Soakers are small pieces of lead folded to an angle, slipped beneath each course of tile or slate and turned up against the stack. The step flashings lie over the soakers, with the top edge pushed into a slot raked out of the mortar joints. That groove is the raglet, and it is the weak point of the whole arrangement.

Where the stack rises through the roof away from the ridge, the slope above it sends water down against the back face. The back gutter turns that water aside. A stack with a good apron and sides but a blocked or split back gutter will leak whenever rain is heavy enough to fill it.

Herefordshire's stone atlas calls the tall external stacks of its black-and-white buildings "commonly of local sandstone". Stone lacks the regular face of brick, so the lead is dressed to it joint by joint. Our guide to the back gutter behind a chimney takes that part in more detail.

How a flashing fails, and how it shows indoors

Lead does not leak by itself. A flashing leaks when it has come away from what it was keeping out, or when the masonry behind it has changed. Look for these on the roof, from the ground with binoculars:

  • a strip of lead peeling away from the brickwork and standing proud of it
  • lead cracked open along a fold or a seam
  • pointing in the raglet that has fallen out, leaving the lead unsupported
  • a filler of sealant or cement that has cracked and pulled away
  • moss, leaves or grit packed into the back gutter

Where the damp appears indoors helps to tell the parts apart.

Where the stain shows and what it suggests
StainLikely part
On the breast, low downApron or step flashings
On the breast, high up or in the loftBack gutter or the stack itself
On a ceiling beside the breastSoakers or the roof edge
On the breast only after driven rainOne side's step flashings

The table is a starting point. The mark is where the water arrived, and the gap may lie higher up the roof. In the loft, a torch shows tide marks on the timbers around the stack, damp on the brickwork and daylight where the roof should be closed. Step only on the joists while you look.

A survey follows the path in the loft first, then confirms the fault from outside, so you see photographs of what we found before any repair is agreed. A flaunching crack at the top of the stack can mimic a flashing fault, so we check both, and the guide to flaunching on top of the stack explains that part.

Which lead code goes where

Lead for roofing is sold in codes, each number standing for a thickness. The table below comes from Royston Lead's cast-lead brochure, and the letters in its last column are the brochure's own use letters: soakers take A, flashings B, pitched valley gutters C, parapet and box gutters D and dormers E.

Lead codes as printed by Royston Lead
CodeThicknessColourUsed for
31.32 mmGreenA, recommended for lead soakers only
41.80 mmBlueA, B, C, E
52.24 mmRedB, C, D, E
62.65 mmBlackB, C, D, E

A flashing falls under use B, so it comes in code 4, 5 or 6, and code 3 is for soakers only. Which code a stack takes is decided on the roof, from the lengths involved and the exposure of the joint, and the code is written on the quote so you can check it against this table.

BS 6229:2025 deals with flat roofs that use flexible waterproof coverings, and it covers membranes only, so it does not apply to lead. Approved Document C cites BS 6915:2001 for lead.

Lifespan figures vary by source and are ranges, not promises. For a chimney flashing the line that applies is MyJobQuote's: lead flashing "can last for over 80 years", a hedge about what is possible, since the longer HomeBuilding and Less ranges are for lead flat roofs. A well-fixed flashing that has outlived its pointing, or its support, still needs repair long before the lead itself is worn out.

Repair, refix or replace

The right repair depends on what the survey shows. Three outcomes cover the possibilities.

  • Re-fix and re-point: the lead is sound, but the raglet has lost its mortar. The lead is dressed back and pointed in.
  • Patch: a split or a short length has failed. A new piece is let in and lapped over the old.
  • Replace: the lead has worn through, been repaired many times or lost its shape. The stack is re-flashed with new lead of the right code.

A bead of sealant across a lifted edge is not a repair, because it fills the gap without holding the lead. Our short answer on mastic and lifted lead explains why.

For scale, these are third-party figures with their sources:

  • MyJobQuote (September 2026): a chimney lead flashing patch repair costs around £200, and a full replacement averages around £570. Full leadwork is quoted at £350 to £920, "depending largely on whether scaffolding is required".
  • Checkatrade (June 2026, ex VAT): lead flashing repairs run £50 to £70 per metre.

Never multiply a per-metre figure by a length and call the result a total. What sets the price of your stack is the length of lead, its code, the state of the raglet and the access. Your quote arrives as a written total price and says whether scaffold is included.

When the job is done, ask for photographs of the finished lead, the pointing and the back gutter outlet. That gives you a record to compare against if a stain ever returns.

When flashing work grows into something larger

Re-flashing one stack is a repair. It becomes something else when it is part of a re-roof, when the house is listed, or when the stack is shared.

  • In England, if the flashings are part of a re-cover, the Planning Portal says no Building Regulations application is normally needed where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" is affected.
  • In Wales, the Welsh Government says of re-roofing: "In most situations, this work will need Building Regulations approval."
  • In England, listed building consent is needed before work that would change the character of a listed house (section 7 of the 1990 Act). In Wales, the Historic Environment (Wales) Act 2023 section 88 requires works to be authorised.

On a shared stack, the Party Wall etc. Act 1996 applies in both countries. Its section 2(2)(j) covers cutting into the neighbouring wall to fit weather-proofing against it, and the building owner serves the notice. If the neighbour stays silent for 14 days, that counts as dissent and surveyors are appointed.

On either side of the line, ask who is checking the work. Building control is done by the council or by a registered building control approver. A flashing repair on its own is a repair, and a re-cover brings in the tests above. If the house is listed, matching the lead matters as much as sealing the joint. Our page on listed and heritage roofing covers how a repair is matched to such a house.

Scaffold on the road side

Stack work is the kind of job that can need a scaffold, because the lead sits high on the building. Under section 169 of the Highways Act 1980, a licence is required for any scaffold that stands on the highway, and our scaffolder and we sort that out together.

Each council sets its own fee, unit and notice period, and they should not be compared as if the units matched.

Two scaffold licence fees, England and Wales
CouncilFee and unitNotice
Herefordshire (England)£167 per licence, for a maximum of 1 month; £123 per month to extendAt least 10 days
Monmouthshire (Wales)£108 administration fee; £27 per week to extendAt least 5 working days

A scaffold in the garden or on the drive needs no highway licence, but scaffold on the pavement outside a terrace does. The written price covers the scaffold, so you are not asked for a separate sum later. Where a flashing repair is small and can be reached safely, a tower or a low-level platform may be enough, and the survey says which.

The notice periods in the table matter for planning the work. A licence takes time to arrange, so a stack that is leaking steadily is made safe first, with a temporary cover where it can be fitted from the ground or a safe platform, and the full repair follows once access is in place. Photographs of the leak before and after the temporary measure go on the file, so the permanent repair addresses the cause and not only the mark.

Chimney flashings: your questions

Why does my chimney only leak when rain blows from one direction?

Wind-driven rain is pushed against one face of the stack and into any lifted lead or open pointing on that side. The step flashing on that side is the usual suspect, with the apron next. A leak that shows only in one wind can still start from a gap that lets in water slowly in other weather.

Will a bead of sealant stop a chimney flashing leaking?

It can close a gap for a short time, but it does not hold lead that has lifted, and it hides what is behind it. A lasting repair re-fixes the lead into the cut joint and points it, or replaces the piece. We photograph the flashing first so you see which of those applies.

Does re-flashing a chimney always need a scaffold?

Access can be the largest part of the job, and MyJobQuote says full leadwork costs depend largely on whether scaffolding is required. A small repair that can be reached safely may need only a tower. Where a scaffold is needed, the written price includes it, and any highway licence is arranged for you.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing