01432 610152 Get a quote Call 01432 610152

Lightweight tiles

Lightweight tile systems for conservatory roofs

A lightweight tile system gives a conservatory a solid roof with a tiled look, without the full build of a traditional tiled roof. This guide covers what to check and which rules apply.

Horizon Roofing Hereford 9 min read

Replacing the glass or polycarbonate on a conservatory with a solid roof changes the room more than any other single job. It cuts glare, stops the greenhouse effect on a hot afternoon and gives the room a roof that matches the house. The worry is weight. Everything under the roof, from the glazing bars to the footings, was drawn for a light load, and a conventional tiled build adds timber rafters, insulation, battens and a heavy covering.

Lightweight tile systems are sold as the answer: a factory-made roof, delivered as panels or a kit, that gives a tiled finish on a lighter structure. They can suit the right frame, but they are not a loophole in the rules. Every one of them still has to be fixed, ventilated, insulated and signed off.

The sections below explain what these systems are, what to ask a supplier, how weight and pitch are checked, and what the Building Regulations ask in England and in Wales. For the other roofs we fit, see our conservatory roofs page.

What a lightweight tile system actually is

The name covers a range of products, so it helps to be clear about what is being compared. A traditional solid tiled roof is built on site from rafters, boards or insulation, battens and clay or concrete tiles. A lightweight system arrives as a made-up roof: insulated panels or a framed kit, with a tile-look surface that may be a thin stone-coated sheet, a composite or a pressed tile. The details differ from one maker to the next, and so do the pitches and fixings that each one needs.

That variety is why we do not give a weight, a pitch or an insulation figure for "a lightweight tile roof" in general. Each maker publishes its own data sheet, and the data sheet is what the structural check uses. When a system is proposed, the questions to put to the supplier are straightforward:

  • What does the made-up roof weigh per square metre, including the covering?
  • What is the minimum pitch, and does the conservatory frame reach it?
  • How is the covering fixed, and which standard is it tested to?
  • What U-value does the maker state for the complete roof?
  • How does the roof meet the house wall, and who supplies the flashing?

A supplier who cannot answer those in writing is a supplier to be cautious about, because each answer feeds the structural check, the building control submission or the flashing detail. We would rather have the answers before the survey than after the scaffold goes up.

Weight, and the 15 per cent line

Weight is the check that decides whether a system can go on the frame at all. The rule that gives it teeth sits in Approved Document A, the structural document. Its paragraph 4.4 calls it a significant change when the loading upon the roof goes up by more than 15%, and the Welsh edition of the document repeats that test. The Planning Portal puts it as a rise of 15 per cent or more, so the two sources differ at exactly 15, and we name whichever one we are relying on.

When a roof is made heavier past that line, the work needs Building Regulations approval and a structural check. For a conservatory the comparison is not tiles against tiles. It is the new made-up roof against the old glazed roof, and the figures for both come from the makers.

What the weight check compares
ItemWhere the figure comes from
Old glazed roofFrame maker or a survey of the glazing
New made-up roofThe system maker's data sheet
Walls and foundationsA structural check on site
Snow and wind on the roofThe designer's calculation

Our guide on whether the frame and walls can take a solid roof sets out how the structural check is carried out. The short point for this page is that a lighter system narrows the gap but does not remove the need for the check, and the dwarf walls and their foundations are the parts that tend to set the limit.

Pitch and fixings

Pitch is the slope of the roof, measured in degrees, and every covering has a minimum below which water can be driven back under it. Marley's published table shows how widely those minimums vary even within one maker's range, from 12.5° for a Mendip 12.5 concrete tile to 40° for a Canterbury clay tile, with Double Roman at 22.5° for the smooth version and Anglia at 25°. Marley adds that you should always check the product data sheet. A lightweight system will have its own figure, and a conservatory roof can be shallower than a house roof, so the system has to be chosen with the pitch in hand.

Fixing is the other half. BS 5534:2014+A2:2018 is the edition now current for slating and tiling, and Marley points out that fitting to BS 5534 is not a legal requirement, though since the 2015 amendments mortar on its own has not been accepted as enough to fix the covering. That matters at ridges and edges, where tiles meet the wind first. BS 8612 covers dry-fix, a mechanical alternative to bedding ridge and verge parts in mortar.

The mortar question matters on a conservatory because the roof edges are close to the ground and the wind, and a ridge that moves is easy to see from the garden. We treat the maker's fixing schedule as the minimum. Exposed positions, such as a roof that stands proud of the garden wall, are fixed to the data sheet and no less. If you have ever seen a ridge line shift after a storm, you will understand why: the weakest fixing sets the strength of the roof.

Which rules apply: England and Wales

In England, the Planning Portal tells owners that a replacement conservatory roof must meet the building regulations on structure, energy use and ventilation. A solid roof, lightweight or not, is a new roof, which is why we advise a call to building control before ordering and not after.

Part L targets for a roof added to a house that already stands
ElementEngland, AD L 2021 Table 4.2Wales, AD L Table 4.1
Roof0.150.13
Window or roof window1.4 or WER Band B1.4 or WER Band B
Rooflight2.22.2

The two countries are not interchangeable, so a property near the border should be checked against the right column, not the nearer council. These figures apply where Part L applies to the conservatory. England follows AD L 2021 until its 2026 edition begins on 24 March 2027. Wales has a new Approved Document L starting on 4 March 2027. Whether a conservatory is exempt turns on a list of conditions, set out in England in AD L paragraph 0.14, and a solid roof is one of the changes to put to building control before assuming the exemption survives.

Building control is carried out by the council or by a registered building control approver. The approach is the same in both countries: send the make-up of the roof and the structural check, then wait for the answer in writing. Our guide to approval for a solid roof looks at that step from the owner's side.

Insulation, ventilation and the wall junction

A lightweight system keeps warm through its insulation and dry through its ventilation. Makers state a U-value for the complete roof, and that is the figure compared with the table above. If the maker gives a value for the panel alone, ask for the whole roof, because the edges, the ridge and the junction with the house all let heat through.

Underlay is a small detail with a large effect, hidden once the covering goes on, so it is checked before that point. Marley's cold-roof advice separates the two types. High-resistance underlay holds back moisture vapour, so it needs a ventilated eaves, set at 25mm for pitches of 15° or less and at 10mm above that. A low-resistance, air-permeable underlay over a tightly sealed ceiling can lean on 3mm of ordinary eaves leakage, subject to the maker's certification. A factory-made kit should settle this for you, but the instructions should be read before the roof is built, not after, and any change to the pitch or the junction can alter the ventilation it asks for.

Where the roof runs into the house wall, the detail needs the closest look. Lead is the usual flashing. Royston Lead's table lists Code 4 and above for flashings, with Code 3 recommended for lead soakers only. MyJobQuote says a correctly fitted lead flashing "can last for over 80 years", which is a hedge and no promise for this junction.

We state what the junction will be, and how it is flashed, before the quote is agreed.

Cost and lifespan for a tiled conservatory roof

MyJobQuote's October 2026 page puts the average conservatory roof replacement this year at £3,200 to £6,000. That range spans every roof type, so a lightweight tile roof may fall inside it or outside it depending on the frame, the roof size and the system. The price of the system is only part of the answer. Strengthening the walls, bringing in a structural engineer, scaffold, roof windows and making good inside can each move the total. Ask for the system price and the extra work to be shown as part of the same written quote, so nothing arrives later as a surprise.

On lifespan, HomeBuilding sets out three bands, two of them quoted from Roofing Megastore's managing director: 10 years for polycarbonate, over 30 years for glass, and over 50 years for tiled roofs. Those figures are for tiled roofs as a type, not for any one lightweight product, and a maker's own claim for its system should be asked for in writing and read with care. A guide to how long a tiled conservatory roof lasts goes further.

Our quote is a single price in writing after the survey, so you can set it beside a glass or polycarbonate alternative on equal footing. Photos of your own roof and walls go with it, taken at the survey, and if a lightweight system is not the right answer for your frame, we say what is.

The choice may not be between good and bad systems. It is between a system that suits this frame, this pitch and this house wall, and one that does not.

Questions about lightweight tile roofs

Is a lightweight tile roof exempt from Building Regulations?

No system is exempt by name. According to the Planning Portal, a replacement roof must meet the building regulations, and any exemption depends on a list of conditions. Send the make-up of the roof to building control before you order, and wait for the reply.

Will my existing frame take a lightweight tile system?

It depends on the glazing bars, the dwarf walls and their footings, which need a structural check against the maker's weight figure, giving a clear yes, a yes with strengthening, or a no. Approved Document A calls it significant when the loading upon the roof rises by more than 15%, so the comparison with the old roof matters.

How long will a lightweight tile roof last?

A roofing retailer's managing director, quoted by HomeBuilding, puts tiled conservatory roofs above 50 years, but that is a figure for the roof type. Ask the maker of a particular system for its stated lifespan in writing, and read the conditions attached, since a claim that depends on maintenance or on a specific pitch can fall away if either is missed.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing