01432 610152 Get a quote Call 01432 610152

Repairing EPDM

Can a split in an EPDM roof be repaired?

A split in an EPDM roof can be patched when the rubber around it is sound. Splits in several places point to a bigger fault.

In brief

Yes. EPDM is a rubber roofing sheet, and a split can be cleaned, dried and covered with a rubber patch bonded on with the manufacturer's adhesive or tape. That holds when the sheet around the split is sound and the cause has been found. Splits along a seam, in a corner, in several places, or on a roof that ponds point to a wider fault, and a patch then only buys time.

How a split in rubber sheeting is mended

EPDM is laid as one large sheet, stuck down at the edges and joined at any seams. A split is a break in that sheet, and the repair is a second layer of rubber bonded across it. The order matters more than the patch itself:

  1. The split is found and its full length marked, including any hairline at the ends.
  2. The area is cleaned and left dry, to the standard the manufacturer's instructions set.
  3. A patch of EPDM, cut with rounded corners and larger than the split on every side, is bonded over it with the adhesive or tape that belongs to that system.
  4. The edges are pressed down and checked for lifting.

Rounded corners matter because a square corner is the first part of a patch to peel. We photograph the split and the finished patch, so you can see both.

If the rubber around the split has gone hard, chalky or brittle, it will not hold a bond, and the repair moves on to the next question: how much of the sheet is still sound. The rubber EPDM flat roofs page describes how a whole roof is laid.

Signs that a patch will not be enough

A patch cures one split. It does nothing for whatever caused it. The roof needs a wider look when the survey finds any of these:

  • a seam that is opening along its length, not at a point
  • splits in corners or at the upturns where the sheet climbs a wall, where the rubber is stretched hardest
  • more than one split, in different places
  • a pool of water that stays on the roof after rain, which the page on ponding water on a flat roof covers
  • wet insulation or soft boards beneath the sheet

Age counts as well. HomeBuilding gives EPDM 25 to 30 years and Less gives 30 to 50 years, and the two do not agree, so these are ranges and not promises. A roof well inside either range and with one clean split is a repair job. A roof near the top of its age range, with splits spreading, is a different case, and the page on how long EPDM lasts goes into the reasons for the gap.

When we think replacing is the better buy, the survey photographs show why.

What published prices say about repair and replacement

Third-party guides put numbers on both. They are typical UK figures, not Hereford prices and not ours. For repairs, Checkatrade's June 2026 guide gives £120 to £170 per m² for EPDM rubber, ex VAT, as a rate for patches up to a maximum of 3 m².

For a whole roof, MyJobQuote (page dated 09/10/26) gives an average of around £1,050 for rubber roofing in the UK, and says an installation takes between 2 and 3 days. The first is a rate for a small repair and the second is a figure for a complete roof. They describe different jobs, so one cannot be turned into the other, and a patch repair is not a part-payment towards a roof.

What moves a real price is what the survey finds: how big the damaged area is, whether the deck below is sound, how many upturns and corners there are, and whether access to the roof calls for scaffold. The written price comes after the survey, and if a patch is the sounder choice, the patch is what is priced. The flat roofing hub shows the other coverings side by side.

Approval if the repair grows into a new roof

A patch to a split is a repair. A new rubber sheet across the whole roof is re-roofing, and the border changes the rules.

England: on the Planning Portal's test, a re-cover normally needs no application while less than 25 per cent of the building envelope and less than 50 per cent of the roof is touched. In England, Approved Document L treats renewing a flat roof's waterproofing as renovation, so the insulation under a new sheet is looked at, with a threshold of 0.35 and an improved figure of 0.16 W/m²K in its Table 4.3.

Wales: the Welsh Government's advice is that in most situations re-roofing needs Building Regulations approval, while some flat roof repairs need none. Replacing a roof that carries its own insulation can mean improving that layer too. The Welsh Approved Document L asks for 0.16 W/m²K, with 0.35 as the worst figure accepted where 0.16 is not feasible.

In both countries we contact the council's building control service or a registered building control approver before a full re-cover is priced as settled.

Related questions

How do you find where an EPDM roof is actually leaking from?

A stain inside may sit well away from the split, because water can run along under the sheet before it drops through. So the search starts at the roof, with seams, upturns, corners and outlets checked in turn, and the findings are photographed rather than judged from the ceiling stain alone.

What can I photograph before you come out?

Take the stain on the ceiling, any pool of water left on the roof a day after rain, and the roof from a window or another safe place. Please do not climb up to take them. A note of the dates it dripped, and what the weather was doing, helps the survey.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing