In brief
A plastic rooflight sheet is exposed to sunlight, to heat and cold, and to rain and dirt, every day for years. Over time the surface weathers, goes dull and yellows or crazes, and the material loses its flexibility. A sheet that once gave a little under a load now cracks. That is why old rooflights are treated as fragile, and why nobody steps on them. The remedy is replacement, planned from a safe platform.
What happens to a plastic sheet over the years
Rooflight sheets in an industrial roof can be plastic: glass-reinforced polyester, PVC or polycarbonate, each cast or extruded into the same profile as the metal sheets beside it. They let daylight into the building, and they are on the roof for the same reason the roof exists, to face the weather.
Sunlight is one agent of wear. Its ultraviolet part breaks down the surface of many plastics, and the sheet turns chalky, yellow or crazed with fine cracks. Heat in the day and cold at night make the sheet expand and shrink against its fixings. Dirt, moss and algae settle on the surface and hold moisture. Each of these takes a little flexibility from the sheet, and none of them shows from the ground as a break.
The result is a sheet that looks whole, lets in less light than it did and cannot take a load. The way a plastic sheet ages depends on its type and its maker, so we read the sheet in front of us, and the survey records its condition rather than guessing its age.
Why a brittle sheet is a fall risk
A rooflight is not built to carry a person. When it was new, it still was not, and by now it is weaker. The danger is that it looks like the roof around it. Once dirt covers it, it can be mistaken for a metal sheet, and a step onto it is a step into the building below.
HSE's guidance is blunt about asbestos cement, saying "AC roofs are always fragile", and a weathered rooflight in such a roof needs the same care. Our guide to fragile roofs and rooflights goes through the safe ways to work around them. The signs that a rooflight has gone beyond use are these:
- a colour change, from clear or white to yellow, grey or brown
- a chalky or rough surface that sheds powder when wiped
- fine cracks at the fixings or along the ribs
- a sag between the supports, or a sheet lifted at the laps
- stains inside the unit under the panel, where water is getting past
Nobody should test a panel by stepping on it. We check from a tower, a platform or the floor of the unit, then send you the photographs.
Repair, cover or replace the sheets
A brittle sheet cannot be repaired back to strength. The choices are about what happens to it:
- replace the rooflight sheets one for one, in the same profile and with a sealing washer under each fixing
- fit guards or covers across the panels, as a short-term measure when replacement must wait
- replace the roof sheets and rooflights together, where the metal around them is also failing
A one-for-one swap can be the best fit when the metal roof is sound. It does not mean the same sheets again, because the new panel must match the profile, its laps must close against the neighbours, and the light level should suit the work being done below. Our answer on replacing industrial rooflights covers the process step by step.
The new sheets are fitted from a platform or a boarded route, never from the old panel. If the roof around is asbestos cement, the survey comes first, because HSE says to assume asbestos in any building built or refurbished before 2000. We leave the roof swept and take the old sheets away.
Insulation values and approvals, England and Wales
Rooflights are part of the thermal envelope, so changing them can bring in the energy rules. The figures below are for dwellings, so for a unit or office, ask building control which values apply:
- In England, Approved Document L 2021 Table 4.2 gives 2.2 for rooflights when an existing dwelling gets a new roof.
- In Wales, Table 4.1 of the Welsh Approved Document L gives 2.2 for rooflights as well.
- In England, the Planning Portal sets the test for houses: no application normally, where "Less than 25 per cent of the total 'building envelope'" and "Less than 50 per cent of the roof" is affected.
- In Wales, the Welsh Government says re-roofing in most situations needs Building Regulations approval.
Swapping a few sheets is a small part of the roof, but the survey records exactly what is changing, so that the question can be put to building control with the facts to hand, and the answer kept with the building papers. Our commercial roofing page shows how the pieces fit, and the scaffold sits within the one price you are given.
