01432 610152 Get a quote Call 01432 610152

Eaves trays

Why fit an eaves protection tray under the bottom tiles?

The lowest edge of a pitched roof is where felt, first tiles and gutter all meet, and a tray gives that meeting a proper shape.

Short answer

A tray for the eaves is a shaped plastic strip laid under the bottom course of tiles or slates. It props the underlay at the lowest edge and tips any water that gets beneath the covering into the gutter, away from the fascia and the rafter ends. It goes in when a roof is re-covered or the fascias are replaced, and it has to leave the eaves ventilation open.

What the tray does at the lowest edge

Any pitched roof has a layer of underlay beneath the tiles or slates, laid over the rafters. At the eaves, that underlay has to end somewhere, and it has to end over the gutter. Without support it can sag into the gap between the rafter ends and the back of the gutter, forming a shallow pocket that holds water.

The tray fixes this. It sits on the fascia and on top of the rafter ends, with its lower lip hanging into the gutter. The underlay laps over the tray, so any moisture running down the felt drops into the gutter instead of onto timber. The first row of tiles then covers the whole arrangement.

You may also hear it called an eaves carrier or an eaves support tray. It is a small part with a particular job: it keeps the end of the roof dry in the one spot where felt, board and gutter come together. Our guttering, soffits and fascias page shows the whole eaves line from the gutter up to the first course.

Why it is fitted with the fascia

The tray can only be set properly when the bottom course is off. That happens in two kinds of job: when the roof is re-covered, and when the fascias are replaced and the first row of tiles is lifted. In both, the underlay, the board and the tray are done together, so they fit.

A fascia fitted after the roof, without lifting the first course, leaves the edge of the underlay unsupported. On an older roof the felt may stop short of the gutter, or hang into it unsupported, and the rafter ends take the drip. A tray puts the water where it belongs.

It helps a replaced gutter too, because the tray lip and the gutter are set to each other. The new run needs the right height against the fascia, with the tray lip landing inside it, not behind it. Check this on a dry day, with the felt dressed down and a strip of paper passed under the lip. A gutter hung a few millimetres too low can leave a gap that spills over the back. Our fascias with a new roof page covers why the two jobs are best done in one visit.

Ventilation, asbestos soffits and wildlife

A tray must not block air that moves through the eaves. For a cold roof, Marley (a tile maker) sets eaves ventilation at 25 mm on pitches of 15 degrees or less and 10 mm on steeper ones when the underlay is HR, meaning high resistance. That type is not vapour-permeable, so the gap has to stay clear. A roof with air-permeable underlay and a tightly sealed ceiling can rely on 3 mm of fortuitous ventilation at the eaves, provided the maker's certification is met.

Exposed eaves bring other checks while the roof edge is open:

  • HSE names pale soffit panels as one place insulating board turns up in buildings from before 2000, and its removal is usually for a licensed firm.
  • Section 1 of the Wildlife and Countryside Act 1981 protects a nest in use or being built; it is an offence to intentionally destroy or damage it.
  • Bats are protected too. Bat licences are issued by Natural England for houses in England and by Natural Resources Wales for houses in Wales.

A licensed firm, a bat licence or an occupied nest can each pause the work, and we tell you so before a date is fixed.

What it adds, and when it can be left

The tray itself is a small item in the written total. What counts is the work of lifting the first course and the care taken, and when the roof is already being stripped the extra labour is low. Cost guides give no separate figure for a tray, so we quote none.

The rules sit with the re-roof rather than the tray, wherever the roof sits on the border. The Planning Portal gives its envelope and roof test for England, and gov.wales says that in most situations re-roofing needs Building Regulations approval in Wales. The tray is part of how the new roof is built to meet that.

When the eaves are sound and dry, and the felt already runs well into the gutter, a repair may not need a tray. We photograph the underlay at the eaves, show you the pictures, and say plainly when a tray is not needed. The survey gives one written price that reflects what the photographs show, and the site is left tidy afterwards. Our soffit vents and roof ventilation page covers the air side of the eaves.

Related questions

Can an eaves tray be added without taking the roof off?

Only by lifting the bottom course or two of tiles or slates along the edge. That is a small area, but it is a roofing job, and the old underlay at the eaves needs to be sound enough to lap over the tray. The survey shows which applies to your roof.

Does an eaves tray replace the soffit vent?

No. The tray deals with water and the soffit vent deals with air. Marley's eaves ventilation figures still apply, and the tray has to leave that gap open. Fitting one that blocks the gap trades a wet eaves for a damp loft, so we check the gap before the first course goes back on.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing