01432 610152 Get a quote Call 01432 610152

New over old

Can a new flat roof be laid over the old covering?

Sometimes a new flat roof covering can go over the old one, but only when the layers beneath are dry, sound and able to carry the extra load.

In brief

Sometimes. Laying over the old covering works only if the deck and any insulation under it are dry and sound, and if the added weight is acceptable. That is found out by opening the roof at test points, not by looking from a ladder. Where water is trapped in the old layers, or the old covering is blistered and loose, it comes off first and the new one goes onto a clean deck.

What must hold before laying over the old layer

An old covering is a surface, and a new one takes the shape of whatever it is stuck to. So the question is never only about the top layer. It is about everything under it: the insulation, the boards or slab, and the timber that carries them.

Before we would consider laying over, we open the roof in a few places and look at:

  • whether the insulation and the underside of the old covering are dry
  • whether the old layer is bonded down, or has blisters and loose areas
  • whether the deck is firm, or soft and stained in patches
  • how many layers are already there
  • whether any dips hold a pool after rain

HomeBuilding puts torch-on felt at 10 to 15 years, and Less at 10 to 20 years, so the age of the covering you have matters too. A layer near the end of its life is poor ground for a new one.

A new covering cannot cure ponding on its own. Where water sits, the fall of the deck needs looking at, and the page on ponding water on a flat roof goes through it.

Why wet layers and extra weight settle the question

Moisture is the first reason to strip. Water caught between the old covering and the deck cannot leave once a second covering seals the top. It lodges in the insulation or against the boards and can later appear as a ceiling stain that looks like a leak though no rain came in. The page on condensation under a flat roof deck explains how that differs from rain getting in.

Weight is the second. A second layer adds load, and the figures are written down. The Planning Portal's guidance for England sets the weight trigger at a new covering that adds 15 per cent or more to the load. Approved Document A (England) regards loading that rises by more than 15% as significant, and the Welsh Approved Document A sets the same 15% line for Wales.

A second layer may or may not stay under that line. It still has to be checked against the actual roof, and the result goes into the written price, not into a guess made from the ground.

Insulation and approval when you re-cover

Laying a new covering over an old one is still putting a new covering on that roof. The same questions come up as with a strip and replace, and we ask the council's building control service or a registered building control approver how they treat it before work is priced.

In England, the Planning Portal sets its application test at less than 25 per cent of the building envelope and less than 50 per cent of the roof. In England's Approved Document L, renewing a flat roof's waterproofing is classed as renovation, and Table 4.3 sets a 0.35 threshold with an improved figure of 0.16 W/m²K. Paragraph 4.13 allows the lowest feasible figure where 0.16 would not pay back within 15 years.

The Welsh Government's guidance for Wales is that re-roofing in most situations needs Building Regulations approval, and that for a flat roof whose insulation is part of the build-up, renewal may mean bringing the thermal element up to standard. Table 11.1 of the Welsh Approved Document L gives 0.16 W/m²K as the aim, with 0.35 as the worst figure accepted where 0.16 cannot be reached.

The insulation question is why a roof that looks fit for an overlay can still be better stripped: the layers that need improving are the ones underneath.

When stripping back is the better buy

Laying over is a narrow case, and where stripping is the better answer, that is what we recommend. The table sets out where each common finding points, and the survey photographs show which row matches your roof, so the decision rests on what was found.

What each finding points to
FindingRoute
Dry, flat, firmly bonded old layerOverlay can be considered
Blisters with damp beneathStrip to the deck
Soft or stained boardsStrip and replace boards
Pooling in the same spotCorrect the fall first

Which? gives its November 2025 survey figures for a typical single garage of 6 m by 3 m, ex VAT: £1,400 to £3,500 for a felt flat roof that keeps the initial structure in place, and £1,950 to £4,000 for new boards with modern products such as PVC or rubber EPDM. These are national ranges from Which?, and ours is a written total for your roof.

The warm deck or cold deck page and the flat roofing hub show what a full strip puts right.

Related questions

How do you know if the insulation under the old covering is wet?

By cutting small test openings through the covering and looking at what is beneath: dry or damp insulation, staining on the boards, and the underside of the old layer. Each opening is photographed and then sealed again, so what was found is recorded and shown to you rather than guessed at from the ground.

Does a second covering always cost less than stripping?

Not always. The published ranges from Which? separate a felt roof laid on the existing structure from one with new boards, but your total depends on what the test openings show. We give one written total once the findings are in, so the two routes can be compared on your own roof.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing