01432 610152 Get a quote Call 01432 610152

Roofline lifespan

How long do uPVC soffits and fascias last on a Herefordshire home?

Firms that sell uPVC boards quote a long life, and the boards can last. This guide covers what that range means, what wears a roofline out early, and why the soffit matters.

Horizon Roofing Hereford 9 min read

Search for how long fascias last and the first answers come from companies that sell them. One retailer, Plastic Centre, says that uPVC boards typically hold up for "between 20 and 40 years". That is a seller's figure, from a firm that gains when you buy boards, and it describes boards that were fitted well and then left alone. It is a fair starting range, but not a promise about your boards.

The roofline is the strip running under the lowest edge of the roof, and our guttering, soffits and fascias service covers all of it. The fascia is the board on the outer face that supports the gutter. The soffit is the underside board that closes off the space between the wall and the back of the fascia. On a gable end the matching board is the bargeboard, which follows the sloping edge of the roof instead.

The guide follows the order of a survey: what the range can and cannot tell you, what wears boards out, the air that moves through a soffit, old white boards that may not be uPVC at all, and doing the roofline in the same visit as a re-roof. The rules differ across the border for that last one, so each is labelled England or Wales.

A retailer's 20 to 40 years, read with care

The range is wide. Twenty years and forty years are a whole generation of weather apart, and nothing in the sentence says which end a given house will reach. A board on a sheltered gable and a board above a noisy, overflowing gutter will not wear at the same pace.

The source matters too. A retailer sells replacement boards, so a long life makes the product look good, and a short one sends customers back to buy again. Neither motive makes the figure wrong. It means the number should be read as a sales-side estimate and tested against the board itself, which you can see from the garden.

A lifespan range cannot tell you any of these things about your own roofline:

  • When the boards were fitted, and whether they replaced timber or were fitted over it
  • How well the joints, corners and fixings were made
  • Whether the gutter above has leaked onto them for years
  • Whether the soffit was vented when the boards went up
  • What the old timber behind the new face now looks like

So we judge by condition. On a survey we photograph the boards, the joints and the gutter run from the ground, and from a tower or ladder where the job needs it, and you see the pictures of your own house. A board in good order at thirty years does not need replacing because a webpage said thirty.

What shortens the life of a uPVC roofline

The board face is only the visible part of the job. Behind a fascia sit the rafter ends (the sloping timbers that reach out past the wall) and, on some houses, an older timber board that the plastic was fitted over. A uPVC face can look tidy for years while the timber behind it is wet.

These are the things that cut a roofline short, from what we see once the gutters are down:

  • A gutter that overflows or leaks at its joints, wetting the board and the timber behind it.
  • A sagging gutter whose weight pulls on the fascia and the fixings that hold it.
  • Joints and corners that were cut short or left open when the boards were fitted, which then gape as the plastic moves with the temperature.
  • Fixings driven into soft or rotten timber, so the board loosens and bows.
  • Knocks from ladders, which can crack a board or spring a joint.
  • Birds and insects getting in at an open soffit edge.

You can check most of this from the lawn. Look along the fascia for waves, gaps at the corners and any board that sits proud of its neighbour. Look under the gutter for green or black staining on the face, which tells you where water has been running over it.

When only one section is damaged and the rest is sound, mending that section is the better buy. Where the timber behind has gone, capping over the top only hides it. Our short guide to capping or replacing fascias sets out the difference.

The soffit is where the roof breathes

A pitched roof with a cold loft (an unheated loft with insulation laid on the ceiling below) needs air to pass through it. That air can enter at the eaves, and on some houses the soffit is where it gets in. Replace the boards without leaving the gap open and you can shut the roof's only intake.

Marley, a tile maker, sets out what it says is needed at the eaves. Its figures change with the type of underlay fitted under the roof tiles.

Eaves ventilation for a cold roof, as published by Marley
Roof set-upEaves opening Marley gives
HR underlay, pitch of 15 degrees or less25mm, continuous along the eaves
HR underlay, pitch of more than 15 degrees10mm, continuous along the eaves
LR underlay (air-permeable), ceiling well sealedAbout 3mm of ordinary eaves construction can serve, but only where every condition of the maker's third-party certification is satisfied

HR stands for high resistance. HR underlay is a sheet that vapour cannot pass through, so the roof relies on the eaves opening to dry out.

For your roofline, the sensible question for anyone quoting is what happens to the airflow. A vented soffit, or a vent fitted into the eaves, keeps the path open. The check also runs from the inside: insulation packed tight into the eaves of the loft can close the same gap from the other side, so we look at both the boards outside and the insulation inside before we say what the roof needs.

Older white boards that may not be uPVC at all

Not every pale board under an eaves is plastic. HSE's advice is plain: "If the building was built or refurbished before 2000, assume that there is asbestos in it." Its list of places asbestos turns up in a building includes "AIB white soffit panels to underside of roof eaves" and a "damaged AIB soffit". AIB stands for asbestos insulating board, a flat panel once fixed beneath eaves.

So before anyone drills, sands or saws a soffit on an older house, treat it as suspect. The rules on what can be done differ by material:

  • Asbestos cement in forms like roof sheeting and rainwater goods sits on HSE's non-licensed list so long as it comes off whole and is not broken up on the way.
  • Cement sheets that are already substantially damaged, or that would shatter on removal, become notifiable non-licensed work.
  • Taking out asbestos insulating board is mostly licensed work, which passes to a specialist asbestos firm rather than a roofer.

The waste has its own paperwork. In England, the consignment-note exemption for households covers domestic hazardous waste "other than asbestos waste"; in Wales, Natural Resources Wales says "contractors moving asbestos from a domestic property will need to use consignment notes". HSE guidance on skips asks for a lockable one when asbestos is carried.

We check what is under the eaves before a quote, because it changes who does the job. Our guide to asbestos soffits set out what happens next.

Doing the roofline with a re-roof

The fascia carries the gutter and sits where the lowest row of tiles ends. When a roof is stripped, the underlay at the eaves is dressed down into the gutter and the bottom courses are laid to overhang it, so that edge is opened up whatever happens to the boards. Scaffold is also going up for the roof, and the same scaffold reaches the roofline.

That is the practical case for one visit. Replace the roofline afterwards and the new boards have to be cut in against finished work, with the gutter taken down a second time. Our answer on whether fascias should be replaced with a new roof goes through it.

England and Wales treat a re-roof differently:

  • For an English address, the Planning Portal puts the no-application case at "Less than 25 per cent of the total 'building envelope'" together with "Less than 50 per cent of the roof is affected".
  • On weight, still for England, the Portal asks for approval where a covering "increases the weight of the roof covering by 15 per cent or more".
  • In Wales, the Welsh Government's page on re-roofing begins: "In most situations, this work will need Building Regulations approval."

On a Herefordshire address we use the English test, and on a Monmouthshire or Powys address we check with the council's building control service first. The same visit lets you ask what the old boards were made of, since that has to be settled before the stripping starts.

The written price takes in the scaffold, the roof and the roofline as a single total, and the old boards and gutters are cleared away when the work is finished.

What to look at from the garden first

A walk round the house with a phone camera tells you most of what a survey starts with. Do it in dry light and stand far enough back to see the whole run of each elevation. Keep both feet on the ground.

  1. Look along each fascia for waves, bowing or a board that has dropped away from its neighbour.
  2. Check every corner and every joint between boards for gaps.
  3. Look beneath each gutter for dark staining, then at the gutter itself for sagging between its brackets.
  4. Look up at the soffit from beneath for sagging, holes, staining or a vent that has been painted shut.
  5. Photograph anything that looks wrong, starting wide, then moving in on each fault.

If the house is older than 2000 and the soffit panels are flat, white and not obviously plastic, leave them alone and mention it when you ask for a survey. Do not scrape, wire-brush or pressure wash them.

Where the boards are in good order and the faults are confined to spots, a repair keeps the sound boards in place. If whole runs have bowed or the timber behind is wet, a replacement is the honest answer. After the survey you get a written total, backed by photographs taken along your own roofline, and those pictures are the basis for the decision.

Herefordshire houses vary a great deal in how they are built. A brick semi, a cottage with exposed timber framing near Pembridge and a stone house in the Golden Valley each meet the roof differently at the eaves. We match the fix to the construction in front of us, and no number from a webpage replaces that look.

Questions about boards and soffits

Does a new roofline need vented soffits?

It needs the roof to keep an airway at the eaves where the roof was built to rely on one. Marley gives openings of 25mm or 10mm for HR underlay, depending on pitch. We check the underlay and the existing intake before choosing boards, and fit vents where the airway would otherwise be lost.

Can fascias be changed without disturbing the gutters?

Not without touching them. The gutter is fixed to the fascia, so it comes down, the board is renewed, and the gutter goes back or is replaced if it is cracked or out of fall. That is why gutter and roofline work share a scaffold and a visit.

Should I touch the old white boards under my eaves before a survey?

Not until they have been identified. HSE tells owners of a building built or refurbished before 2000 to assume that asbestos is present. Photograph the boards from the ground and mention them when you book, so the survey can plan who does the work. Please leave them undisturbed until then.

Get your free roof quote

Tell us about the roof and we will arrange a survey.

10-year workmanship guarantee, in writing